A uniform beam of weight 12 N and length 10 m is mounted by a small hinge on a wall. The beam is held in a horizontal position by a vertical rope at the location as shown. What is the hinge force on the beam? 6.0 m O 27 N, up O 27 N, up O zero O 3.0 N, up O 3.0 N, down O 12 N, up O 12 N, down

A uniform beam of weight 12 N and length 10 m is mounted by a small hinge on a wall. The beam is held in a horizontal position by a vertical rope at the location as shown. What is the hinge force on the beam? 6.0 m O 27 N, up O 27 N, up O zero O 3.0 N, up O 3.0 N, down O 12 N, up O 12 N, down

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section: Chapter Questions

Problem 74A

See similar textbooks

Related questions

Q: A 35.4 kg beam is attached to a wall with a hinge and its far end is supported by a cable. The angle…

Q: The figure shows a uniform beam (m = 1200 kg) that extends beyond its support like a diving board.…

A: Distance between B and CG is 5 m Taking moment about the farthest right point…

Q: Determine the magnitude of force at the pin A and in the cable BC needed to support the 500-lb load.…

Q: The cantilevered beam is supported at the fixed support A as shown in Figure Q3.1. 6 kN 130 1 30°…

Q: A uniform horizontal beam with a length of 9.3 m and a weight of 234.9 N is attached to a wall by a…

A: Given:- A uniform horizontal beam with a length ofL= 9.3 m a weight of 234.9 N is attached to a…

Q: The following figure shows a 4 m bar attached to the wall through a hinge that rotates freely, but…

Q: A diving board 3.00 m long is supported at a point 1.00 m from the end, and a diver weighing 500 N…

Q: The following figure shows a 4 m bar fixed to the wall through a hinge that rotates freely, but is…

Q: A 350 N uniform boom is supported by a perpendicular cable attached at 0.7 its length from the…

Q: A uniform beam of weight 100N is pivoted at P as shown. Weights of 10 N and 20 N are attached to its…

Q: What are the forces applied to the board by the posts?

A: the values provided in the question are as follows- mass of board = 34 kg length of board = 4.7m…

Q: A gymnast with mass 46.0 kg stands on the end of a uniform balance beam as shown in the figure. The…

A: Concept Apply the torque concept Torque=Distace*Force

Q: A door has a height of 2.2 m along a y axis that extends vertically upward and a width of 0.803 m…

Q: Suppose the weight of the drawbridge in the figure is supported entirely by its hinges and the…

Q: A 10 m ladder with a mass of 15 kg leans against the wall. If the ladder is in static equilibrium,…

A: We have a ladder of length L=10 m having mass M=15 kg which leans on a frictionless wall. Assuming…

Q: A worker of weight 756.5 kg stands on the end of a beam of weight 1699 N and length L= 118.7 m,…

A: Given Mass of worker =756.5kg Weight of beam =1699N L=118.7m X=26.7m

Q: 18 D. From the step ladder shown in the figure, sides AC and CE are each 2.44 m long and hinged at…

Q: 5.00 m 3.00 m 4.00 m 300 N 6. The horizontal beam in the figure weighs 150 N, and its center of…

A: Net torque on the beam about hinge is zero. Mg×4 + mg×2 = T( Sin37) × 4 Given Mg = 300 N mg = 150 N…

Q: A uniform platform with mass M=30kg and length L=15m is placed on two supports as shown. The…

A: A mass of a uniform platform,

Q: Two people, let’s call them person A and person B, carry a uniform board of length 6 meters and…

A: DataLength, L = 6mWeight, W = 150NDistance of A from end 1, a=1mDistance of B from end 2, b=2m…

Q: From the step ladder shown in the figure, sides AC and CE are each 2.44 m long and hinged at point…

Q: A diving board 3.00 m long is supported at a point 1.00 m from the end, and a diver weighing 500 N…

Q: Auniform ladder is 16 m long and weighs 180 N. In the figure, the ladder leans against a vertical,…

A: According to our answering policies, I can answer only first three subparts of this question. The…

Q: A pole is attached to a wall with a hinge as shown. A sign is suspended at the other end of a pole,…

Q: In the figure, one end of a uniform beam of weight 130 N is hinged to a wall; the other end is…

A: Given that: W=130 Nθ=31°

Q: A uniform beam is 5.0 m long and is supported as shown in the figure. At the center of the beam, a…

A: Given, m1= 12g m2= 10g m3= ? Torque due to tension = 1300 Mass of beam M= ? Length of beam (L)= 5m

Q: An 8-m board of negligible weight is supported at a point 2 m from the right end, where a 50-N…

A: Length of board (L) = 8 m Pivot point = 2 m from right end First weight (w) = 50 N (at right end)…

Q: A horizontal plank 4.64 m long and having mass 23.0 kg rests on two pivots, one at the left end and…

Q: Determine the magnitude P of the vertical force required to lift the wheelbarrow free of the ground…

A: Balance torque about point O would give us the value of P required to lift the cart from point B

Q: A uniform beam of weight 19 N and length 6.0 m is mounted by a small hinge on a wall at it left end.…

Q: In the figure, suppose the length L of the uniform bar is 2.7 m and its weight is 180 N. Also, let…

A: (a) Maximum possible distance X= 0.825 m (b) Fx = 350 N (c) Fy = 326 N

Q: In the figure, suppose the length L of the uniform bar is 3.1 m and its weight is 240 N. Also, let…

A: We will calculate the torques exerted on the system around the hinge. a) Calculate the torque…

Q: The following uniform beams are pivoted about their center of mass. Which of them is in static…

Q: A man is attempting to raise a 7.5 m long, 28 kg flagpole that has a hinge at the base by pulling on…

A: If a rigid body is in equilibrium, the vector sum of all force acting on the body is zero,

Q: A uniform plank of length L=2.7m and weight W =735N is supported by three ropes as indicated in the…

A: Given information: The symbols have the same meaning as given in the question.

