Answered: A total current I flows through the…

A total current I flows through the networks of resistors shown in the figure. In which of the arrays is the dissipated power the largest? R (A) R (B) ww R R ww- R www R (C) (D) R R R R R R ww

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter20: Electric Current, Resistance, And Ohm's Law

Section: Chapter Questions

Problem 77PE: In this problem, you will verify statements made at the end of the power losses for Example 20.10....

See similar textbooks

Similar questions

Why do incandescent lightbulbs grow dim late in their lives, particularly just before their filaments break?
Analog meters use a galvanometer, which essentially consists of a coil of wire with a small resistance and a pointer with a scale attached. When current runs through the coil, the point turns; the amount the pointer turns is proportional to the amount of current running through the coil. Galvanometers can be used to make a voltmeter if a resistor is placed in series with the galvanometer. Consider a galvanometer that has a resistance of 25.00 and gives a full scale reading when a 50A current runs through it. The galvanometer is to be used to make an voltmeter that has a full scale reading of 10.00 V, as shown below. Recall that a voltmeter is connected in parallel with the component of interest, so the meter must have a high resistance or it will change the current running through the component, (a) What is the potential drop across the series resistor in the meter? (b) What is the resistance of the parallel resistor? Av = lo.oo v
Foolishly trying to fish a burning piece of bread from a toaster with a metal butter knife, a man conies into contact with 120-V AC. He does not even feel it since, luckily, he is wearing rubber-soled shoes. What is the minimum resistance of the path the current follows through the person?
Why isn’t a short circuit a shock hazard?
Why isn’t a short circuit necessarily a shock hazard?
In view of the small currents that cause shock hazards and the larger currents that circuit breakers and fuses interrupt, how do they play a role in preventing shock hazards?
Analog meters use a galvanometer, which essentially consists of a coil of wire with a small resistance and a pointer with a scale attached. When current runs through the coil, the pointer turns; die amount the pointer turns is proportional to the amount of current running through the coil. Galvanometers can be used to make an ammeter if a resistor is placed in parallel with the galvanometer. Consider a galvanometer that has a resistance of 25.00and gives a full scale reading when a 50A current runs through it. The galvanometer is to be used to make an ammeter that has a full scale reading of 10.00 A, as shown below. Recall that an ammeter is connected in series with the circuit of interest, so all 10 A must tun through the meter, (a) What is the current through the parallel resistor in the meter? (b) What is the voltage across the parallel resistor? (c) What is the resistance of the parallel resistor?
Find the current through a person and identify the likely effect on her if she touches a 120-V AC source: (a) if she is standing on a rubber mat and offers a total resistance of 300 k; (b) if she is standing barefoot on wet grass and has a resistance of only 4000 k .
In this problem, you will verify statements made at the end of the power losses for Example 20.10. (a) What current is needed to transmit 100 MW of power at a voltage of 25.0 kV? (b) Find the power loss in a 1.00 transmission line. (c) What percent loss does this represent?
An office worker uses an immersion heater to warm 250 g of water in a light, covered, insulated cup from 20.C to 100. C in 4.00 minutes. The heater is a Nichrome resistance wire connected to a 120-V power supply. Assume the wire is at 100. C throughout the 4.00-min time interval. (a) Calculate the average power required to warm the water to 100. C in 4.00 min. (b) Calculate the required resistance in the heating element at 100. C. (c) Calculate the resistance of the heating element at 20. C. (d) Derive a relationship between the diameter of the wire, the resistivity at 20. C, 0, the resistance at 20. C, R0, and the length L. (e) If L = 3.00 m, what is the diameter of the wire?
Apply the loop rule to loops abgefa and cbgedc in Figure 21.47.
An office worker uses an immersion heater to warm 250 g of water in a light, covered, insulated cup from 20.C to 100. C in 4.00 minutes. The heater is a Nichrome resistance wire connected to a 120-V power supply. Assume the wire is at 100. C throughout the 4.00-min time interval. (a) Calculate the average power required to warm the water to 100. C in 4.00 min. (b) Calculate the required resistance in the heating element at 100. C. (c) Calculate the resistance of the heating element at 20. C. (d) Derive a relationship between the diameter of the wire, the resistivity at 20. C, 0, the resistance at 20. C, R0, and the length L. (e) If L = 3.00 m, what is the diameter of the wire?