Answered: A transmission line conductor has a…

A transmission line conductor has a weight of 1.2 kg/m and the span of the line is 200 m. The maximum tensile strength of the carrier is 8000 kg. Calculate the sag assuming a factor of safety of four

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.3P: A transmission-line cable with a length of 2 km consists of 19 strands of identical copper...

See similar textbooks

Related questions

Q: Example: By Using the superposition theorem find I in the circuit shown in figure? 20V 50 30 100 +5A

A: The given circuit diagram is shown below: V-20/5+V/3=5 3V-60+5V=75 8V=135

Q: Find the current Ix if the voltage across the diode is 0.5V. The reverse saturation current of diode…

Q: State Gauge Factor. Derive the expression for Gauge factor

A: Given: State Gauge Factor. Derive the expression for Gauge factor.

Q: Consider the following Op Amp circuit. Choose the correct transfer function of the system, from…

Q: 2. Write the expression for the output Z (in terms of inputs A and B) for the following logic…

A: Given Boolean circuit,

Q: x(t) = 8(t - to)

A: In this case, the Laplace transform of the given function needs to be determined: xt=δt-t0

Q: In a 66 KV system the phase is ground capacitance is 0.05 µF and inductance is 2H. The voltage (kV)…

A: Given: A transmission line system circuit breaker configuration with, Interrupted current, i = 15 A…

Q: Find the current I if both diodes are identical. Voltage V = 0.8V and let the reverse saturation…

Q: What is the value of gm1 needed to keep the noise figure of the mixer below 10 dB? Assume R₁=R₂=500…

A: Gm stands for trans-conductance. The term gain is frequently used to refer to the current to voltage…

Q: 1. A field is given as Ğ = [x25,²] (xāx + yāy) . Find (a) a unit vector in the direction of G at +…

A: As per bartleby guidelines we need to answer 1 question for multiquestions.

Q: 2 10/0 θε 北 0325 行几嗨 9.2120 A b

Q: Problem #3: and I₂ In the circuit shown below find the current l₁ and voltage Vo 207 Is 5mA ↑ 2k AM…

A: Given circuit,

Q: A 220 V, 7 A, 1100 rpm DC shunt motor has armature and field resistance of 1.75 2 and 250 n…

Q: 1. Resistive circuits (20 points) A1 th Ik w W 12 In the circuit above, V1-15 volts. a) (10 points)…

A: Solution !!

Q: When a single phase energy meter is calibrated by a substandard watt meter the following results are…

A: Discrivolution : 10 Time taken : 12 seconds Wattmeter Reading : 2000 Watt Meter Frequency K : 1500…

Q: When an antenna is transmitting an unmodulated carrier, then the current is 10 amps and when the…

A: It is given that: It=total or modulated current=15 AIc=carrier or unmodulated current=10 A

Q: For the diode network of Fig. 2.30, sketch v₁, va and id if the input is sinusoidal of 50 Hz. Ideal…

A: We have an diode network as shown in figure. diode is ideal. We have been asked to sketch, vi vd id…

Q: For a FM signal v(t) = 20 cos ( 10 * 108t + 30 sin 3000t), calculate the power dissipated by the FM…

Q: 1. Resistive circuits (20 points) R3 RY www www 5 Voo www w

A: Solution !!

Q: Calculate the 25 Ω inductor current using Norton's theorem. 80/60° j30 Ω 20Ω του 70Ω -j70 Ω (…

Q: Problem2: Given the following DC circuit: U₁1 = 10 V R₁ = 59 12 R₂=2502 B Calculate current 13 using…

Q: Capacitance per unit area at no reverse bias is two pF/cm². For a step graded diode of area 5cm²,…

Q: A structural member is compressed to produce a strain of 5 µm/m. The nickel wire strain gauge has a…

A: Given, A structural member is compressed to produce a strain, ∆ll=5 μmm Gauge factor, GF=-12.1 The…

Q: R1 Click here for image 11 Rm/ In this circuit, R1 =502, 11-6 A, 12= 2 A, Rm = 82. / has units of…

A: We need to find out the thevenin equivalent circuit for given circuit

Q: Problem: Write down the mesh current equations for the circuit shown in the figure below and…

A: Solution:By applying KVL to the two meshes, we get5 I1 + 2(I1- I2)=1010 I2 + 2( I2- I1)=-50.

