A uniformly distributed load of 226 Ib/ft is carried by a simply supported beam span. The beam is a hollow rectangular section, having a width, b = 4.8 inches, height, h = 5.7 inches and constant wall thickness of 2.6 inches. Determine the first moment of area, Q of the beam in mm^3 at the point of maximum shearing stress.

A uniformly distributed load of 226 Ib/ft is carried by a simply supported beam span. The beam is a hollow rectangular section, having a width, b = 4.8 inches, height, h = 5.7 inches and constant wall thickness of 2.6 inches. Determine the first moment of area, Q of the beam in mm^3 at the point of maximum shearing stress.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.6.13P: A two-axle carriage that is part of an over head traveling crane in a testing laboratory moves...

See similar textbooks

Similar questions

A simple beam with a W 10 x 30 wide-flange cross section supports a uniform load of intensity q = 3.0 kips/ft on a span of length L = 12 ft (sec figure). The dimensions of the cross section are q = 10.5 in., b = 5.81 in., t1= 0.510 in., and fw = 0.300 in. Calculate the maximum shear stress tjuly on cross section A—A located at distance d = 2.5 ft from the end of the beam. Calculate the shear stress rat point Bon the cross section. Point B is located at a distance a = 1.5 in. from the edge of the lower flange.
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h = 120 mm and h1= 100 mm. The maximum allowable bending stress in the plastic beam is emix = 6 M Pa, and the bending moment is M = 150 N · m. Determine the minimum permissible width bminof the beam.
A frame ABCD is constructed of steel wide-flange members (W8 x 21; E = 30 x ID6 psi) and subjected to triangularly distributed loads of maximum intensity q0acting along the vertical members (see figure). The distance between supports is L = 20 ft and the height of the frame is h = 4 ft. The members are rigidly connected at B and C. Calculate the intensity of load q0 required to produce a maximum bending moment of 80 kip-in. in the horizontal member BC. If the load q0 is reduced to one-half of the value calculated in part (a), what is the maximum bending moment in member BC? What is the ratio of this moment to the moment of 80 kip-in. in part (a)?
.2 A ligmio.irc ii supported by two vorlical beams consistins: of thin-walled, tapered circular lubes (see ligure part at. for purposes of this analysis, each beam may be represented as a cantilever AB of length L = 8.0 m subjected to a lateral load P = 2.4 kN at the free end. The tubes have a constant thickness ; = 10.0 mm and average diameters dA = 90 mm and dB = 270 mm at ends A and B, re s pec lively. Because the thickness is small compared to the diameters, the moment of inerlia at any cross section may be obtained from the formula / = jrrf3;/8 (see Case 22, Appendix E); therefore, the section modulus mav be obtained from the formula S = trdhlA. (a) At what dislance A from the free end docs the maximum bending stress occur? What is the magnitude trllul of the maximum bending stress? What is the ratio of the maximum stress to the largest stress (b) Repeat part (a) if concentrated load P is applied upward at A and downward uniform load q {-x) = 2PIL is applied over the entire beam as shown in the figure part b What is the ratio of the maximum stress to the stress at the location of maximum moment?
Two identical, simply supported beams AB and CD are placed so that they cross each other at their midpoints (sec figure). Before the uniform load is applied, the beams just touch each other at the crossing point. Determine the maximum bending moments (mab)max* and (MCD)max beams AB and CD, respectively, due to the uniform load if the intensity of the load is q = 6.4 kN/m and the length of each beam is L = 4 m.
A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h = 0,88 in. and h1 = 0.80 in. The maximum allowable bending stress in the metal beam is emax = 60 ksi, and the bending moment is M = 600 lb-in. Determine the minimum permissible width bminof the beam.
A beam of size 150 mm wide, 250 mm deep carries a uniformly distributed load of w kN/m over entire span of 4 m. A concentrated load 1 kN is acting at a distance of 1.2 m from the left support. If the bending stress at a section 1.8 m from the left support is not to exceed3.25 N/mm2 find the load w.
A beam having a tee-shaped cross section is subjected to equal 13 kN-m bending moments, as shown. Assume bf = 95 mm, tf = 25 mm, d = 165 mm, tw = 40 mm. The cross-sectional dimensions of the beam are also shown. Determine(a) the centroid location (measured upward from the bottom), the moment of inertia about the z axis, and the controlling section modulus about the z axis.(b) the bending stress at point H (positive if tensile and negative if compressive).(c) the maximum bending stress (positive if tensile and negative if compressive) produced in the cross section.
simply supported wood beam with overhang is subjected to uniformly distributedload q. The beam has a rectangular cross section with width b = 200 mm and height h= 250 mm. Determine the maximum permissible value q if the allowable bendingstress is eall= 11 MPa, and the allowable shear stress is Tall= 1.2 MPa.
A Simply supported beam of length 3 m, is subjected to an Uniformly distributed load of 28 kN/m for entire span. It has a hollow rectangular cross section of outer width 30 mm and outer depth of 80 mm with the wall thickness of 5mm. Find, (i) The maximum bending moment, (ii)Bending stress induced,
The structure shown below consists of a brass core inserted into a steel tube of cross section square. If a moment of 8 kN × m is applied at its end, determine the maximum bending stress in the bar. Elaton = 100 GPa, Steel = 200 GPa.