A wall has inner and outer surface temperatures of 16 and 6°C, respectively. The interior and exterior air tem- peratures are 20 and 5°C, respectively. The inner and outer convection heat transfer coefficients are 5 and 20 W/m² K, respectively. Calculate the heat flux from the interior air to the wall, from the wall to the exterior air, and from the wall to the interior air. Is the wall under steady-state conditions?

A wall has inner and outer surface temperatures of 16 and 6°C, respectively. The interior and exterior air tem- peratures are 20 and 5°C, respectively. The inner and outer convection heat transfer coefficients are 5 and 20 W/m² K, respectively. Calculate the heat flux from the interior air to the wall, from the wall to the exterior air, and from the wall to the interior air. Is the wall under steady-state conditions?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.15P: 2.15 Suppose that a pipe carrying a hot fluid with an external temperature of and outer radius is...

See similar textbooks

Similar questions

A plane wall 15 cm thick has a thermal conductivity given by the relation k=2.0+0.0005T[W/mK] where T is in kelvin. If one surface of this wall is maintained at 150C and the other at 50C, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.
Discuss the modes of heat transfer that determine the equilibrium temperature of the space shuttle Endeavour when it is in orbit. What happens when it reenters the earths atmosphere?
A plane wall of thickness 2L has internal heat sources whose strength varies according to qG=qocos(ax) Where qo is the heat generated per unit volume at the center of the wall (x=0) and a is a constant. If both sides of the wall are maintained at a constant temperature of Tw, derive an expression for the total heat loss from the wall per unit surface area.
2.15 Suppose that a pipe carrying a hot fluid with an external temperature of and outer radius is to be insulated with an insulation material of thermal conductivity k and outer radius . Show that if the convection heat transfer coefficient on the outside of the insulation is and the environmental temperature is , the addition of insulation actually increases the rate of heat loss if , and the maximum heat loss occurs when . This radius, is often called the critical radius.
A steam pipe 200 mm in diameter passes through a large basement room. The temperature of the pipe wall is 500C, while that of the ambient air in the room is 20C. Determine the heat transfer rate by convection and radiation per unit length of steam pipe if the emissivity of the pipe surface is 0.8 and the natural convection heat transfer coefficient has been determined to be 10 W/m2K.
An electric heater producing 260 W of heat is used to warm up a room containing 7 m3 of air. If we assume the room is perfectly sealed and there is no heat loss through the room boundaries, such that all of the heater output goes into increasing the air temperature, how long will it take to heat up the air in the room from 5.0 °C to 24.1 °C? Give your answer to the nearest minute and assume that the specific volume (v = 0.85 m3/kg) and specific heat capacity at constant volume (cv = 1.005 kJ/(kg K)) remain constant throughout the heating process.
Find the amount of heat lost per hour through a square foot ofbuilding wall composed of 18-in. sandstone and 3/4-in. metal lath andplaster separated by a 1 1/4-in. air space, when the temperature of theroom is 70 °F, the outdoors is 10 °F, and the wind velocity is 15 mph.
1 - A square chip, with side w = 5 mm, operates under isothermal conditions.The chip is positioned on a substrate so that its side and bottom surfaces are thermally insulated, while its top surface is exposed to theflow of a refrigerant at T∞ = 15°C. From reliability considerations, the chip temperature cannot exceed T = 85°C. The refrigerant being air, with a convection heat transfer coefficientcorresponding h = 200 W/(m2K), what is the maximum allowable power for the chip? Since the coolant is a dielectric liquid for which h = 3000 W/(m²K), what is the maximum allowed power?
HEAT TRANSFER (a) Determine the thermal conductivity of an insulating material given the following data: steel pipe with 0.1025 m inner diameter and 0.1150 m outer diameter, insulation thickness 3 cm, heat flow per meter is 150 W/m, steel thermal conductivity 55 W/m-°C, and overall temperature difference of 72.2°C. If the temperature of the steam inside the pipe is 128°C, (b) find the outside temperature of the insulating material.
Model the following heat transfer situations. Specify heat flows and storages. Try to write down the mathematical expressions. (i) Solar heating of the road surface (ii) A steam pipe passing through an open space between two buildings (iii) Heat transfer from a person in a warm room in the cold season (iv) Pressure cooker-warming up-cooling down (v) Pressure cooker-steady conditions (vi) A rod with one end in a furnace and the remaining surface in atmosphere (vii) A wire carrying current, exposed to air (viii) A water heater (electrical) with hot water being drawn out with cold water admission. (ix) Cake being baked in an oven or a fruit placed in a refrigeration (x) A frying pan placed on a stove. 1.2 Choose the correct statement in each question. (i) A pipe carrying steam at about 300°C traverses a room, the air being still at 30°C. The major fraction of the heat loss will be by (a) conduction to the still air (b) convection to the air (c) radiation to the surroundings…
A solar energy storage compartment contains 1,778 rocks that can approximate 3-inch-diameter spheres. The properties of the rocks are k = 2.2 Btu / h ∙ ft ∙ ºF, α = 0.07 ft2 / h, cp = 0.2 Btu / lbm ° F, and the density is 160 lbm / ft3. How long (in hours) would it take for solar energy to saturate the compartment using 200 ° F air from a solar collector? How much energy (in Btu) is stored in the compartment under these conditions if it is initially at 79 ° F and h = 5 Btu / h ∙ ft2 ∙ ºF?
5. An irregularly shaped solid made of a material with a density of 3200 kg/m³ has a volume of 0.003 m3 and a surface area of 0.07 m². The thermal conductivity of the material is 300 W/m K, and its specific heat is 500 J/kg K. Initially, there is a 100°C difference between the solid and its environment, what is the approximate time it will take for this system to have the difference between its temperature and the environment to be one-third of the initial difference? Use h- 60 W/m-K for the environment. Express your answer in minutes.