Q3A transmission shaft consists of twoparts: 2 m long and 50 mm diameteraluminum shaft is to be connected to ahollow steel shaft of the same lengthand ( 92 ) mm outside diameter.Determine the inside diameter of thehollow shaft if the stiffness of Shaft T/e=7800 Nm/rad.. Take the modulus ofrigidity of the steel twice of that ofaluminum. Gsteel=80 GN/m2.Your answer

Given data for the steel shaft.

Answered: A transmission shaft consists of two…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2. A mild steel shaft transmits ‘P’ kW at ‘N’ r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa. Power P in KW= 25 , Speed N in rpm=150
The stepped shaft shown in the figure isrequired to transmit 600 kW of power at 400 rpm.The shaft has a full quarter-circular fillet, and thesmaller diameter D1 =100 mm.If the allowable shear stress at the stress concentrationis 100 MPa, at what diameter D2 will thisstress be reached? Is this diameter an upper or alower limit on the value of D2?
The internal loadings at a critical section along the steel drive shaft of a ship are calculated to be a torque of 2300 lb # ft, a bending moment of 1500 lb # ft, and an axial thrust of 2500 lb. If the yield points for tension and shear are sY = 100 ksi and tY = 50 ksi, respectively, determine the required diameter ofthe shaft using the maximum shear stress theory.
Find the diameter of the propeller shaft, which has to transmit power of 1.5 kW at 8 Hz without exceeding shear stress of 25 MPa.
A hollow circular shaft 20mm thick transmits 294 kW at 200rpm.Determine the diameters of the shaft if the shear strain due to torsion is not to exceed 8.6 x 10 -4. Take Modulus of Rigidity as 80GN/m2
Determine the limiting peripheral velocity of a steel ring if the allowable stress is 20 ksi the steel weighs 490lbm /ft^3 . What is the resulting stress if the ring rotates at 6500rpm ? Use r = 10in
A solid shaft is required to transmit 90 kW of power at 200 rpm. Determine the shaft diameter by the strength design and rigidity design and from this design choose the suitable diameter of the shaft, if the permissible stress for the material is 50 N/mm2 and the permissible twist is 10 per meter length. Also, determine the maximum shear strain acting on the shaft.Take modulus of rigidity = 150 GN/m2.
The propeller shaft of a large ship has anoutside diameter 18 in. and inside diameter 12 in., asshown in the figure. The shaft is rated for a maximumshear stress of 4500 psi.(a) If the shaft is turning at 100 rpm, what is themaximum horsepower that can be transmittedwithout exceeding the allowable stress?(b) If the rotational speed of the shaft is doubledbut the power requirements remain unchanged,what happens to the shear stress in the shaft?
Hoop stress is limited to (2.4)MPa and density of flywheel material is (7504) Kg/m3
A closely coiled helical spring is to carry a load of 500N. Its mean coil diameter is to be 10 times that of the wire diameter. Calculate these diameters if the maximum shear stress in the material of the string is to be 8OMN/mA2.
A steel pipe of length L= 3 ft, outside diameter d₂- 10 in., and inside diameter dy = 5.1 in. is compressed by an axial force P= 107 kips. The material has = Poisson's ratio v=0.30. Determine the increase in thickness.
A hollow steel shaft of length 1.75 m transmits 2000 kW of power at a speed of150 rev/min. The inside diameter is to be 0.75 times the outside diameter. Themaximum allowable torsional shear stress for the steel is 130 MN/m2and themodulus of rigidity (G) for the steel is 83 GN/m2. Given that a factor of safety of2 is required for the shaft, determine:i) the torque acting on the shaft;ii) the required external and internal diameters for the shaft; iii) the torsional shear stress set-up in the shaft material at the inside surfaceof the hollow shaft, and sketch the stress distribution through the shaftwall;iv) the angle of twist (in degrees) due to the torque.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A transmission shaft consists of two parts: 2 m long and 50 mm diameter aluminum shaft is to be connected to a hollow steel shaft of the same length and ( 92 ) mm outside diameter . Determine the inside diameter of the