A tree contractor has been hired by a homeowner toremove a damaged tree from a previous storm. The top ofthe tree broke off, leaving the trunk in the ground. Thearborist will remove the tree by attaching a rope near thetop and cutting the base close to the ground. The scenariois shown in the figure.The distances in the figure are z = 12.0 m, hy = 4.83 m and x = 11.96 m. If the arborist pulls on therope with a force of magnitude F = 35.1 N, write theexpression for the torque 7 with respect to the base P of thetree using ijk unit vector notation,7 = txi + Tyj + T₂kwhere Tx, Ty, and Tz are the values of the torquecomponents in the x-, y-, and z-directions, respectively.= 1.45 m,kPXTh

Given:- A figure shows that the top of the tree broke off, leaving the trunk on the ground. The…

A tree contractor has been hired by a homeowner to remove a damaged tree from a previous storm. The top of the tree broke off, leaving the trunk in the ground. The arborist will remove the tree by attaching a rope near the top and cutting the base close to the ground. The scenario is shown in the figure. The distances in the figure are z = 12.0 m, h = 1.45 m, y = 4.83 mand x = 11.96 m. If the arborist pulls on the rope with a force of magnitude F = 35.1 N, write the expression for the torque 7 with respect to the base P of the tree using ijk unit vector notation, 7 = Txi + Tyj + T₂k where Tx, Ty, and Tz are the values of the torque components in the x-, y-, and z-directions, respectively. k 1 P T h 2 i

A tree contractor has been hired by a homeowner to remove a damaged tree from a previous storm. The top of the tree broke off, leaving the trunk in the ground. The arborist will remove the tree by attaching a rope near the top and cutting the base close to the ground. The scenario is shown in the figure. The distances in the figure are z = 12.0 m, h = 1.45 m, y = 4.83 mand x = 11.96 m. If the arborist pulls on the rope with a force of magnitude F = 35.1 N, write the expression for the torque 7 with respect to the base P of the tree using ijk unit vector notation, 7 = Txi + Tyj + T₂k where Tx, Ty, and Tz are the values of the torque components in the x-, y-, and z-directions, respectively. k 1 P T h 2 i

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 28P: A uniform beam resting on two pivots has a length L = 6.00 m and mass M = 90.0 kg. The pivot under...

See similar textbooks

Similar questions

A uniform plank of length 2.00 m and mass 30.0 kg issupported by three ropes, as indicated by the blue vectors inFigure P8.27. Find the tension in each rope when a 700.-Nperson is d = 0.500 m from the left end.
A uniform plank of length 2.00m and mass 30.0kg is supported by three ropes, as indicated by the blue vectors in figure p8.27. Find the tension in each rope when a 700-N person is d=0.500m from the left end.
A person is standing on a section of uniform scaffolding as shown in the figure. The section of scaffolding is L = 1.50 m in length, has a ms = 25.5 kg mass, and is supported by three ropes as shown. Determine the magnitude of the tension in each rope when a person with a weight of Wp = 660 N is a distance d = 0.700 m from the left end.
A thin rod of mass m and length L is released from rest from a nearly upright position, let’s say θ = 89o. What is the minimum height from which the rod should be released in order to land horizontally when it hits the ground.
A 10.0-kg monkey climbs a uniform ladder with weight w = 1.09 ✕ 102 N and length L = 3.40 m as shown in the figure below. The ladder rests against the wall at an angle of ? = 60°. The upper and lower ends of the ladder rest on frictionless surfaces, with the lower end fastened to the wall by a horizontal rope that is frayed and that, can support a maximum tension of only 80.0 N.
From the step ladder shown in the figure, sides AC and CE are each 2.44 m long and hinged at point C. Bar BD is a tie-rod 0.762 m long, halfway up. A man weighing 845 N climbs 1.8 m along the ladder. Assuming the floor is frictionless and neglecting the mass of the ladder, find the tension (in N) in the tie-rod.
a 15kg child is sitting on a playground teeter-totter, 1.5 m from the pivot. what is the minimim distance, on the orher side of the pivot, such that a 220N force will make the child lift off the ground?
A 2.4 m ladder rests on a vertical wall as shown in the figure. The ladder has 7 rungs and the rungs are spaced 0.30 m apart, and the top and bottom rungs are 0.30 m from their respective ends of the ladder. Surfaces at A and B both have the same coefficient of friction. If a worker weighs 360 N and stands on the middle rung, determine the minimum value of the coefficient of friction so that the ladder does not slide. Neglect the weight of the ladder.
A uniform beam of length 7.60 m and weight 4.50 × 102 N is carried by two workers, Sam and Joe, as shown. Determine the force that each person exerts on the beam.
As shown in the figure below, a uniform beam is supported by a cable at one end and the force of friction at the other end. The cable makes an angle of ? = 30°,the length of the beam is L = 2.75 m,the coefficient of static friction between the wall and the beam is ?s = 0.460, and the weight of the beam is represented by w. Determine the minimum distance x from point A at which an additional weight 2w (twice the weight of the rod) can be hung without causing the rod to slip at point A.x = _________m
A uniform beam of length L = 2.2 m and mass M = 33 kg has its lower end fixed to pivot at a point P on the floor, making an angle θ = 15° as shown in the digram. A horizontal cable is attached at its upper end B to a point A on a wall. A box of the same mass M as the beam is suspended from a rope that is attached to the beam one-fourth L from its upper end.What is the y-component Py of the force, in newtons, exerted by the pivot on the beam? Py = Write an expression for the tension T in the horizontal cable AB. T = What is the x-component Px of the force, in newtons, exerted by the pivot on the beam? Px =
As shown in the figure below, a uniform beam is supported by a cable at one end and the force of friction at the other end. The cable makes an angle of ? = 30°, the length of the beam is L = 2.00 m, the coefficient of static friction between the wall and the beam is ?s = 0.460, and the weight of the beam is represented by w. Determine the minimum distance x from point A at which an additional weight 2w (twice the weight of the rod) can be hung without causing the rod to slip at point A.x =______ m