Answered: A water pipe is connected to a double-U…

Name: o snapshot.pngA water pipe is connected to a double-U manometer as sh
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: o snapshot.pngA water pipe is connected to a double-U manometer as shown in Figurebelow at a location where the local atmospheric pressure is 97.9 KPa.Determine the absolute pressure at the center of the pipe.Oil SG= 0.80Oil SG= 0.8020 cmWaterpipe30

Engineering

Mechanical Engineering

A water pipe is connected to a double-U manometer as shown in Figure below at a location where the local atmospheric pressure is 97.9 KPa. Determine the absolute pressure at the center of the pipe.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

A water pipe is connected to a double-U manometer as shown in Figure below at a location where the local atmospheric pressure is 97.9 KPa. Determine the absolute pressure at the center of the pipe.
A water pipe is connected to a double-U manometer as shown in figure below at a location where the local atmospheric pressure is 12.6 psia. Determine the absolute pressure at the center of the pipe.
A water pipe is connected to a double-U manometer at a location where the local atmospheric pressure is 14.5 psia. Determine the absolute pressure at the center of the pipe.
A cylindrical tank of 1.5 m diameter and height 0,75 m has a hemispherical dome. The tank contains oil of relative density 0.84. The dame is joined to cylinder position by four equally spaced bolts. If pressure gauge at point M, 0.3 m above base of tank read 50 kPa. Determine force each bolt.
A gasoline line is connected to the pressure gage through a double-U manometer, as shown in the figure. If the reading of the pressure gage is 370 kPa, determine the gage pressure of the gasoline line.6)
Pressure in a water container can be measured by an open vertical tube. If the expected water rise is about 20cm. What tube diameter is needed to ensure the capillary action is less than 3%?
The pressure at a point “m” in the figure shown was increased from 70 kPa to 105 kPa. This causedthe top level of mercury to move 20 cm in the sloping tube. What is the inclination, θ?
Two small vessels are connected to a U-tube manometercontaining mercury(relative density 13.56) and the connectingtubes are filled with alcohol (relative density 0.82). Thevessel at the higher pressure is 2 m lower in elevation than theother. What is the pressure difference between the vessels whenthe steady difference in level of themercury menisci is 225 mm?What is the difference of piezometric head? If an inverted U-tubemanometer containing a liquid of relative density 0.74 wereused instead, whatwould be the manometer reading for thesame pressure difference?
A U-tube manometer is connected to a closed tank as shown. The air pressure in the tank is 0.25 psi and the liquid in the tank is oil (SG=0.6) . The pressure at point A is 1 psi. a. Determine the depth z (in feet) of oil in the tank. b. Determine the differential reading, h (in feet), on the manometer.
Three types of fluids stack in an open tank as shown in the picture. If the specific gravidties are sg1=1, sg2=1, sg3=1, and h1=0 m, h2=0 m, h3=0 m, calculate the gage pressure at location 4, P4(gage)=_________(kPa)
Pipe A contains gasoline (SG = 0.7), pipe B contains oil (SG = 0.9), and the manometer fluid is ,ercury. Determine the new differential reading if the pressure in pipe A is decreased 25 kPa, and the pressure in pipe B remains constant. The initial differential reading is 0.30 m. (Hydrostatic)
A Horizontal Capillary Tube (Radius 10 Um) Con- Tains An Oil/Water Interface. The Pressure In The Oil Phase Is 14.5 Psi (100 KPa). Determine The Pressure In The Water Phase If The Contact Angle Is 30° And The IFT Is 30 Dynes/Cm (30 MN/M).