A well was constructed to pump water from a confined aquifer. Two observation wells were constructed at distances of 350 m and 800m respectively. At a steady pumping rate of 0.39 m^3/min, the drawdown in the observation wells were respectively equal to 1.6 m and 7.8 m. Diameter of the test well is 0.95 m and thickness of confined aquifer is 16 m. a. Determine the hydraulic conductivity of the soil in m/min. (IN EXPONENTIAL FORM AND IN 2 DECIMAL PLACES) b. Determine the drawdown at the test well in m. (IN 2 DECIMAL PLACES) c. What is the value of the transmissivity of the confined aquifer in m^2/day? (IN 2 DECIMAL PLACES)

A well was constructed to pump water from a confined aquifer. Two observation wells were constructed at distances of 350 m and 800m respectively. At a steady pumping rate of 0.39 m^3/min, the drawdown in the observation wells were respectively equal to 1.6 m and 7.8 m. Diameter of the test well is 0.95 m and thickness of confined aquifer is 16 m. a. Determine the hydraulic conductivity of the soil in m/min. (IN EXPONENTIAL FORM AND IN 2 DECIMAL PLACES) b. Determine the drawdown at the test well in m. (IN 2 DECIMAL PLACES) c. What is the value of the transmissivity of the confined aquifer in m^2/day? (IN 2 DECIMAL PLACES)

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter7: Permeability

Section: Chapter Questions

Problem 7.3P

See similar textbooks

Similar questions

A pumping test was carried out in confined aquifer thickness 2 m and the following measurement was recorded. Rate of pumping was 10 m^3/s; drawdown in pumping well was 2.0 m while on the observation well located at 15 m and 20 m from the centre of the pumping well were 1.6 m and 1.4 m, respectively. Determine the hydraulic conductivity of soil.
1. Calculate the equivalent hydraulic conductivity for the soil profile shown in figure 2. An excavation is proposed for a square area near the bend of a river, as shown in figure. It is expected that the flow of water into the excavation will come through the silt layer. Pumping test reveal an average horizontal hydraulic conductivity of 2 x 10 -5 cm/s in the silt layer. The excavation has to be kept dry. Determine the flow (qs) into the excavation.
A pump well is dug through a confined aquifer having a thickness of 32 meters. The piezometric surface of the aquifer is 18 meters measured from the top impermeable layer. The first observation well is 75 feet directly west of the pump well and the second observation well is 75 feet directly north of the first observation well. Determine the hydraulic conductivity of the aquifer if it supplies a discharge of 10 liters per second and the drawdown of the observation wells are 13 feet and 23 feet.
Given: velocity of flow = 0.0375 m/s coefficient =0.05 m/s porosity p =48% slope S = 3/4 The soil porosity in the area where the 46-cm diameter well is 48%, find the discharge of the groundwater. Given the coefficient =0.05 m/s and porosity p =48%, find the transmissibility (T) in m/s per unit m, if the aquifer width is 1.2 m. Given the discharge Q get in Question #1, transmissibility T in Question#2, slope S = 3/4; find the aquifer width X.
Q:5 a)Find out the flow rate from a soil when hydraulic conductivity is 2.5x10^-3 cm/sec while the length of soil sample is 11 cm, dia of soil sample is 5 cm, change in head observed is 3 cm.
In a field testing, the hydraulic gradient between two peizometers is 1.11, the area of flow is 4.08 m2 and the hydraulic conductivity of the aquifer material is 0.94 m/day, calculate the discharge in m3/day. Note that discharge cannot be negative
Illustrated laboratory setup includes a column of homogenous soil with a square cross-section area of 25 cm2. A constant head difference is applied for the setup. Assume continuous, steady-state flow in a fully saturated medium, and all head loss occurs in the soil. Points A, B, and C are located as shown in the figure. The saturated unit weight of sand is 18 kN/m3. a) Determine the elevation, pressure and total head at Points A and B.b) Determine the hydraulic gradient.c) Determine the total amount of flow per minute if k = 10 cm/mind) Show the direction and calculate the seepage force acting on plane x-x.e) Calculate the effective stress along the plane parallel to the direction of flow assuming that the total stress along that direction is 25 kPa at Point C.
The static level of water table in an unconfined aquifer was 30 m above the underlying impermeablestratum. A 150 mm diameter well, penetrating the aquifer to its full depth, was pumped at the rate of20 liters per second. After several weeks of pumping, the drawdown in observation wells 20 m and 50m from the well were 3.5 m and 2 m respectively, and the observed drawdowns were increasing veryslowly (B.Sc., DU, 2012).a) Assuming equilibrium conditions, estimate the hydraulic conductivity and transmissivity of theaquifer.b) Estimate the drawdown just outside the pumped well.c) What will be the yield of a 300 mm diameter well which will produce the same drawdowns justoutside the well and at the 50 m distance observation well in (2)? What would be the drawdown at anearer observation well?
b) A 30-cm well fully penetrates an unconfined aquifer of saturated depth 25 m. When a discharge of 2100 lpm was being pumped for a long time, observation wells at radial distances of 30 m and 90 m indicated drawdown of 5 and 4 m respectively. Estimate the coefficient of permeability and transmissibility of the aquifer. What is the drawdown at the pumping well?
A well penetrates an unconfined aquifer. Prior to pumping the water level(head) is ho = 25m after a long period of pumping at a constant rate of 0.05 m^3/s the drawdowns at distances of 50m and 150 m from the well were observed to be 3 m and 1.2 m respectively. Compute the hydraulic conductivity of the aquifer and the radius of influence of the pumping well. What type of deposit is the aquifer material?
A 30 cm well penetrates an unconfined aquifer of saturated depth of 25m. When a discharge of 2100 lpm was being pumped for a long time, observation wells at radial distances of 30m and 90m indicated drawdown of 5m and 4m, respectively. Estimate the coefficient of permeability and the drawdown at pumping well.
Two observation wells have been constructed in the formation shown. The flow rate is 0.01 m3/hr per unit width of the formation. 1. Compute the hydraulic gradient. 2. Compute the equivalent hydraulic conductivity. 3. Compute the value of K2.