Draw the shear and moment diagram of the cantilever beam shown below. For this part, please show the necessary solutions using the long method, not the area moment method. Each correct line/curve with degrees equates to 1 pt. 10 kip 8 kip 3 kip/ft 40 kip-ft 6 ft 4 ft

Draw the shear and moment diagram of the cantilever beam shown below. For this part, please show the necessary solutions using the long method, not the area moment method. Each correct line/curve with degrees equates to 1 pt. 10 kip 8 kip 3 kip/ft 40 kip-ft 6 ft 4 ft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.10.17P

See similar textbooks

Related questions

Q: Calculate the shear force and bending moment for the simply supported beam of length 8m with the…

Q: A simply supported beam is loaded as shown. Consider left of an exploratory section between C and D,…

Q: Establish the Shear & Moment Equation and Diagram of the loaded beam shown. Consider the Left Body…

Q: Given an overhanging beam loaded as shown in the figure. 40 KN 30 KN/m 10 KN-m 3m 2 m 2 m 1.1.…

A: (1.1) Draw the free-body diagram.

Q: rt 1 For the simply supported beam subjected to the loading shown, derive equations for the shear…

Q: Determine the shear and moment equations throughout the beam. Using these equations, sketch the…

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

Q: 3 ft 100 lb B 5 ft CO 40 lb/ft Ꭰ 4 ft

A: Find the most critical point in the beam. Most critical point is the point where maximum bending…

Q: A simply supported beam of width 100 mm, height 200 mm and length 4 m is carrying a uniformly…

A: GIVEN DATA- A SSB GIVEN WITH UDL L=4m w=10KN/m b=100mm d=200mm WE HAVE TO FIND BENDING STRESS

Q: 5. Analyze the statically indeterminate beam by force method, and draw the bending moment diagram,…

Q: Draw Shear and Moment Diagrams for each of the beams below and find max bending stress. Every beam…

Q: a)A simply supported beam of length 6 m ,carries point load of 3 kN 4 m from the left end. Draw the…

Q: A simply supported beam of width 100 mm, height 200 mm and length 4 m is carrying a uniformly…

Q: For the simply supported beam subjected to the loading shown, sketch the shear force diagram.…

Q: The cantilever beam in Fig. (a) carries a triangular load, the intensity of which varies from zero…

Q: A cantilever beam 2m span carries point loads as shown. Draw the shear force and bending moment…

Q: Example: Draw Shear & Moment diagrams for the following beam 12 kN 8 kN А C В 1 m 3 m 1 m - RA = 7…

A: The free body diagram of the beam is given below,

Q: A beam segment subjected to internal bending moments at sections A and B is shown along with a…

Q: Calculate the shear force and bending moment for the simply supported beam of length 8m with the…

Q: Draw the shear and bending moment curves for the beam and loading and the maximum absolute value of…

Q: 10 kN/m |2m 2m 2m 6m 6m 2. A compound beam is pin connected at E and Fas shown above. a. Determine…

A: For solution refer below images.

Q: Using the coordinate axes shown, write equations for the shear V and bending moment M for any…

A: Draw the free-body diagram of the beam.

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

Q: A beam is partially loaded with a uniform load of 2 kN/m and a point load of 2 kN as shown below. i.…

A: RA+RB=2×3+2RA+RB=8 ......1And now taking moment about point A6×32+2×3-5RB=0RB=3KN And from equation…

Q: For the simply supported beam subjected to the loading shown, derive equations for the shear force…

A: removing the support and applying the reaction Applying the equilibrium equation ∑MD=0RB X 7.5-80…

Q: Determine the shear and moment equations throughout the beam. Using these equations, sketch the…

A: Draw shear force and bending moment diagram

Q: A beam is loaded and supported as shown in Fig. Using the coordinate axes shown, write equations for…

A: Given Data: The load per unit length is w = 500 lb/ft. The moment acting on the beam is M0 = 6000…

Q: Draw the shear and moment diagrams for the beam shown using moment distribution method. Loads and…

A: Given :-Beam with different loading and support conditionsTo find:-Shear and moment diagram

Q: Determine the shear and moment as functions of x and draw the shear and moment diagrams for the beam…

Q: Complete a Shear Force Diagram and a Bending Moment Diagram for the following: 12.75 kips 8.25 kips…

A: Given :- Simply Supported Beam AB with with point loads To Do:- Draw Shear Force Diagram and…

Q: Determine the following based on the diagram below Magnitude of the maximum shear force • Location…

Q: For the beam shown below, write the shear and moment equations for segment BC. 60 KN 40 KN/m A C…

Q: From the given beam shown below, find the shear value on segment BC (VBC). 40kr/m 75kum Тв ↓ Im +

A: Given data: w=40 kN/mM=75 kN.m Need to determine the shear force value in segment BC.