Q: A diving board 3.00 m long is supported at a point 1.00 m fromthe end, and a diver weighing 500 N…

Q: The boom AB supports a load of W = 720 lb. The boom is supported by a ball-and-socket joint at A and…

A: In this question we are given with a figure and we have to find the tension in each cable and axial…

Q: A fulcrum is placed 1.0 m from the edge of a 3.0 m-long wooden uniform plank of mass 20 kg. A weight…

Q: In the figure, one end of a uniform beam of weight 440 N is hinged to a wall; the other end is…

Q: A UNIFORM ROD OF LENGTH 3M AND WEIGHT 100N WITH ENDS A AND B RESTING ON TWO BRACKETS, BEARS 50N…

A: The diagram is drawn below.

Q: A uniform 400 N beam of length L = 4 m is supporting a 2000 N box as shown. Find the tension in the…

Q: 1. A0.5 kg uniform meter stick is hinged at 0.5 cm from one end and held horizontally by a force T…

A: 1) a) Analyze the following figure. As the stick is held stationary, the net torque acting on the…

Q: A father and his son are supposed to carry a load of 500 N. They decided to use a pole (of uniform…

Q: A weightless strut, hinged to a wall, is used to support a 200.0 N block as shown. The horizontal…

A: Given data: Weight of the block, W=200 N

Q: As shown in the figure, a 10 m long bar is attached by a frictionless hinge to a wall and held…

A: Given: The length of the rod is 10 m. The weight of the rod is 66.5 N. The tension in the rope is…

Q: A bridge of length l smooth pier at each end as shown in the figure below. A truck of mass m = d =…

Q: A uniform rod of weight 5 N and length 1 m is pivoted at a point 20 cm from one of its ends. A…

A: Write the expression for moment.

Q: A weightless strut, hinged to a wall, is used to support a 200.0 N block as shown. The horizontal…

A: Given: A weightless strut, hinged to a wall, is used to support a 200 N block. To determine: The…

Q: A uniform beam of mass 11.0 kg and length 1.10 m is suspended by a rope attached at a distance x =…

Concept explainers

Center of Gravity of a system

The centre of gravity is a property that is based on the geometry of a rigid body or any particle. It is described as an equilibrium point or a hypothetical location where the total weight of the body is concentrated.

Question

A uniform beam of weight 12 N and length 10 m is mounted by a small hinge on a wall. The beam is held in a horizontal position by a vertical rope at the location as shown. What is the hinge force on the
beam?
6.0 m
O 27 N, up
O 27 N, up
O zero
O 3.0 N, up
O 3.0 N, down
O 12 N, up
O 12 N, down

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

The uniform seesaw shown below is balanced on a fulcrum located 3.0 m from the left end. The smaller boy on the right has a mass of mass of 40 kg and the bigger boy on the left has a mass 80 kg. What is the mass of the board?
Find the magnitude of the tension in each supporting cable shown below. In each case, the weight of the suspended body is 100.0 N and the masses of the cables are negligible.
In order to get his car out of the mud, a man ties one end of a rope to the front bumper and the other end to a tee 15 m away as shown below. He then pulls on the center of the rope with a force of 400 N, which causes its center to be displaced 0.30 m, as shown. What is the force of the rope on the car?
A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.
Check Your Understanding A 400.0-N sign hangs from the end of a uniform strut. The strut is 4.0 m long and weighs 600.0 N. The strut is supported by a hinge at the wall and by a cable whose other end is tied to the wall at a point 3.0 m above the left end of the strut. Find the tension in the supporting cable and the force of the hinge on the strut.
Under what conditions can a rotating body be in equilibrium? Give an example.
When tightening a bolt, you push perpendicularly on a wrench with a force of 165N at a distance of 0.140m from the center of the bolt. How much torque are you exerting relative to the center of the bolt?
Problems 33 and 34 are paired. One end of a uniform beam that weighs 2.80 102 N is attached to a wall with a hinge pin. The other end is supported by a cable making the angles shown in Figure P14.33. Find the tension in the cable. FIGURE P14.33 Problems 33 and 34.
If an odd number of forces act on an object, the object cannot be in equilibrium.
Is it possible to rest a ladder against a rough wall when the floor is frictionless?
A uniform plank of length 2.00 m and mass 26.0 kg is supported by three ropes, as indicated by the blue vectors in the figure below. Find the tension in each rope when a 710–N person is d = 0.500 m from the left end. Answer the 3 boxes below:
One end of a uniform beam that weighs 3.50 ✕ 102 N is attached to a wall with a hinge pin. The other end is supported by a cable making the angles shown in the figure below. Find the tension in the cable. (Assume ?1 = 20° and ?2 = 37°.) Note: The answer is 244 N but I have no idea how to get there. Any help would be appreciated. Thanks.