(a) What is the total impedance of an inductor with a reactance 150 Q when connected to the following? 1. In series with a resistance of 100n 2. In parallel with a resistance of 200 Q. 3. Do the values of the impedances change when the inductor is replaced by a capacitor having the same reactance value?

(a) What is the total impedance of an inductor with a reactance 150 Q when connected to the following? 1. In series with a resistance of 100n 2. In parallel with a resistance of 200 Q. 3. Do the values of the impedances change when the inductor is replaced by a capacitor having the same reactance value?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PA: You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor...

See similar textbooks

Similar questions

You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor to a 480-V, 60-Hz line. To determine the proper conductor and fuse size for this installation, you need to know the amount of current the inductor will draw from the line. The nameplate on the inductor indicates that it has an inductance of 0.1 H. An ohmmeter reveals that it has a wire resistance of 10 . How much current should this inductor draw when connected to the line?
Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A. If one says that an inductor absorbs zero real power and positive reactive power. is it (a) True (b) False B. If one says that a capacitor absorbs zero real power and negative reactive power (or delivers positive reactive power), is it (a) False (b) True C. If one says that a (positive-valued) resistor absorbs (positive) real power and zero reactive power, is it (a) True (b) False
A circuit element has the following voltage across it and current running through it.?(?) = 3 cos(100? + 30°) V,?(?) = 50sin(100? + 30°) mA.Assume polarities are chosen so that the current is flowing into the positive voltage terminal.(a) Determine if this circuit element is a resistor, capacitor, or inductor.(b) Find the impedance of this circuit element.(c) Find the component value of the circuit element. ie. if it is an resistor find R, if it is a capacitor, find C, if it is an inductor, find L.
A battery of emf 30.0 V is connected to a switch, an inductor of inductance ? = 0.600 ? and two resistors, R1 = 10.0 ? and R2 = 6.00?. The switch is initially open. A. What are the values of currents ?1, ?2, ?3 just after the switch is closed? (Just give an answer) ?1 = ?2 = ?3 = B.)Which point, a or b, is at higher potential or are they at the same potential, just after switch S is closed? (Just give an answer) C. What is the value of current ?1 through the battery a long time after the switch is closed? Show your work and briefly explain your logic
Vbatt=25 VC1=90 ?CC2=75 ?CC3=60 ?CR1=160 ΩR2=120 Ωt2=21.6 msect3=27 msecConsider the circuit shown below which shows a battery connected to some resistors and capacitors along with some switches which will be toggled opened or closed at different times. The components are listed above. The capacitances are in microCoulombs (?C), the resitances are in Ohms (Ω), and the times are in milliseconds (msec). A stopwatch is started at time t1=0 ms. At that time, switch S1 is closed and all other switches are open and the capacitor is allowed to charge up.(a). What is the charge (in uC) on C1 at the time the stopwatch reads t2=21.6 ms?Ans: 1750 uC(b). What is the current (in mA) through R1 at t2=21.6 ms?Ans: 34.9 mA(c). What is the voltage (in V) across R1 at t2=21.6 ms?Ans: 5.58 V(d). What is the voltage (in V) across C1 at t2=21.6 ms?Ans: 19.4 V(e). What is the energy (in mJ) in C1 at t2=21.6 ms?Ans: 17.0 mJThen, immediately at time t2=21.6 on the stopwatch, switch S1 is thrown open and…
Vbatt=25 VC1=90 ?CC2=75 ?CC3=60 ?CR1=160 ΩR2=120 Ωt2=21.6 msect3=27 msecConsider the circuit shown below which shows a battery connected to some resistors and capacitors along with some switches which will be toggled opened or closed at different times. The components are listed above. The capacitances are in microFarads (?F), the resitances are in Ohms (Ω), and the times are in milliseconds (msec). A stopwatch is started at time t1=0 ms. At that time, switch S1 is closed and all other switches are open and the capacitor is allowed to charge up.(a). (i)What is the charge (in uC) on C1 at the time the stopwatch reads t2=21.6 ms?a)3690 b)1520 c)5710 d)2630 e)683 f)1750 (a).(ii)What is the current (in mA) through R1 at t2=21.6 ms?34.9 30.4 114 13.6 73.6 52.4 (b)(i)What is the voltage (in V) across R1 at t2=21.6 ms?8.37 5.58 2.18 11.8 18.2 4.85(ii). What is the voltage (in V) across C1 at t2=21.6 ms?63.2 29.1 40.9 7.57 19.4 16.9(c). (i) What is the energy (in mJ) in C1 at t2=21.6 ms?6.63…
The following data was collected in a lab where a 1000 uF capacitor was discharged using a 3 volt power supply. The capacitor was in series with a resistor of unknown value. a. Draw an RC circuit diagram where a capacitor can be charged and discharged in the same circuit using asingle pole double throw switch.b. Construct a graph of showing the discharge curve of the capacitor’s voltage with time using the databelow.c. Linearize the data below to construct a straight line with a constant slope.d. The graphs should be labeled and titled. The axes should be labeled with appropriate units.e. Using the the linearized data calculate the time constant for the RC circuit.f. Calculate the value of the unknown resistor.g. Show that the capacitor is nearly discharged after 5 time constants.
A coil of inductance 5 H and a resistance of 16 Ω is connected to a 120 V DC supply. Determine (a) the steady state value of current flowing in the coil, (b) the time constant of the circuit,(c) the value of the induced e.m.f. after 0.2 s, (d) the time for the current to rise to 85% of its final value, and (e) the value of the current after 0.5 s.
A 500 ohm resistor, an 1.5 F uncharged capacitor, and a 6.16-V emf are connected in series. (a) What is the initial current? (b) What is the time constant? (c) What is the final voltage on the capacitor? (d) what is the final charge on the capacitor? What is the final energy stored in the capacitor? (e) Express (i) Current in the circuit, (ii) Voltage on the capacitor, (iii) Charge accumulated on either plate of capacitor, (iv) energy stored in the capacitor as a function of time. (must include all the value calculated in the earlier part). (f) What is the i) current ii) charge on capacitor, iii) voltage on capacitor & iv) Energy stored in the capacitor after one time constant?
a) You are provided with three capacitors of values 4µF, 6µF, 30µF and 220V power supply. Connect the 4µF and 6µF in parallel; and then connect the combination to the 30µF in series. Connect the 220V power supply across this arrangement and find (i) the equivalent capacitance of the circuit formed, (ii) the voltage across 30µF, (iii) the charge on each capacitor. (iv) If the circuit formed is switched ON for 3minutes, what will be the amount of current flowing through the circuit? (b) What is the accuracy of a measurement of 26.5gm taken as against 25gm? (c) State the types of resistor colour band in use and hence determine the colours of the following resistors: (i) K39±10%; (ii) M56±1%; (iii) 3K9±10%; (iv)120K±2% (v) 8R8±10%
By means of a battery, a capacitor C1 of 3.55 μf is charged until it reaches a potential difference △V0 = 6.3 volts. Then the battery is removed and as shown in the figure below, the capacitor is connected to another discharged capacitor C2 of 5 μf until equilibrium is achieved, with both capacitors at the same charge. a) What is the potential difference in each? b) What is the energy stored in the electric field before and after closing the switch?
capacitor having capacitance of 10uF is connected with 1k ohm resistor in series. The switch of the DC supply of 10 Volts, closes at t = 0. Compute the following a. Draw a circuit diagram for t- and t+ b. Compute the time constant c. Plot the Voltage with respect to time, showing the behavior of capacitor charging(take at least 10 values of time in seconds to draw a graph).