A TRUCK is SHolelinG LiquiD slusH (8 = 20 kg/m³) THE SUSH is THROWN FORWARD AT e= 60° As SHOWN . THE BADE is 3m wiDE. → Va 5/s Ih= 0.5m a) calalaTE THE Hass Fow RATE OF slusH REMOVED FROM THE ROAD b) MAKE A SCHEMATIC OF A CONTRd voluMe AROUND THE BlADE INDICATE FORCES AND MASS FOw RATES IN 2 QUT OF THE CV. c calculATE THE VERTICA FORCE THAT THE slusH EXERTS ON THE elADE (NEGATIVE OP (MAGNITUDE 8 DIRECTİON) THe REACriON FORCE d) dalolATE THE HopiZONTAl FORCE AT THE shsH ERERTS ON THE BLADE (HAGN ITUDE E DIRECTnioN) berRA "e) How is THE TRUCK ABle To PROJIDE SUCH HORIZONTA FORCE? *F) waulb A LARGER O (Sax e=90°) RESulT iN A LARGER OR SMAller HorizONnA) FORCE

A TRUCK is SHolelinG LiquiD slusH (8 = 20 kg/m³) THE SUSH is THROWN FORWARD AT e= 60° As SHOWN . THE BADE is 3m wiDE. → Va 5/s Ih= 0.5m a) calalaTE THE Hass Fow RATE OF slusH REMOVED FROM THE ROAD b) MAKE A SCHEMATIC OF A CONTRd voluMe AROUND THE BlADE INDICATE FORCES AND MASS FOw RATES IN 2 QUT OF THE CV. c calculATE THE VERTICA FORCE THAT THE slusH EXERTS ON THE elADE (NEGATIVE OP (MAGNITUDE 8 DIRECTİON) THe REACriON FORCE d) dalolATE THE HopiZONTAl FORCE AT THE shsH ERERTS ON THE BLADE (HAGN ITUDE E DIRECTnioN) berRA "e) How is THE TRUCK ABle To PROJIDE SUCH HORIZONTA FORCE? *F) waulb A LARGER O (Sax e=90°) RESulT iN A LARGER OR SMAller HorizONnA) FORCE

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.50P

See similar textbooks

Similar questions

A windmill turns a series of slender rods fixed about one end . They are initially 2 meters long, and go at a speed of 15 revolutions per minute. I suggested making the blades 1m long to reduce the cross-sectional area of the windmill, keeping the mass the same for mechanical stress consistency. How fast are the windmill blades going now, in revolutions per minute?
What is the maximum power generated by the wind farm with wind speed of 4 m/s? Typical wind turbines have rotor diameters from 40 m to 90 m (Assume increment of 5 m for this problem)-40 m is 80% efficient and efficiency decreases by 5% for every 5 m increase in diameter (i.e. 45 m=75%, 50=70...)-The ridge is 10 km long and wind turbines will be spaced in a single row. •Power in the wind per unit area of circular area is 1/2ρv3W/m2 (v is the wind speed, ρ is 1.3 kg/m3 for air) •Wind turbines cannot be spaced closer than 5 times its diameter without loosing power also there are no partial turbines.
Diagram of the problem, necessary formulas, clearance and numerical solution A sphere of radius 50 cm is immersed in mineral oil (ρ = 1,200 kg/m3), what is the thrust it receives?
Fast pls solve this question correctly in 5 min pls I will give u like for sure Class: Structures 1 Question: locate the centroid of the box section shown, a cross-section often used in bridge construction Answers: Ax=0 Ay=3.92 kn By=11.08 kn Sub.
Design a 1 MW wind Turbines: given data tower height : 80 mblade length: 38 maverage wind speed: 6.9 m/s power: 1 MW
In Fig. let y1 = 95 cm and y2 = 50 cm. Estimate thefl ow rate per unit width if the upstream kinetic energy is(a) neglected and (b) included.
Show how you can use an energy method to compute the exact value of theradial displacement at x = L. You do not have to (but are welcome to) evaluate the final expression, if it is too complex to do by hand.
Consider a 20°C fl ow at 2 m/s through a smooth 3-mmdiameter microtube which consists of a straight run of10 cm, a long radius bend, and another straight run of10 cm. Compute the total pressure drop if the fl uid is(a) water; and (b) ethylene glycol.
A Pelton wheel is supplied with 6kg/s of water at 70m/s. The buckets rotate on a mean diameter of 350mm at 1200 rev/min. the deflection angle is 165º and friction negligible. a). Determine the diagram power.(5mks) b). Draw the vector diagram to scale and determine change in water velocity.(5mks)
The ram and plunger of a hydraulic press are 150 mm and 25 mm in diameter respectively. With a plunger stroke of 30 cm, the press is able to lift a load of 1 tonnes through 1.5 m in a times of 25 min. Area of the plunger
Diagram of the problem, necessary formulas, clearance and numerical solution What is the mass of 300 cm3 of lead (ρpb=12,000 kg/m3).
The dredger in Fig. P3.70 is loading sand (SG = 2.6) ontoa barge. The sand leaves the dredger pipe at 4 ft/s with aweight fl ow of 850 lbf/s. Estimate the tension on the mooringline caused by this loading process.