A tourist driving in the Hijaz mountainous area of Saudi Arabia using an old Chevy car. His car's top speed is 100 kph with an accelgration of 4 ft/sec, a wt. of 3000 Ib. and a cross-sectional area of 4t x7ft. The roadway curves' radii range from 800-2000 ft with a posted max speed of 80 kph. The straight road sections have a posted max speed of 20 kThe road grades range from 10to +10%. What is the min engine power required to travel on the curves at max possible speed?

A tourist driving in the Hijaz mountainous area of Saudi Arabia using an old Chevy car. His car's top speed is 100 kph with an accelgration of 4 ft/sec, a wt. of 3000 Ib. and a cross-sectional area of 4t x7ft. The roadway curves' radii range from 800-2000 ft with a posted max speed of 80 kph. The straight road sections have a posted max speed of 20 kThe road grades range from 10to +10%. What is the min engine power required to travel on the curves at max possible speed?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An airplane starts from rest at t=0. During a curvilinear flight path, airplane’s acceleration in cartesian components is defined by ax= 0.46t + 0.2 m/s2 and ay= 0.6t m/s2. At t = 4 sec, Given the mass of aircraft is 1500 kg, calculate a) Normal and tangential forces
Q) A driver is driving a car in a circular ring which is 120 m in diameter. At one instant, his total acceleration is 12 m/s2 with a direction of 30° relative to the tangent. a) Determine his radial and tangential acceleration. b) Starting from the state described above and maintaining the same tangential acceleration, how long does he need to perform one complete circuit?
Applying principles of dynamics, with step by step solutions pls (i give 5 stars) A freighter is moving at a speed of 8 nautical miles per hour. The engines then had to be suddenly stopped. If it takes 10 minutes for the freighter to reduce its speed to 3 knots, determine the distance moved by the ship and its speed at the end of this interval. The deceleration of the ship is propor-tional to the square of its speed such that a = -kV^2.
QUESTION 7 PLS 6) A ball is thrown vertically upward from the surface of the earth with an initial velocity of 30 m/s. Two seconds later a second ball is thrown upward from the same point with a velocity of 24 m/s. Derive an expression for the relative position, velocity, and acceleration of ball 1 with-respect-to ball 2 for time t≥2sec. (neglect air resistance and assume acceleration of gravity is 9.81 m/s2. 7) For the two balls thrown in problem 6, how far above the earth will the two balls meet (i.e. what is their height when they pass each other)?
The shaft of a turbine rotor, initially at rest, accelerates uniformly for 0.9s at 25 rad/s2. Compute and identify the nearest value of the angle turned through by the shaft in degrees during this time. a. 960o b. 580o c. 645o d. 720o Clear my choice
an airplane turbofan compressor blade is 3.0 m long and is rotating at 12350 rmp. Calculate the following- angular speed, w_____________rad/s linear spped at the tip of the blade, v=_________m/s angular and linear displacement after 3.3s, 0= ___________rad s______________m
Find out the a.) Acceleration, b.) Speed at the 3.0s mark, and c.) Displacement at the 3.0s mark. Given the following initial conditions initial velocity=0 mass=5kg, static friction coefficient=0.4 kinetic friction coefficient=0.2, and angle of inclination =30degree
13.73. A model of a motorboat is driven at 4.57 m/s by means of a jet of water 25 mm in diameter, ejected directly astern. The velocity of the jet relative to the model is 35.1 m/s. What is the driving force? Ans. 543 N
A tire 0.400 m in radius rotates at a constant rate of 170 rev/min. Find the speed of a small stone lodged in the tread of the tire (on its outer edge). (Hint: In one revolution, the stone travels a distance equal to the circumference of its path, 2?r.)____m/sWhat is the acceleration of the stone?_____m/s2 away from the center of the path? tangent to the path? toward the center of the path?
AB=5 cm, BO4=CO4=2.5 cm, DC=5 cm, O7E=ED=5 cm, FE=2.5cm, O8F=2 cm’ dir. AB: horizontal, BO4: Vertical, CO4: horizontal, DC: Vertical, O8F: horizontal, and FE ꓕ DO7. V2=100cm/sec QUESTİON:Do the acceleration analysis.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Block B starts from rest and then moves to the right with a variable acceleration given by the acceleration-time curve. Determine:(a) the acceleration(b) the velocity of block A at t = 3.71 s.*dont copy other experts' answer, i'm looking for a different approach in solution can you please verify which among these two solutions is coreect?Solution 1: Step 1 Let T is the tension in each rope so 3T is acting on block B and 2T is acting on block A. So , 3T×aB=2T×aA×aB=2T×aA Hence,aA =32aBHence,aA =32aB Step 2 acceleration of block B = 0.29 ft/s2 (from graph) a)acceleration of block A (t=3.71s)= 32×0.29 ft/s2 =0.435 ft/s232×0.29 ft/s2 =0.435 ft/s2 b) Velocity of block B at (t = 3.71 s) = Area under the graph = 2ft/s2×1s−1ft/s2×1s+12×(2ft/s2+0.29ft/s2)×1.71s =2.96ft2ft/s2×1s-1ft/s2×1s+12×(2ft/s2+0.29ft/s2)×1.71s =2.96ft/s Velocity of block A at (t=3.71s) = 32×vB=32×2.96ft/s=4.44 ft/s Solution 2: *check the last…
A stroke of a reciprocating engine is 600 mm. neglecting the effect of angularity of the connecting rod, find a) velocity in m/s of the piston , b) acceleration of the piston in m/s^2 when the crank is 30 degree past TDC. The engine is running at 720 rev/min tools : r=1/2 stroke, v=wrsin theta! a=wr^2costheta