Water at 50 °F flows through a horizontal bend and discharges into the atmosphere as shown in the figure below. When the pressure gage reads p = 5 psi, the resultant x-direction anchoring force in the horizontal plane required to hold the bend in place, FAx, is equal to 1040 Ib. The flow is not frictionless. The areas A1 and A2 are 0.1 and 0.05 ft² respectively. Bend Q = ? → Water FAx A1 A2 FAy = ? 45° (a) Determine the flowrate through the bend. Q = i ft°/s (b) Find the y-direction anchoring force FAy, required to hold the bend in place. FAy = i Ib

Water at 50 °F flows through a horizontal bend and discharges into the atmosphere as shown in the figure below. When the pressure gage reads p = 5 psi, the resultant x-direction anchoring force in the horizontal plane required to hold the bend in place, FAx, is equal to 1040 Ib. The flow is not frictionless. The areas A1 and A2 are 0.1 and 0.05 ft² respectively. Bend Q = ? → Water FAx A1 A2 FAy = ? 45° (a) Determine the flowrate through the bend. Q = i ft°/s (b) Find the y-direction anchoring force FAy, required to hold the bend in place. FAy = i Ib

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When gage A indicates a pressure of 100 kPa gage, then cavitation just starts to occur in the venturi meter. If D = 40 cm and d = 10 cm, what is the water discharge in the system for this condition of incipient cavitation? The atmospheric pressure is 100 kPa gage, and the water temperature is 21°C. Neglect gravitational effects.
a 2.5 inch fire hose discharge a 1.25 inch jet. If the head lost in the nozzle is 6 ft, what gage pressure must be maintained at the base of the nozzle to throw a stream to a vertical height of 100 ft, neglecting air resistance? *please include its figure
A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameterd1 of 200 mm to a diameter d2 of 100 mm at the upper end. Oil of relative density 0.9 flowsthrough the pipe at a mean velocity ?̅1 at the lower end of 2 m/s. Find the pressure differenceacross the 2 m length ignoring any loss of energy, and the difference in level that would beshown on a mercury manometer connected across this length. The relative density of mercury is 13.6 and the leads to the manometer arefilled with the oil.
Water flows steadily through a horizontal 30 degree pipe bend. At the inlet point 1, the diameter is 0.3 m, the velocity is 12 m/s, and the pressure is 128 kPa gauge. At the outlet point 2, the diameter is 0.38 m and the pressure is 145 kPa gauge. Determine the forces F_x and F_y necessary to hold the pipe stationary.
2.48 The plunger in the sketch moves at a constant speed of 2 fps. Estimate the force F necessary if there is leakage past the plunger. Assume no losses so that Bernoulli's equation may be used between the stagnant reservoir and the two exit areas. Solution: 44.7 lbs
A pipe AB carries water and tapers uniformly from a diameter of 10cm at A to 12cm at B over a length of 2 m. Pressure gauges are installed at A, B and also at C, the midpoint of AB. If the pipe centerline slopes upwards from A to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3 bar, respectively. (1 bar = 100 kPa). Illustrate the problem and show your complete solution.
A 150 mm horizontal waterline contracts abruptly to 75 mm diameter. A pressure gage 150 mm upstream from the contraction reads 34.5 kPa when the mean velocity in the 150 mm pipe is 1.5 m/s. What will pressure gages read 0.6 m downstream and just downstream from the contraction if the diameter of the vena contracta is 61 mm? Neglect pipe friction
Water flowing at 1.0 ft/s in a pipe passes into a constriction where area is one-tenth the normal pipe area. What is the decrease in water pressure in the constriction? The weight density of water is 62.4 lbs/ft^3. (Figure, Formula, Solution)
The liquid being lifted by the pump below is gasoline with specific weight γgasoline = 47 lb/ft3 and a vapor pressure of 9 psi (absolute). The local atmospheric pressure is patm = 12.5 psi (absolute). The friction head loss through the pipe from its entrance to the pump entrance at B is hf = V 2 /(2g) empirically, where the velocity in the pipe is V = 7 ft/s. What is the maximum allowed value of z without cavitation occurring at the pump entrance at B?
A pipe AB carries water and tapers uniformly from a diameter of 4" at A to 8" at B over a length of 6 ft. Pressyre gauges are installed at A, B and also at C, the midpoint of AB. If the pipe centerline slopes upwards from A to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3 bar, respectively. (1 bar = 14.5 psi) Illustrate the problem before answering the following questions: (a)determine the flow, in ft^3/s through the pipe at C neglecting all lossess. (1 bar = 14.5 psi) (b)determine the pressure in bars, recorded at C neglecting all losses.
If the pressure in a tank of oil (sp gr 0.85) is 376 kN/m2, what is the equivalent head (a) inmeters of oil; (b) in meters of water; (c) in meters of mercury? maintaining the liquid head h at 5.67 ft (d)to what pressure PA be raised in order to double the discharge?
Water flows through the 50 cm diameter pipe to which the static pressure gauge and mercury manometer (pitot tube) are connected. The specific gravity of mercury and water is 133.600 N / m3 and 9810 N / m3, respectively. Calculate the height difference on the manometer since the linear flow velocity of the water in the pipe is 4.5 m / s x =? (If used, gravitational acceleration g = 9.8 m / s2)