1 kN/m M A 2m 4m 1 kN/m bob B 3m

Q: The bending moment M of a beam of length / at a distance x from one end is given by M = Wx(1-x)/2,…

A:

Q: A one mole of Methane is burned at equivalence ratio (0.7), the fuel air mixture at initial…

A: To determine the mole fraction of product analysis and the adiabatic flame temperature after…

Q: Calculate the power required for a water pump used in a closed system with flow rate Q = 0.0076m ^ 3…

A:

Q: In a meat processing plant, 4 cm-diameter spherical meat balls (k=0.45 W/m-K and α=0.91×10-7 m²/s)…

A:

Q: The two axes of an x-y positioning table are each driven by a stepping motor connected to a…

A: The gear reduction is:The number of step angles is:The pitch of the lead screw is:/revThe axis range…

Q: The figure shows a stepped steel shaft supported in bearings at A, C and loaded by a 2 kN force at…

A: please refer handwritten solution

Q: Solve by differential equation by undetermined coefficients A weight of 32Ib is subjected to a…

A:

Q: Two Points are connected by a A and B generalized coordinates AB TV Can move B rod of length L. The…

A: 1st assign cordinate point to A and B.then write pyhtagorus equation .

Q: A flat belt, of density 1000 kg/m3 has a maximum permissible stress of 2·5 MN/m². The belt is 200 mm…

A: The density of the belt material, ρ = 1000 kg/m³The maximum permissible stress, σ = 2/5 MN/m²The…

Q: Problem 4 A solid circular drive shaft connect a motor to gears B and C. The torque on gear B is 600…

A: Torque on gear B = 600 Nm Torque on gear C = 200 NmG = 66 GPa = 66 × 109 PaDiameter d=25 mmRadius r…

Q: Determine the magnitude of the vector sum V-V₁ + V₂ and the angle 0x which V makes with the positive…

A:

Q: A person is 1.65 m tall. a. Calculate the difference in blood pressure between the feet and top of…

A:

Q: Figure 3m 1 of 1 Part A Determine the maximum uniform loading w the W 310 x Jallow = 130 MPa and the…

A: Draw the free-body diagram of the beam.

Q: Q3: Consider the force F(t) acting on the spring-mass system shown in figure (1). Using Fourier…

A:

Q: Problem 4 The steel pipe AB has a 102-mam outer diameter and a 6-mm wall thickness. Knowing that arm…

A:

Q: Freight car A with a gross weight of 138000 lb is moving along the horizontal track in a switching…

A:

Q: Two cylinders are connected by a plank and rest over inclined planes as shown. An external load P is…

A: Two cylinders are connected by a plank and rest over inclined planes as shown. An external load P is…

Q: Other than Carbon and Hydrogen what other element is present in the singular repeating structure of…

A: There is PVC material which is poly vinyl chloride.Poly vinyl chloride consist of the group of…

Q: *13-8. Air has a temperature of 20°C and an absolute pressure of 600 kPa at .A. If the temperature…

A:

Q: energy balance

A: for writing energy balance for any combination process we need to some factors like-1- Energy…

Q: When the mechanism in the figure is in the position shown. the velocity of the center O of the disk…

A:

Q: YO FM B W₁ C Wo Fj FM Y U a B W₁ B Wo

A: a=13 cm, b=27 cm and c=36 cm, The angle that the long axis of the tibia makes with the horizontal…

Q: An L-shaped bracket is supported by a frictionless pin at A and a cable between points B and D. If…

A:

Q: or a turning operation, the cutting speed is 2.5 m/sec, and the depth of cut is 3 mm. A thrust force…

A: the cutting speed, v = 2.5 m/sthe depth of cut, d = 3 mm = 0.003 mThe thrust force, Ft = 300 Nthe…

Q: In an air standard Otto cycle the maximum and minimum temperatures are 1400 and 15°C. The heat…

A: Hi,As per the guidelines, we can solve only first question for you since you have not specified.…

Q: Topic: Shear and Bending Moment A gantry crane of weight W-100 Kg moves across a bridge with the…

A:

Q: A spheroldal Ecto-containment System (l.e. hollow vessel) has an Inner radius of 0.7 m. The…

A: Inner radius(r)=0.7mPressure (P)=230kPa = 0.230MPaNormal stress =29MPa

Q: Use R12 refrigerant Tconderser= 31oC Tevaporator=  -22oC Temp @ state 5 is = 1oC Qa= 20.01TR…

A:

Q: The horizontal uniform rod shown has length 0.60m and mass 2.0kg. The left end of the rod is…

A: Note: Center has

Q: Can you answer this?

