A uniform ladder of length L and mass m1 rests against a frictionless wall. The ladder makes an angle theta with the horizontal. Find the horizontal and vertical forces the ground exerts on the base of the ladder when a firefighter of mass m2 is a distance of x along the ladder from the bottom. Use any variable or symbol above along with the following as necessary: g

A uniform ladder of length L and mass m1 rests against a frictionless wall. The ladder makes an angle theta with the horizontal. Find the horizontal and vertical forces the ground exerts on the base of the ladder when a firefighter of mass m2 is a distance of x along the ladder from the bottom. Use any variable or symbol above along with the following as necessary: g

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 32P

See similar textbooks

Similar questions

A horizontal beam of length 4.08m and weight 130N is attached to a vertical wall at a right angle. There is also a support wire of length 5.04m which attaches the far end of the beam to the wall from above. Off of the far end of the beam also hangs an object of weight 330 N. (a) What is the magnitude of the tension in the support wire? (b) What is the horizontal component of the force exerted on the beam at the wall? (c) What is the vertical component of the force exerted on the beam at the wall?
Multiple-choice question: As shown in the figure, both the vertical wall and the fixed slope are smooth, then the magnitude of the force acting on the slope by a ball with mass m
a diver of weight 580 N standing at the end of a diving board with a length of L =4.5 m and negligible mass. The board is fixed to two pedestals (supports) that are separated by distance d = 1.5 m. Of the forces acting on the board, what are the (a) magnitude and (b) direction (up or down) of the force from the left pedestal and the (c) magnitude and (d) direction (up or down) of the force from the right pedestal? (e) Which pedestal (left or right) is being stretched, and (f) which pedestal is being compressed?
Some insects can walk below a thin rod (such as a twig) by hanging from it. Suppose that such an insect has mass m and hangs from a horizontal rod with angle u = 40. Its six legs are all under the same tension, and the leg sections nearest the body are horizontal. (a) What is the ratio of the tension in each tibia (forepart of a leg) to the insect’s weight? (b) If the insect straightens out its legs somewhat, does the tension in each tibia increase, decrease, or stay the same?
One end (A) of a thin rod rests on a floor, with coefficient of static friction μs. The other end (B) of the rod leans against a frictionless wall. The rod has a length of L and a mass of m. The rod has a uniform density, so the center-of-mass is a distance L/2 from either end. The rod does not move. variables only (m, g, L, θ, μs) a) Draw a free body diagram for the rod clearly showing all forces and where they are applied. Hint: There are four forces! b) On your diagram, draw and label the line of action and lever arm for the weight force about point A. c) What is the torque produced by the weight force about point A? d) Using static equilibrium equations, find the three support forces (two at A, one at B). e) Given the coefficient of static friction μs, what is the smallest possible angle before the rod starts to move?
Write an expression for the magnitude of the normal force, F N acting on the block, in terms of F2, g, and the other variables of the problem. Assume that the surface it rests on is rigid.
A cubical box is filled with sand and weighs 890 N.We wish to “roll” the box by pushing horizontally on one of the upper edges. (a) What minimum force is required? (b) What minimum coefficient of static friction between box and floor is required? (c) If there is a more efficient way to roll the box, find the smallest possible force that would have to be applied directly to the box to roll it. (Hint: At the onset of tipping, where is the normal force located?)
A construction worker attempts to lift a uniform beam off the floor and raise it to a vertical position. The beam is 2.50 m long and weighs 500 N. At a certain instant the worker holds the beam momentarily at rest with one end at distance d =1.50 m above the floor, , by exerting a force on the beam, perpendicular to the beam. (a) What is the magnitude P? (b) What is the magnitude of the (net) force of the floor on the beam? (c) What is the minimum value the coefficient of static friction between beam and floor can have in order for the beam not to slip at this instant?
A construction worker attempts to lift a uniform beam off the floor and raise it to a vertical position. The beam is 1.88 m long and weighs 490 N. At a certain instant the worker holds the beam momentarily at rest with one end a distance d = 1.02 m above the floor, as shown in the figure, by exerting a force P→ on the beam. (a) What is the magnitude of P→? (b) What is the magnitude of the (net) force of the floor on the beam? (c) What is the minimum value the coefficient of static friction between beam and floor can have in order for the beam not to slip at this instant?
A uniform rod with a weight W= 100 N and a length L = 2.0 m is hinged at the bottom end and is vertical. A light cable, tied to the rod at a height of h = 1.0 m, makes an angle 0 = 40° from the horizontal. A horizontal force F= 50 N is exerted at a height H = 1.5 m on the rod. (a) Draw a free-body diagram for the rod.(b) What is the tension in the cable?(c) What are horizontal and vertical components ofthe force exerted on the rod at the hinge?
As shown on the right, a uniform rod with a weight W= 100 N and a length L = 2.0 m is hinged at the bottom end and is vertical. A light cable, tied to the rod at a height of h = 1.0 m, makes an angle 0 = 40° from the horizontal. A horizontal force F= 50 N is exerted at a height H = 1.5 m on the rod. (a) Draw a free-body diagram for the rod.(b) What is the tension in the cable?(c) What are horizontal and vertical components ofthe force exerted on the rod at the hinge?
A man stands a distance d = 0.275 m from the left end of a platform as shown in the figure. The platform is supported by three cables. Find the tension in each cable (in N). Assume the platform is uniform, with length L = 2.00 m and mass 35.0 kg, and the weight of the man is 690 N. (Due to the nature of this problem, do not use rounded intermediate values in your calculations—including answers submitted in WebAssign.) (b). What If? The man now begins to walk to the right. If each of the cables can support a maximum tension of 800 N, which cable fails first? At what location does this occur (measured in m from the left end of the platform)?