I. Draw the reactance diagram for the following power system in per unit using base power = 50 MVA and base voltage = 15 KV in the generator side. II. Calculate the fault current (If) in per unit and in ampere.

I. Draw the reactance diagram for the following power system in per unit using base power = 50 MVA and base voltage = 15 KV in the generator side. II. Calculate the fault current (If) in per unit and in ampere.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.30P: Determine the bus admittance matrix (Ybus) for the three-phase power system shown in Figure 6.23...

See similar textbooks

Related questions

Q: Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Line to ground fault has the highest probability in the power system O True False

A: Need to find true false

Q: 4 3. Show that when a single line-to-ground fault occurs in an ungrounded system, the neutral shift…

Q: Define and draw unit circle. What is the significance of unit circle for system analysis?

A: to draw and define unit circle significance of unit circle for system analysis

Q: Which among the following faults does mostly happen in 3-phase power systems? Single line to ground…

A: As 3 phase fault in power system are, 1. Single Line to Ground fault 2. Three phase short circuit 3.…

Q: Draw the negative- and zero-sequence impedance networks for the power system shown below. Mark the…

A: In this question we need to draw negative sequence and zero sequence per unit impedance diagram of…

Q: Line to line to line fault is an asymmetrical type of fault in power system which occurs very…

A: Given Line to line fault is an asymmetrical type of fault in power system.

Q: For the circuit shown, the normal operating values shown are known. If a symmetrical three-phase…

A: We can redraw the per-phase equivalent circuit as

Q: For the radial power system shown in Figure 3, calculate the line-to-ground fault current flowing in…

A: Apply KVL to find I1.Ps Z42 I1 + Z23 I1 + Z34 I1 – 1(angle 0) = 0 (Z42 + Z23 + Z34) I1 = 1(angle 0)…

Q: jX, (1) 2 3x. iX; E, O E. Figure 1

A: Three phase short circuit occur at bus 2 a) Calculating sub transient generator current Ig…

Q: Above is the one-line diagram of a simple power system. Each generator is represented by an emf…

A: The Given symmetric fault occurs 1 through a fault impedance Zi=j0.08 perunit. To determine the…

Q: A 3-phase, 3-wire system has a normal voltage of 10-4 kV between the lines. It is supplied by a…

A: We have 3-phase 3-wire system with, Line Voltage (V) = 10.4 KV Positive reactance (X1) = 0.6 Ω…

Q: For the system shown below, each generator has positive, negative, and zero sequence reactances of 3…

A: given for generator positive,negative and zero sequence impedance are =3 ,2 and 1 ohm for…

Q: 3) Draw the schematics of a HVDC and of a HVDC light, compare the systems evidencing advantages and…

A: HVDC means high voltage direct current is a method of electrical power transmission which uses…

Q: Explain how the value of fault current can be computed for L-L-G fault occurring at the terminals of…

A: Fault current: It is a current that comes into the picture when the fault occurs. The current is the…

Q: Problem 6 a- Explain the reasons for applying system grounding in electric power systems. Consider…

A: The current flowing through a circuit during a fault condition is called fault current. Fault types…

Q: For the system shown below, each generator has positive, negative, and zero sequence reactances of 3…

A: You have asked multiple independent questions. We are authorized to answer one question at a time.…

Q: Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and…

A: As per the guidelines of Bartleby we supposed to answer 1st three subparts of the question. For…

Q: 96\ Derive equations of critical clearing angle and time for a symmetrical three-phase fault at…

Q: Draw the reactance diagram of the given one-line diagram below marked in appropriate per unit…

A: There will be three sequence networks in the given power system- Positive-sequence network…

Q: The fault current level of a circuit breaker used in a transmission line with phase voltage 5.2 kV…

Q: in a tie-bus arrangement as shown in figure. the reactances of the generators and reactors are 0.2…

A: We redraw the circuit on per phase per unit basis: In the circuit the fault point is connected to…

Q: Q1/ for the four-bus power system shown in figure 1, the positive, negative and zero sequence…

Q: a. In sequence networks of power system, why does voltage sources appear only in the positive…

A: a) Machine are design such as it will generate voltage if the phase sequence will be same as…

Q: three phase generator with constant terminal voltages gives the following currents when under fault:…

A: The solution can be achieved as follows.

