A uniform cantilever beam weighing 750-N has a smooth turning pulley attached to its free end. The pulley's mass is negligible compared to the beam's mass and may be ignored. As shown, the beam is loaded by a 1000-N block suspended by a wire rope passing over the pulley B and attached to a vertical wall.

A uniform cantilever beam weighing 750-N has a smooth turning pulley attached to its free end. The pulley's mass is negligible compared to the beam's mass and may be ignored. As shown, the beam is loaded by a 1000-N block suspended by a wire rope passing over the pulley B and attached to a vertical wall.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A small balcony constructed of wood issupported by three identical cantilever beams (seefigure). Each beam has length L1 = 2.1m, width b,and height h = 4b/3. The dimensions of the balconyfloor are L1 XL2, where L2 = 2.5 m. The designload is 5.5 kPa acting over the entire floor area.(This load accounts for all loads except the weightsof the cantilever beams, which have a weight densityΥ = 5.5 kN/m3.) The allowable bending stress in thecantilevers is 15 MPa.Assuming that the middle cantilever supports50% of the load and each outer cantilever supports25% of the load, determine the required dimensions band h.
A beam of rectangular section of 12 cm × 20 cm is simply supported over a span of 12 m. It is acted upon by a load of 80 kN at the mid span. Determine the maximum bending stress induced in thr beam.
A cable with supports at the same elevation has a span of 300m. The cable weighs 75 N/m and the sag at midspan is 75 m. Determine The length of the cable.
The beam safely supports shear forces and bending moments of 2kN and 6.5 kN-m respectively. Based on this criterion, can it be safely subjected to the loads F = 1kN and C = 1.6 kN-m?
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 5.0 ft, b = 3.4 ft, P = 25 kips, and w = 1.1 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Considering a uniform beam of 1 m long simply supported at both ends, theBending moment is given by the following relation:
A uniform beam that 10-m long is being supported by two men, one man at each end. The weight of the beam. Is 100-N. If the first man supporting at the right side exert twice as much as the second man on the left, where must a 50-N motor be placed (measured from the first man) on top of the beam? Show complete solution.
Ancient pyramid builders are balancinga uniform rectangular stoneslab of weight w, tipped at anangle u above the horizontal, usinga rope (Fig.). The rope isheld by five workers who share theforce equally. (a) If u = 20.0°, whatforce does each worker exert on therope? (b) As u increases, does eachworker have to exert more or lessforce than in part (a), assuming theydo not change the angle of the rope? Why? (c) At what angle do theworkers need to exert no force to balance the slab? What happens if uexceeds this value?
a)??? b) left to the point of application of force P. The cross sectional area of the beam is 300 cm2 tgroughout the beam.
Draw the shear and Bending moment diagram of each beam below using the equation method and area method. CHANGE 20 kN/m to 33 kN/m
The figure below demonstrates a beamsimply supported, subjected to a loadfixed1177 kn Considering the value of L = 6m, obtainthe diagrams of (a) shear force and (b)bending moment for this beam with thisloading.
A 70kg human steps at the tip of a springboard used to dive in a pool. The springboard has a length of 1.75 meters, moment of inertia is 0.000002 m^4, and modulus of elasticity is 150 GPa. Determine the deflection of the springboard in millimeters. Note: δ=[(W)(L^3)]/[(3)(E)(I)] for a cantilever beam with end force.