Q: A cantilever beam 2m span carries point loads as shown. Draw the shear force and bending moment…

Q: d kN kN/m The beam shown above has been supported at points A. Magnitude Your Student ID's last two…

Q: Use the AREA method to construct the shear-force and bending-moment diagrams for the beam shown. Let…

Q: Draw the shear and moment diagram of the cantilever beam shown below. For this part, please show the…

A: Consider upward force & CW moment as (+)ve and downward force & CCW moment as (-)ve. Let…

Q: For the simply supported beam subjected to the loading shown, derive equations for the shear force…

Q: (a) A simply supported beam of length 6 m carries point loads of 5 kN each at a distance of 1.5 m…

A: The beam explained in the problem can be sketched as follows,

Q: 53 KN (m 318KN 53KN/m 2m 2m f 1.5m 1.Sm 2m

A: For solution refer below images.

Q: 13. For the beam below provide the following information: a. Determine the shear and moment…

Q: Find the shear and moment equations for each segment (hint: 3 segments)of the figure shown Indicate…

A: To draw the shear force and bending moment diagrams associated to the question, we must first obtain…

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

Q: Let a=4 ft, b=6 ft, c=4 ft and w=7.5 kips/ft. Construct the shear-force and bending-moment diagrams…

Q: Draw the shear force and Bending Moment Diagram for the following beam. 25 KN 32 KN 17 KN 28 KN в 35…

Q: Q: Draw shear force and bending moment diagrams for the beam shown below and then find max. shear…

Q: Part 1 For the simply supported beam subjected to the loading shown, derive equations for the shear…

Q: Q1: For the square beam shown below, the cross section area is 100 in', a) Find the shear force and…

A: Given dataArea of square cross section A = 100in2Side length a = 10inModulus of elasticity E =…

Q: 2 kN/m B 2 m- 4 m

Q: For the simply supported beam subjected to the loading shown, derive equations for the shear force V…

Question

100%

Draw the shear and moment diagram of the cantilever beam shown below. For this part, please show the necessary solutions
using the long method, not the area moment method. Each correct line/curve with degrees equates to 1 pt.
10 kip
8 kip
3 kip/ft
40 kip-ft
6 ft
4 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The three beams shown have approximately the same cross-sectional area. Beam 1 is a W 14 X 82 with flange plates; beam 2 consists of a web plate with four angles; and beam 3 is constructed of 2 C shapes with flange plates. Which design has the largest moment capacity? Which has the largest shear capacity? Which is the most economical in bending? Which is the most economical in shear? Assume allowable stress values are: = 18 ksi and ra=11 ksi. The most economical beam is that having the largest capacity-to-weight ratio. Neglect fabrication costs in answering parts (c) and (d) above. Note: Obtain the dimensions and properties of all rolled shapes from tables in Appendix F.
A frame ABCD is constructed of steel wide-flange members (W8 x 21; E = 30 x ID6 psi) and subjected to triangularly distributed loads of maximum intensity q0acting along the vertical members (see figure). The distance between supports is L = 20 ft and the height of the frame is h = 4 ft. The members are rigidly connected at B and C. Calculate the intensity of load q0 required to produce a maximum bending moment of 80 kip-in. in the horizontal member BC. If the load q0 is reduced to one-half of the value calculated in part (a), what is the maximum bending moment in member BC? What is the ratio of this moment to the moment of 80 kip-in. in part (a)?
A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h = 120 mm and h1= 100 mm. The maximum allowable bending stress in the plastic beam is emix = 6 M Pa, and the bending moment is M = 150 N · m. Determine the minimum permissible width bminof the beam.
Draw the shear and Bending moment diagram of each beam below using the equation method and area method. CHANGE 20 kN/m to 33 kN/m
Draw the shear and moment diagram of the beam shown. Please show the complete detailed solution.
Draw the shear-force and the bending-moment diagrams and specify the maximum values and their locations on the beam. only Handwitten answer needed please. do not type
The beam weight is 5kN considered as a distributed load over the beam length. Two bushwalkers with 850N weight each are standing together at one end of the beam/bridge. Determine the maximum shear force and bending moment in the simply supported beam shown below.
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 5.0 ft, b = 3.4 ft, P = 25 kips, and w = 1.1 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Draw the shear and moment diagram of the overhanging beam shown below. For this part, please show the necessary solutions using the LONG METHOD, not the AREA MOMENT METHOD
Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the maximum shear and maximum bending moment that occur in the span by method of section and method of area. Provide a detailed and complete solution
A thin-walled closed section beam of constant wall thickness t has the cross-section shown inFigure. Length of 1-2 and 3-4 is a and length of curve 2-3 and 4-1 is b. Draw the shear flowdistribution diagram.
A simply supported beam of length 5m, carries a uniformly distributed load of 12019080kN/m extending from the left end to a point 2m away. There is also a clockwise couple of 12020280 kNm applied at the centre of the beam. Draw the S.F and B.M diagrams for the beam and find the maximum bending moment.