A vertical piston cylinder assembly containing water is being heated on a stove. During this process, 100 BTU of heat is transferred to the water. In the water's expansion process (because of the heat addition) 8000 ft- Ibf of work is done. Also, there is 20 BTU heat loss from the assembly. What is the water's change of energy as a result of the heat addition process? u of 2628 kJ/kka ot 70

A vertical piston cylinder assembly containing water is being heated on a stove. During this process, 100 BTU of heat is transferred to the water. In the water's expansion process (because of the heat addition) 8000 ft- Ibf of work is done. Also, there is 20 BTU heat loss from the assembly. What is the water's change of energy as a result of the heat addition process? u of 2628 kJ/kka ot 70

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 27RQ: How many Btu/h would be produced in a 12-kW electricheater?

See similar textbooks

Similar questions

A steam power station uses coals of calorific value of 6045-kcal/kg. The overall efficiency ofthe power station is 21.5% and a coal power station uses 4.05-tonnes of coal every 15 minutesto generate the maximum demand. The purchasing price of coals is R600 per tonne. (NB:1 kWh = 861 kcal)(a) Determine the coal consumption in kg per kWh.(b) Determine the cost of purchasing the coals per week if the load factor is 65%.
A heating system that uses heated water has a total heating load of 587 thousand btuh. How much heated water flow in gallons per minute (GPM) is required to satisfy the total load if the system is designed for 34 °F temperature change?
On average, 0.59 kg of CO2 is produced for each kWh of electricity generated from a power plant that burns natural gas. A typical new household refrigerator uses about 700 kWh of electricity per year. Determine the amount of CO2 production that is due to the refrigerators in a city with 300,000 households.
The interior of a refrigerator has a surface area of 6.2 m2 . It is insulated by a 2 cm thick material that has a thermal conductivity of 0.0199 J/m · s · ◦ C. The ratio of the heat extracted from the interior to the work done by the motor is 5.5 % of the theoretical maximum. The temperature of the room is 27.6 ◦C, and the temperature inside the refrigerator is 6.6 ◦C. Determine the power required to run the compressor. Answer in units of W.
3: Determine the second law efficiency of the heat engine operating between “550” ºC and “30” ºC. The heat engine has efficiency of “35” %
1) Given 753.06 kW electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 1.5(10^5) W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Answer the following: a) Calculate the exergy destroyed in the process below. The exergy of the fuel entering this process is 51.82 MJ/Kg. The dead state temperature is 293.2 K and pressure is 1 bar. The products of combustion leave this process at the dead state. Process: 0.015 kg is the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to the conditions of the problem above. if the electrical heating device is replaced with a gas fired boiler. The high heating value (HHV) of the fuel is 50.02 MJ/kg. b) The utility providing the…
A 10 kW drilling machine is used to drill a bore in a small aluminum block of mass 8 kg. How much is the rise in temperature of the block in 2.5 minutes, assuming 50% of power is used up in heating the block? (specific heat of aluminum : 0.91 J/(g °C))
during the working stroke of an engine the heat transferred out of the system was 160kJ/kg of working substance. the internal energy also decreased by 405kJ/kg of working substance. Determine the work done
The refrigerant circulating in the following system is R404A; the data of the system is as follows: Tev1= -20 oC Tev2= 0 oC, Qev1=10 kW, Qev2=20 kW, Tkon= 40 oC, the efficiency for the compressor is nik=0.80, nmk=0.90, nkk=0.95, nem=0.95. 10 oC over-cooling and 10 oC over-heating will be done in the system. a) draw p-h and T-s diagrams of the cycle.b) 1. and 2. calculate the mass flow through the evaporator and through the compressor.c) determine the temperature (T2) and enthalpy (h2) at the compressor output.d) 1. and 2. determine the degree of dryness when entering the evaporator.e) What would have happened if the expansion valve between stations 5 and 6 had not been used?f) find the power consumed by the compressor.g) determine the cooling performance coefficient COPSM value.H) calculate condenser capacity.I) calculate the heating performance coefficient (COPIP) of the system.
If the LHV of wood logs is 16 MJ/kg, how much energy is available for 2 kg of wood logs? If I burn all wood logs, what is the maximum energy in the heat I could obtain? If 30% of heat can be changed to electricity, how much electricity will be generated? If the heating value (LHV) of dry wood is 20 MJ/kg, what is the maximum energy 20 tonnes of wood could provide? If 60 % of the heat in wood could be transferred, how much heat can be transferred? If the heating value of coal is 40 MJ/kg, how much energy is available for 10 tonnes of coal? If I burn wood logs (LHV =16 MJ) to obtain the same amount of heat, how much (in tonne) of wood logs do I need to burn?
A heat pump with a coefficient of performance of 1.8 supplies energy toa house at a rate of 75 MJ h-1. Determine the electrical power used bythe heat pump. answer: 12kJ Please show all working out
An electric windshield defroster is used to remove 0.25-in of ice from a windshield. The properties of the ice are Tsat = 328F, uif = hif = 144 Btu/lbm, and v = 0.01602 ft3/lbm. Determine the electrical energy required per square foot of windshield surface area to melt this ice and remove it as liquid water at 328F. What is the minimum temperature at which the defroster may be operated? Assume that no heat is transferred from the defroster or ice to the surroundings.