Assignment - Band Brakes The figure depicts a band brake whose drum rotates counterclockwise at 200 rev/min. The drum diameter is 16 in and the band lining 3 in wide. The coefficient of friction is 0.20. The maximum lining interface pressure is 70 psi. Find the: (a) Brake torque, ft-lbf (b) Necessary force P, Ibf (c) Heat generated, Btu/ min d) Lining pressure (psi) at both ends of the contact arc. Designate your answers as Pmax and Pmin 3 in 10 in

Assignment - Band Brakes The figure depicts a band brake whose drum rotates counterclockwise at 200 rev/min. The drum diameter is 16 in and the band lining 3 in wide. The coefficient of friction is 0.20. The maximum lining interface pressure is 70 psi. Find the: (a) Brake torque, ft-lbf (b) Necessary force P, Ibf (c) Heat generated, Btu/ min d) Lining pressure (psi) at both ends of the contact arc. Designate your answers as Pmax and Pmin 3 in 10 in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The cylinder bore diameter of a single-acting reciprocating pump is 150 mm and its stroke is 310 mm. The pump runs at 56 rpm and lifts water through a height of 28 m. The delivery pipe is 23 m long and 102 mm in diameter. Find (i) the theoretical discharge in liters/s,(ii) the theoretical power required to run the pump in kW, (iii) the percentage of slip, and (iv) the coefficient of discharge., if the actual discharge is 4.3 liters/s. Assume the weight density of water is 9810 N/m3
The cylinder bore diameter of a double-acting reciprocating pump is 170 mm and its stroke is 370 mm. The pump runs at 55 rpm and lifts water through a height of 26 m. The delivery pipe is 23.5 m long and 113 mm in diameter. Find (i) the theoretical discharge in liters/s,(ii) the theoretical power required to run the pump in kW, (iii) the percentage of slip, and (iv) the coefficient of discharge., if the actual discharge is 13 liters/s. Assume the weight density of water is 9810 N/m3 (i)Theoretical discharge in liter/s (ii) the theoretical power required to run the pump in kW (iii) the percentage of slip (iv) the coefficient of discharge.
The cylinder bore diameter of a double-acting reciprocating pump is 160 mm and its stroke is 340 mm. The pump runs at 53 rpm and lifts water through a height of 29 m. The delivery pipe is 22 m long and 100 mm in diameter. Find (i) the theoretical discharge in liters/s,(ii) the theoretical power required to run the pump in kW, (iii) the percentage of slip, and (iv) the coefficient of discharge., if the actual discharge is 10 liters/s. Assume the weight density of water is 9810 N/m3
A cone clutch is to transmit 7.5 kW at 900 rpm. The cone has a face angle of 12o. The width of the face ishalf of the mean radius and the normal pressure between the contact faces is not exceeding0.09Nmm2⁄. Assuming uniform wear and the coefficient friction between contact faces as 0.2. Find themain dimensions of the clutch and the axial force required to engage the clutch.
The values given for a radial plain bearing are:Shaft diameter = 40 mm, bearing width = 30 mm, Pem = 6 N / mm2, Radial force = 2 KN, Ty = 45 C, oil: ISO VG 15, bearing clearance = 35 µm, dynamic viscosity for given oil and temperature = 12 m Pa. sRequired:a) What is the working cycle of the shaft?b) Find the Sommerfeld number.
1. For a given pump, the diameter, the gauge pressures at the inlet and outlet are −30 × 103 P a and 200 × 103 P a, respectively. If the flow rate is 0.1 m3/s, and the power required is 25 kW, find the efficiency. The intake and discharge are at the same height. 2. The impeller of a radial-flow turbine has an outer radius of 4 f t, turning at 200 rpm. The volume flow rate is 1000 ft3/s, and it discharges in the axial direction. Neglect all losses. If the tangential component of the velocity at the inlet is 5 f t/s, find: (a) The torque exerted on the impeller. (b) The power developed by the machine.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.
A pump has a displacement of 90 cm3 . It delivers 75 Lpm at 1300 rpm and 75 bar .If the prime mover torque is 90 N-m. What is the theoritical troque required to operate the pump? a. 107.48 N-m b. 75 N-m c. 120.54 N-m d. 90 N-m
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.
A standard cylinder receives 10 gpm from a pump at 2000 psi. The cylinder bore is 3 in. and therod diameter is 1.5 in. Find: • For extension, the flow in, flow out, speed, and force. • For retraction, the flow in, flow out, speed, and force
Determine the principal dimensions of a cone clutch faced with lather to transmit 40 kW at 800 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions. Assume that the semi-angle of the cone is 10°, the coefficient of friction is 0.3, mean diameter of cone is (7-10)d, where d is the diameter of the shaft, allowable normal pressure for lather and cast iron is 0.1 to 0.2 N/mm, shear stress 100 N/mm², load factor is 2 and the mean diameter to face width ratio is 6.
The following particulars refer to a 4-cylinder, 4-stroke petrol engine; Bore= 65 mm, Stroke length = 95 mm, Torque developed = 64 Nm when engine turns 3000 rev/min, Clearance volume = 63 cm3 for each cylinder, Relative efficiency = 0.5 and Calorific value of petrol = 42000 kj/kg. Make calculations for brake mean effective pressure and the fuel consumption in kg/hr.