Q: For the control system shown below the input signal is X(t) and the output signal is y(t), the…

A: Given data,

Q: Example: By Using the superposition theorem find I in the circuit shown in figure?

A: It is given that:

Q: What Boolean Algebra equation represents the following function: F(A,B,C,D)= IIM (3,4,5,11,12,13) a)…

A: Given Boolean function, FA,B,C,D=∏M3,4,5,11,12,13

Q: What is the required received power in an FM system with = 5 if W = 15 kHz and No = 10-14W/Hz? The…

Q: Using the law below find the Value of Zs Ks- 25-20 25+ Zo Data: - Zo=100, KXs=0-5 150

A: We need to find out value of Zs for given formula

Q: 1) Compute the Fourier Transform of each of the following signal: a) [e-at cos wot]u(t), a > 0 b)…

A: Given: a e-atcosω0tut,α>0be-3tsin2tcxt=1+cosπt,t≤10, t>1

Q: -find Zr using Comblix number Zr = Zo ( 1+kr) - Kr kr-0.2828 +jo.2828 Zo= 50

Q: Question 2 A circuit has a voltage of 5020 V and a current of 52-10 A. The angle of the circuit's…

A: Given: Circuit voltage, V=50∠0° V Circuit current, I=5∠-10° A

Q: The conductors of a three phase transmission line are symmetrically arranged in a triangle. If the…

Q: 1.2 For the networks shown in the circuit below, find the values of the currents marked 10A 12 7A 41…

A: KIRCHHOFF'S CURRENT LAW [ KCL ] :- Acording to KCL " the algebraic sum of all the current entering…

Q: Find the Laplace transform of x(t)=-e-atu(−t)

Q: 2. For the circuit shown below 15 mA (a) Find v (b) Find the power of the resistor (c) Find the…

Q: For the circuit shown in Fig. 2 Find the current in the Thevenin and Norton equivalent circuits…

A: Given: Circuit diagram:

Q: 5. A separately-excited DC generator produces an open-circuit voltage of 240V with field current of…

Q: Give brief properties of High resistivity conducting material. (1) Carbon (2) Tungsten (3)…

A: As name it self indicates, the conducting material which have high resistivity are known as high…

Q: Calculate Z₁, that ensures maximum power transfer to 5 2 resistor.

A: It is given that: Zload=5 ohm

Q: The coil resistance of a microameter in the range of 50 microamperes is 2000 ohm. It is to be used…

A: the coil resistance of microameter in the range of given i=50μA, resistance r=2000 Ω =2 kΩ voltmeter…

Q: 20 nC/m at (0,y,18) -10 nC/m at (2.y,18) -10 nC/m at (2.y.18) A person 1.5 m tall Stands on the…

A: We have to find the value of electric field intensity E at head of the human. Then line Integrate…

Q: A 33 KV substation is to be connected to a 11 KV stepdown substation which is at a distance of 1.5…

A: We have Transmission line which connects 33 KV Sub-Station to 11 KV Substation. This line is 1.5 KM…

Q: 2. A 0.5uF capacitor has voltage waveform v(t) as shown in following figure, plot i(t) as function…

Q: Example: Determine the current in the 5 2 resistor shown in the circuit below 20 V V₁ 10 A 20 30 10.…

Q: Calculate the current I. 150 -jsn 4/60 20/45 V 80 30/75 j100 30/30* 70/60° V

Q: Q2. a) Explain why the static electric field is always zero inside an isolated conductor. What is…

A: Given Distance D=1.5 mm Electric potential 4.5 V. Electrical charge taken from b part +17 pC Find:…

Q: A circular disk of radius a [m] is uniformly charged with ps [c/m²]. If the disk lies on the z = 0…

A: Given,Radius of the disk =rmUniform charge = ρs c/m2The disk lies on z=0 plane.