A: Explanation:Acceleration is the rate of change of velocity concerning time. The slope of the v-t…

Q: The pump shown in the figure below produces a steady flow of 12 gal/s through the nozzle. Determine…

A: Given that,Steady flow rate through the nozzle = We know that, Hence, Nozzle exit velocity = To…

Q: E 160 GPa and I = 65.0(106) mm¹ (Figure 1) Figure 30 kN-m 3 m- 1 of 1 > Determine the slope of end A…

A: The young modulus of the beam, (E)=160 GPa.The moment of inertia of the beam, (I)=The moment at the…

Q: 4) An ideal gas undergoes a constant volume (isochoric) process in a closed system. The heat…

A: Two objective type question given related to…

Q: The 10-kg rod AB shown is confined so that its ends move in the horizontal and vertical slots. The…

A: Mass of the rod ABStiffness of the springRod is released from rest when the angle is 30 degree.And…

Q: Determine the reaction forces at points A, B & C. All supports have 2 forces. The first is…

A: The reaction forces at .FBD:The free-body diagram is shown below.

Q: Please determine the mass moment of inertia of the steel body that shown in the figure with respect…

A: Given:To find:Mass moment of inertia along Y axis

Q: FM A B W₁ Wo F₁ FM Y a A B W₁ Br 1 C Wo

A: a=12 cm, b=24 cm and c=36 cmThe angle that the long axis of the tibia makes with the horizontal is…

Q: Determine the magnitude of the vector difference V-V₂-V₁ and the angle 8x which V' makes with the…

A: According to the given dataa=3 and b=7V1=12 unitV2=16 unitThe angle are We need to findThe magnitude…

Q: The log is being towed by two tractors A and B. Determine the magnitudes of the two towing force FA…

A:

Q: A double-threaded worm with a lead angle of 20 degrees and axial pitch of 12.7 mm/tooth drives a…

A:

Q: A cylindrical billet of 60mm diameter is forged from 80mm height to 60mm at 1000 o C. The material…

A: The diameter of the cylindrical billet, d = 60 mmThe height of the cylindrical billet, H = 80 mmThe…

Q: 2. For a 6x4 ft two-dimensional body shown in the figure, determined the nodal temperatures. Take…

A: Data Given:

Q: A power transmission system consists of a motor connected to a pulley and a belt. The motor has a…

A: Given data of Power Transmission as below:Output Power P = 10 KW = 10*1000 = 10000 WSpeed N1 = 1200…

Q: 9. A lunar lander with a mass of 15,000 kg is descending onto the moon's surface with a velocity of…

A: Mass of the lunar lander, m=15000KgInitial velocity, V1=2m/sTime dependent thrust force, T=14t KN ,…

Q: The ultimate stress for a hollow steel column which carries an axial load of 1.9MN is 480N/mm if the…

A:

Q: 1.5 mm + 2.0 mm 2.0 mm 3.0 mm A shear force, S, is applied. This results in shear flow, shown with…

A: Shear flow at a junction is analogous to current at a junction. That is, the total amount of shear…

Q: Water 60°F flows at 10 ft/s in a 3 in. diameter pipe that is 100 ft long. There are six elbows (KL =…

A: Draw the schematic diagram of pipe system.Write the assumptions.(1) The flow is steady and…

Q: The steel tube has a thickness of 11 mm and the dimensions shown below. If the applied torque is…

A:

Q: An industrial plant has available a 4-cylinder, 76-mm bore by 102-mm stroke, 800 rpm, single-acting…

A: The refrigeration capacity.Given:The bore of the cylinder is .The stroke of the cylinder is .The…

Q: Thin wire bent into a three-sided "u" shape in the form of a block with pieces of equal length "b"…

A: