A wheel that is initially at rest has forces applied to it, as shown in (Figure 1), and it begins to rotationally accelerate. Part A Calculate the net torque about the axle of the wheel shown in (Figure 1). Assume that a friction torque of 0.75 m N opposes the motion. Express your answer using two significant figures. m-N Submit Request Answer Provide Feedback Figure < 1 of 1 > 35 N. 28 N 135 12 cm 24 cm 18 N

A wheel that is initially at rest has forces applied to it, as shown in (Figure 1), and it begins to rotationally accelerate. Part A Calculate the net torque about the axle of the wheel shown in (Figure 1). Assume that a friction torque of 0.75 m N opposes the motion. Express your answer using two significant figures. m-N Submit Request Answer Provide Feedback Figure < 1 of 1 > 35 N. 28 N 135 12 cm 24 cm 18 N

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter9: Momentum And Its Conservation

Section9.1: Impulse And Momentum

Problem 7PP

See similar textbooks

Similar questions

Suppose you start an antique car by exerting a force of 275 N on its crank for 0.245 s. What angular momentum is given to the engine, in kg · m2/s, if the handle of the crank is 0.300 m from the pivot and the force is exerted to create maximum torque the entire time?
As you switch a fan setting from its slowest speed to its highest,its angular speed v triples. (a) Does the period of rotation T of thefan blade increase, decrease, or stay the same? Explain. (b) Whatis the ratio of the new rotation period to the old value, Tnew>Told?
For each of the four forces F 1, F2, Fgrav, and Faxle, is the torque about the axle positive (+), negative (-), or zero (0)?
(Figure 1) shows a uniform 2.0 kg rod that can pivot in a vertical plane on an axle. We want to find the net torque about the axle. For each of the four forces F 1→1, F 2→2, Fgrav→ and F axle→, is the torque about the axle positive (+), negative (-), or zero (0)?
A diver (such as the one shown in the figure(Figure 1) ) can reduce her moment of inertia by a factor of about 3.5 when changing from the straight position to the tuck position. If she makes 2.0 rotations in 1.2 s when in the tuck position, what is her angular speed (rev/srev/s) when in the straight position?
A windmill has an initial angular momentum of 8500 kg # m2>s.The wind picks up, and 5.86 s later the windmill’s angularmomentum is 9700 kg # m2>s. What was the torque acting on thewindmill, assuming it was constant during this time?
A roller has a mass of 1,081.8kg, a radius of gyration of 107.3 mm, and is lifted by 2 ropes as shown . If each cable has the following tensions TA =3,195.7 N and TB =3,308.5 N, determine (a) the angular acceleration of the roll? Input your answer with 2 decimal places and make sure it is positive.
A wheel with a rotational inertia of 4.5 kg•m accelerates at a rate of 3.0 rad/s?. What net torque is needed to produce this acceleration? Use the right formula to solve and get the correct answer.
Find the magnitude of the net torque on the wheel in Figure below about the axle through O, taking a=10cm, b=34cm. The magnitude of the applied forces are F1=16N, F2=16N, and F3=22N. Provide your answer in units of m⋅N and round off your answer to 2 decimal places.
(Figure 1) illustrates an Atwood's machine. Let the masses of blocks A and Bbe 8.50 kg and 1.00 kg , respectively, the moment of inertia of the wheel about its axis be 0.220 kg⋅m2, and the radius of the wheel be 0.120 m. There is no slipping between the cord and the surface of the wheel. Find the magnitude of the linear acceleration of block A. Find the magnitude of linear acceleration of block B. Find the magnitude of angular acceleration of the wheel C. Find the tension in left side of the cord. Find the tension in right side of the cord.
A vertical solid disk of uniform mass ?=7kgM=7kg and radius ?=0.5mR=0.5m is pivoted from point ?O as shown in the figure below. A constant radial force of ?=117NF=117N is applied where the angle ?=36?β=36o. If ?=0.36mx=0.36m, determine the angular acceleration of the disk in SI units at the instant shown. Express your answer using two decimal places. Please use the convention: Clockwise (-), Counterclockwise (+) when expressing your answer. Hint 1: The moment of inertia of a uniform disk about an axis of rotation passing through the center of mass (CM) is ???=??2/2ICM=MR2/2. Hint 2: Don't forget the force of gravity!!! Take ?=9.80m/s2g=9.80m/s2.
The body in the figure is pivoted at O. Three forces act on it in the directions shown: FA = 8.10 N at point A, 5.60 m from O; FB = 16.0 N at point B, 3.90 m from O; and FC = 18.0 N at point C, 3.50 m from O. Taking the clockwise direction to be negative, what is the net torque about O? 8.78 is incorrect.