A turbo generator rotating mass has a moment of inertia of 555 hyls/ m2. It isdelivering 2500 kw at 1800 rpm. The load then suddenly increases to 2550 kw, thedeveloped steam power remaining unchanged. What is the resulting speed in rpmafter 10 seconds?3311.3813113.381O 1133.381O 1331.381

GivenI=555 hyles /m2Pd1=2500kWω1=1800 rpmPd2=2550 kWt=10s

A turbo generator rotating mass has a moment of inertia of 555 hyls/ m2. It i delivering 2500 kw at 1800 rpm. The load then suddenly increases to 2550 kv developed steam power remaining unchanged. What is the resulting speed in after 10 seconds? O 3311.381 O 3113.381 O 1133.381

A turbo generator rotating mass has a moment of inertia of 555 hyls/ m2. It i delivering 2500 kw at 1800 rpm. The load then suddenly increases to 2550 kv developed steam power remaining unchanged. What is the resulting speed in after 10 seconds? O 3311.381 O 3113.381 O 1133.381

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following data refer to a 12-cylinder, single-acting, two-stroke marine diesel engine:Speed: 150 rpmCylinder diameter: 0.8mStroke of piston: 1.2 mArea of indicator diagram: 5.5x 10-4 m2Length of diagram: 0.06 mSpring value: 147 MPa per mFind the net rate of work transfer from the gas to the piston in kW.
A flywheel absorbs 2500 ft-lb of energy at a coefficient of fluctuation of 0.10. The mean diameter of the flywheel is 72 inches. The weight of the arms and hub is 12 % of the rim weight. The mean rim speed is 80 fps. Consider the specific weight of the flywheel as γ = 0.26 lb/in3. A. Find the mean rpm of the rim. B. Determine the weight of the rim. C. What is the cross sectional area of the rim?
A test carried out on a one-cylinder engine that works based on the Otto cycle, gives the following data: moment of rotation or torque = 950N-m; mean effective pressure = 758kPa; inner diameter = 30cm: stroke = 32cm; spin speed = 320rpm; fuel consumption = 0.003 kg / sec; calorific value of fuel = 42000kJ / kg. Determine: a) The thermal efficiency of the motor; b) mechanical efficiency; c) the fuel limit per hour if it has a price of 18.5 pesos per liter. Its relative density is 0.82
Explain and compare the mechanical efficiency of two and four-stroke engines.
Round off 4 decimal, Powerplant subject A dynamometer test was done for one hour at steady load on a 6 cylinder diesel engine. It was found to use 42 kg of fuel having Q h = 42,000 J/g. Cylinder is 22.8 cm x 27 cm, 4 cycle type. Speed, 550 rpm and dynamometer torque at 27000 kg cm. Determine the brake power (KW) and the brake thermal efficiency (%).
Engine friction a) Explain what do these terms mean: fmep, mfmep, pmep, amep, imep, bmep b) Write the equation relating fmep to mfmep, pmep, and amep; c) Write the equation relating fmep to imep and bmep; d) At a given engine speed, the following parameters are obtained as follows: 1600 bmep kPa 228.45 fmep kPa 124.38 mfmep kPa 29.52 amep kPa Calculate the net indicated mean effective pressure at the same engine speed.
20. A regenerative braking system stores kinetic energy of a car so that it can be recovered when the vehicle resumes moving. One way to do this is to “store” the energy in a spinning flywheel. One such design uses a solid disk flywheel with moment of inertia 0.040 kg m2 and maximum rotation rate 45000 rpm. (a) What is the maximum energy storage? (b) In principle it could store the kinetic energy of a 1700 kg car moving at what speed before braking? (c) If this energy is used to start the car moving again in 10.0 s, what is the power output of the system?
2. A diesel engine with a stroke of 4.72 inches and a displacement of 5.9 liters develops a peak torque of 600 lbft at 1600 rpm. What is the average piston speed in feet per minute at peak torque?
A four-stroke, 12-cylinder diesel engine has a bore and stroke of 820 mm and 2020 mm, respectively, per cylinder. The brake mean effective pressure of each cylinder is 1.2 MPa and the engine rotates at 145 rpm. The brake thermal efficiency of the engine is 32%, the mechanical efficiency is 72% and the net calorific value of the diesel is 40.75 MJ/kg. 1. calculate the specific fuel consumption (kg/kWh) ? Answer to 3 decimal places. 2. calculate thefuel consumption (kg/h) ? Answer to 0 decimal place.
This most likely is made to be a probelm about mx''+bx'+kx=f(t) m = mass b = friction k = spring constant 4. A mass weighing four pounds stretches a spring 24 in. Suppose the mass is atequilibrium and is set into motion with a velocity of 6 inches per second. The mass is in a mediumwhere friction is small, and we assume it is zero. Note that the acceleration due to gravity near theearth’s surface where the experiment takes place can be taken as 32 ft/s2.(a) Suppose that in addition to the conditions described above, a hammer strikes the mass everyπ/2 seconds starting at t = 0. A delta function with impulse of 1 pound-second models theforce of each blow to the mass. Find the function x(t) for the displacement from equilibrium infeet of the mass at time t in seconds. Express x(t) as a piecewise defined function without the use ofunit step or Heaviside functions and such that in each time window it is a different multiple of the samesinusoidal function.(b) Now assume the same spring-mass…
A diesel engine has a clearance volume of 35cc, displacement volume of 1000cc and the volume after combustion of 73cc. Calculate the theoretical thermal efficiency of the cycle.
(1) the brake power delivered (bp) = 104.846 Kw(2) the brake mean effective pressure (bmep) = 6.867 bar (3) the brake specific fuel consumption (bsfc) = 0.25179 kg/kwhr(4) the brake specific air consumption (bsac) = 3.433kg/kw.h(5) the brake thermal efficiency (b, th) = 32.4%(6) the volumetric efficiency (vol),= 56. 39%(7) the air-fuel ratio (A/F) on mass basis = 13.63Draw the simplified schematic diagram of the plant showing all the necessary data displayed on it. "Please only draw on schematic diagram of the plant"