Q: Find the Envolution of x(+) by itself (i.e., find y(t). y (+) = x (+) * x (+)), and sketch it x (+)…

A: In this question, We need to determine the output of the given given signal. We know Convolution…

Concept explainers

Fiber Optics

Fiber optics is a technology used to transmit the facts such as light or pulses with fiber or plastic over long distances. Visual fibers are about the width of a human hair strand and, when tied directly to a fiber-optic cable, can transmit multiple long-distance records and faster in different ways.

Question

A transmission line conductor has a weight of 1.2 kg/m and the span of the line is 200 m. The maximum tensile strength of the carrier is 8000 kg. Calculate the sag assuming a factor of safety of four.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the per-phase line loss in a 70-km-long transmission line is not to exceed 65 kW while it is delivering 100 A per phase, compute the required conductor diameter if the resistivity of the conductor material is 1.72108-m.
Calculate the capacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the three-phase line in Problem 4.18. Also calculate the line-charging current in kA/phase if the line is 110 km in length and is operated at 230 kV. Neglect the effect of the earth plane.
Approximately how many physical transmission interconnections are there between the United States and Canada? Across which states and provinces are the interconnections located?
The span of the same level transmission line is 300 m. The diameter of the conductor is 15 mm. Wind pressure intensity over the projected area is 45 kg/m²? If the density of the conductor material is 8900 kg/dm, find the sag. Also calculate the vertical sag. The ultimate tensile stress of the conductor is 5000 kg/cm²? Assume a factor
An Overhead transmission line has a span of 115 m. Ultimate strength is 3600 Kg and factor of safety is 2. If the sag is 3 m, If the weight due to wind is 1.5 kg/m, Determine(a) weight of the conductor and(b) Length of the line
A transmission line is supported from two towers at heights of 40 m and 58 m above ground level, the horizontal distance between the towers being 300 m. If the maximum allowable tension is 2500 kg, find the minimum clearance and the clearance at a point mid-way between the towers. Weight of conductor is 1 kg/m.
3. A transmission line has a span of 150 m between level supports. The cross-sectional area of the conductor is 1·25 cm2 and weighs 100 kg per 100 m. The breaking stress is 4220 kg/cm2. Calculate the factor of safety if the sag of the line is 3·5 m. Assume a maximum wind pressure of 100 kg per sq. metre. [4]
A transmission line has a span of 250 meters between the line supports. The conductors has a cross sectional area of 1.29 cm2 and weighs 1170 kg/km and has a breaking stress of 4218 kg/cm2. Calculate the sag and vertical sag with a safety factor of 5, with a wind pressure of 122 kg per square meter of the projected area.
Prove that transmission efficiency increases with increasing transmission voltage or By increasing the cross-sectional area of the conveyor wire When the power generated is proven and line length The specific and resistance of the wire and the power factor
The span of a transmission line is 150 meters. The area of the conductor is 0.7 sq. cm. is There is an ice layer of 1 cm radial thickness on the conductor. The ultimate tensile stress of the carrier material is 5000 kg/cm^2. The specific gravity of carrier and ice is 8.9 and 0.915 respectively. Calculate the sage assuming a factor of safety of 4.
The transmission line has the following dataweight of the conductor = 8.2 kg/m, working tension = 1765 kg, and the conductor sag = 4.2 meter, then the distance between the towers is ....................
1. A transmission line conductor is supported from two towers at heights of 70 m above water level. The horizontal distance between the towers is 300 m. If the tension in the conductors is 1500 kg, find the clearance at a point mid-way between the towers. The size of the conductor is 0·9 cm2 and density of conductor material is 8·9 gm/cm3.