Please asap points are not vectors. Vectors are commonlyconstructed from either: (1) the ongin to a point or (2) astarting point to an ending point.Figure1 of 3A wire is connected to two supports. (Eigure 3) The support on the wall has coordinates A3.55 ft and 43 55 ft. The support on the ground has coordinates ag=1.18 ft and yo4.30 ft What are the i. j. and k components of the unit vector u that describes the line ofaction from point A to point B?Express your answers to three significant figures separated by commas.▸ View Available Hint(s)My My MySubmitIVE ΑΣΦvec→

The support on wall A from the origin,xA = 3.55 ft, zA = 3.55ftThe position…

A wire is connected to two supports (Figure 3) The support on the wall has coordinates A 3.55 ft and A-355 ft. The support on the ground has coordinates zg-1.18 ft and ga 4.30 ft What are the i. j. and k components of the unit vector u that describes the line of action from point A to point B? Express your answers to three significant figures separated by commas. View Available Hint(s) My My My Submit 195] ΑΣΦ 11 vec -8?

A wire is connected to two supports (Figure 3) The support on the wall has coordinates A 3.55 ft and A-355 ft. The support on the ground has coordinates zg-1.18 ft and ga 4.30 ft What are the i. j. and k components of the unit vector u that describes the line of action from point A to point B? Express your answers to three significant figures separated by commas. View Available Hint(s) My My My Submit 195] ΑΣΦ 11 vec -8?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.22P: A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo...

See similar textbooks

Similar questions

Two blocks are connected by an ideal string, which passes over a pulley without slipping (see figure). The magnitudes of the wire voltages applied to blocks 1 and 2 are represented, respectively, by T1 and T2. Consider T2>T1. In this case, the pulley rotates counterclockwise. The pulley has radius R=0.10 m and rotates around an axis perpendicular to its surface passing through its CM. The CM of the pulley coincides with its center. The pulley's moment of inertia about the axis of rotation is denoted by I and its angular acceleration is α=0.50 rad/s2. If T2=87 N and T1=50 N, determine I (in kg⋅m2). A) 0,67 B) 0,56 C) 15 D) 28 E) 24 F) 0,85 G) 14 H) 7,4
Evaluate the mobility and naure of the kinematic chain shown in the Figure shown below
Draw a free-body diagram of the ring at C. (Figure 1)Draw the vectors starting at the black dot. The location and orientation of the vectors will be graded. The length of the vectors will not be graded.
a = 4 mb = 3.2 mc = 2 mF = {-7i+4j+12k} NSpecified axis: AF Find the following: Find the z-component of the moment of F about the specified axis. Find the x-component of the moment of F about the specified axis. Find the magnitude of the moment of F about the specified axis. Find the y-component of the moment of F about the specified axis.
I've recieved an answer to this question before, but I don't understand it. We're supposed to use vectors to find the answers. Thank you! This is all the information that's given: A link arm (see figure below) has the mass m and center of gravity / center of mass at point G. The arm is freely articulated at point O. At points A, B and C, respectively, there are attachments for a spring and a rope that runs over a stationary pulley at point D (neglect the dimensions of the pulley). The spring is 2.0 m long in the untensioned position and gives a force F = k s on the arm, where s is the extension / compression of the spring. If the arm is in equilibrium, the sum of all moments of force on the arm must be zero, ie. Sum(Mi) = Sum(ri) × Fi = 0 Data: m = 150 kg, k = 4.0 kNm^−1, OG = 1.4m, OB = 2.8m, OC = 4.2m, D = (7, 3) m, g = 9.8ms^−2 a) Identify all the forces that give a moment (with regards to 0) and express both the forces and position vectors for the forces' points of attack in…
A crank-rocker mechanism is to be used to drive a ratchet mechanism. Using mathematics and specific illustrations, find the required coupler length in inches required to generate this motion. The swing of the rocker is 35.0 from the vertical position in each direction. (Note: O2 is the crank pivot; O4 is the rocker pivot; C is the coupler-rocker joint; B is the coupler-crank joint). O2O4: 4.1 in.; lies in the horizontal plane O4C: 4.8 in.; mid stroke is vertical
For the scotch yoke mechanism shown in the figure P4.1, the horizontal position of link 4 canbe described as x = 3 cos (50t + 40°). Determine the displacement of link 4 during theinterval of 3.8 to 4.7 s.
3 points are plotted in the x, y, & z-plane as follows: A(-1,0,3); B(4, 2, 0); C(0,-1,-1). Establish a position vector from point B to point A. Please include a free-body diagram if possible. Choices are as follows: a) 0.81i + 0.32j - 0.49kb) 0.78i + 0.59j - 0.20kc) 0.24i - 0.24j - 0.94kd) 0.81i + 0.32j + 0.49ke) 0.81i - 0.32j + 0.49kf) 0.24i + 0.24j + 0.94kg) 0.78i - 0.59j - 0.20kh) 0.81i - 0.32j - 0.49ki) 0.78i + 0.59j + 0.20kj) 0.78i - 0.59j + 0.20kk) 0.24i - 0.24j + 0.94kl) 0.24i + 0.24j - 0.94k
1. A pulley 580 mm in diameter transmits 60 kW at 650 1pm by means of belt. Determine the effective belt pull.2. Find the angle of contact on the small pulley for a belt drive with center distance of 75 in. if pulley diameters are 9 in and 18 m, respectively.
Define the necessary equations to find the behavior of the mechanism (reduced at its maximum expression). All link lengths are known, as are the distances between supports. Consider that points B, C and E form an equilateral triangle. The entry angle (g) is specified to continuation.
A mechanism consists of two slender rods AP and OC is given in Figure 1. The AP rod is pinned to a moving ring, which can freely slide over OC rod. The dimensions of the system at the given instant (when θ = 60◦ and ϕ = 45◦ ) are lAP = 0.12 m, lOP = 0.25 m, and lOC = 0.35 m. The masses of the elements are mAP = 0.3 kg, mOC = 0.5 kg, and mring = 0.1 kg. At the given instant, the AP rod rotates with an angular velocity of ωAP = 2 rad/s, and angular acceleration of αAP = 7 rad/s2 (both in the counter-clockwise direction). Determine the angular velocity, and the angular acceleration of the OC rod at the given instant. Note: Neglect any friction.
3.1 [15] Compute the kinematics of the planar arm from Example 3.3.