A two-tier system to repair bridges is supported by two steel cables for each platform. Lengths of the cables are la = 55 in. and lp = 180 in. Assume that two 160 lb workers are going to be standing on the system to repair a bridge. one on each platform. The following design requirement must be met: the stretch of each cable must be less than 0.01 in. at the worst-case loading condition for each cable.

A two-tier system to repair bridges is supported by two steel cables for each platform. Lengths of the cables are la = 55 in. and lp = 180 in. Assume that two 160 lb workers are going to be standing on the system to repair a bridge. one on each platform. The following design requirement must be met: the stretch of each cable must be less than 0.01 in. at the worst-case loading condition for each cable.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the width and thickness of the leaves (in mm) of a leaf spring using the following specifications: Total load = 140 kN; Number of springs supporting the load = 4; Maximum number of leaves = 10; Span of the spring = 1000 mm; Permissible deflection = 80 mm; Modulus of elasticity, E = 200 kN/mm2; and allowable stress in spring material is 600 MPa.
A 5.0m long steel wire has a cross-sectional area of 0.55cm^2. Its proportional limit has a value of 0.0018 times its Young's modulus. Its breaking stress has a value of 0.0065 times its Young's modulus. The wire is fastened at its upper end and hangs vertically. a. How great a weight can be hung from the wire without exceeding the proportional limit? b. How much will the wire stretch under this load? c. What is the maximum weight that the wire can support?
Coefficients of Static Friction: Steel on Rope: 0.3 Try to pull an Acme brand safe off of a stone cliff and onto the bird. The safe is made of steel, measures 24”W x 30”H, and weighs 282 lbs. How much force is required to slide the safe?
A load of F = 14kN is applied to a circular chain link in the figure. Since σem = 600 N / mm2What is the diameter of the chain link in order to safely carry the given load?
Question 2 A load of 1.8 kN is hoisted by means of a rope on a lifting machine with a rotational frequency of 40 revolutions per min, and a drum whose diameter is 600 mm. Calculate the following: a) The power required for the load. b) Efficiency of the lifting machine, if an electric motor of 8kW is required to drive the lifting machine.
A machine component is subjected to a flexural mean stress of 88 MN/m2 and variable stress of 240 MN/m2. Take yield strength = 0.55 Ultimate strength; Endurance strength = 0.5 Ultimate strength; and factor of safety = 2. Compute and choose the nearest value of minimum ultimate strength according to Gerber relation. a. 630 MN/m2 b. 870 MN/m2 c. 991 MN/m2 d. 1093 MN/m2 Clear my choice
Prob # 1.A round bar made from SAE 1025 low Carbon steel is to support a direct tension load of 50,000 lbs. Using a factor of safety of 4, and assuming that the stress concentration factor, k = 1, What is the suitable standard diameter. Yield stress is 40,000 psi. a. 3 ½ inch b. 2 ¼ inch c. 2 9/16 inch d. 1 ½ inch
A circular bar of L 570mm length is supported freely at its two ends. It is acted upon by a central concentrated cyclic load having a minimum value of 20 kN and a maximum value of 50 kN. Take factor of safety of l.5, size effect of 0.85, and a surface finish factor of 0.9 . The material properties of bar are given as ultimatestrength of σu 625MPa, yield strength of σy 510MPa and endurance strength of σe 340MPA. Determine the diameter of bar by using Goodman's method and Soderberg method.
Evaluate and identify nearest value of the load that can be lifted to a height of 1000 cm in 0.50 minutes by a machine which has an input power of 0.65kW. a. Approximately 0.3 ton. b. Approximately 0.6 ton. c. Approximately 0.2 ton. d. Approximately 0.4 ton.
A 20 mm thick flange coupling connects two shafts in order to transmit 250 kW at 100 rpm. It uses 6 bolts with a diameter of 20 mm located at a 210 mm bolt circle diameter. Determine the factor of safety based on compression between the bolt and flange. The yield point of the bolt is 450 MPa. A. 4.75 B. 3.75 C. 2.75 D. 5.75
Select all true statements regarding the effect of the steel moment arm, gamma, on normalized P-M interaction diagrams. a. As gamma increases, the column flexural strength capacity increases b. As gamma increases, the column flexural strength capacity decreases c. As gamma increases, the column axial strength capacity increases d. As gamma increases, the column axial strength capacity decreases
3) A flange coupling is to connect two 60mm shafts. The hubs of the coupling are 120mm, 100mm thick, & the flange webs are 20 mm thick. Six M16 bolts fasten the flange from a 165 bolt circle. The keyway is 15mm shorter than the hub’s thickness & the key is 15mm x 15mm. The coupling transmits 45kW @ 450rpm. The yield point in shear for all materials is half of its yield point in tension or compression. Yield tensile strength is 0.75 of ultimate strength of the materials. The Sult is 448N/mm2 . Find: (a) the shear stress in key; (b) the bearing stress in key; (c) the shear stress in bolts; (d) bearing stress in flange.