Q: As shown in Figure 1, a synchronous generator and motor are rated 100 MVA, 13.8 kV.??"=0.2per unit,…

Q: The one line diagram of a simple three bus power system is shown in figure Each generator is…

A: The fault occurred on bus 3 is a three phase fault. Three phase fault is a balanced fault (All…

Q: A 3-phase, 3-wire system has a normal voltage of 10-4 kV between the lines. It is supplied by a…

A: We have 3-Phase, 3-Wire system with, Normal Voltage (Vl) = 10.4 KV = 10.4 * 103 V Generator Positive…

Q: (b) Explain the steps involved in analysing balanced bolted fault in power system using Zbus method,…

A: Admittance matrix and impedence matrix is very important to analyze the power system .Admittance…

Q: 2) Draw equivalent diagram for this network with all per unit resistances and reactance near their…

A: The detection and diagnosis of faults in technical systems, particularly using a strategy in which…

Q: Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and…

Q: A 10 MVA, 6.9 kV alternator has a positive, negative and zero sequence per unit reactance components…

A: In this answer we will find the fault current in the case of a single line - ground fault as…

Q: FIGURE Q2 shows a four bus three phase power system. The generators, transformers and transmission…

Q: In a 3 phase, 3 wire system, it has normal voltage of 10.4kV line to line fault occurs at generator…

A: For the 3- phase line to line the positive sequence phase current is evaluated as:

Q: A 20 MVA, 11 kV, 3-phase, 50 Hz generator has its neutral earthed through a 5% reactor. It is in…

A: We have an 20 MVA 3-phase generator which has its neutral earthed through a 5% reactor . this…

Q: Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and…

A: Base MVA =150MVA Base Kv=13.8kV Xnewpu=Xold×MVAnewMVAold×KvoldKvnew2…

Q: Q1. A// Choose the correct answer: 1. One of the advantage of using a per unit system in power…

A: According to guidelines we are allowed to do only first 3 questions , please post again for…

Q: 6.1. A power system network is shown in Figure 47. The generators at buses 1 and 2 are represented…

A: The power system network is shown below,

Q: Line to ground fault has the highest probability in the power system True False

A: TRUE

Q: a power system what happens to phase voltages for a single line-to-ground fault as fault reactance…

A: Assume that fault occurs at phase 'a' if three phase system Although fault phase voltage…

Q: The positive sequence reactance for the power system shown in Figure below are in per unit on a…

A: Given: The positive sequence reactance for the power system shown in the Figure below is per unit on…

Q: All Choose the correct answer: 1. One of the advantage of using a per unit system in power system…

A: Per unit quantity is equal to the division of actual quantity and base quantity. There are two types…

Q: Q1. All Choose the correct answer: 1. One of the advantage of using a per unit system in power…

A: As per the guidelines of Bartley we supposed to answer first three subpart only.

Q: The bus impedance matrix of a 3-bus system is: [j0.2295 j0.1494 j0.1506] j0.1494 j0.1954 j0.1046…

A: We know that YBUS=[ZBUS]-1. So our YBUS is given as:…

Q: Contribution of fault analysis in power system netwrok?

A: Solution- Contribution of fault analysis in power system network- Fault analysis of a power system…

Q: Line to line to line fault is an asymmetrical type of fault in power system which occurs very…

A: Choose the correct option The given Statment Line to line to line fault is an asymmetrical type of…

Q: A 10 MVA, 6-6 kV, 3-phase star-connected alternator having a reactance of 20% is connected through a…

A: The last digits of student ID is 21. Given information We need to draw the transmission line and…

Q: A three-phase short circuit occurs at point P for the system shown in the following figure. (a)…

A: The most widely recognized kind of short out in a three-stage framework is a single conductor to…

Q: A 100-MVA, 20-kV synchronous generator is connected through a transmission line to a 100- MVA, 20-kV…

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

I. Draw the reactance diagram for the following power system in per unit using
base power = 50 MVA and base voltage = 15 KV in the generator side.
II. Calculate the fault current (If) in per unit and in ampere.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
Consider the single-line diagram of the power system shown in Figure 3.38. Equipment ratings are Generator 1: 1000MVA,18kV,X=0.2perunit Generator 2: 1000MVA,18kV,X=0.2p.u. Synchronous motor 3: 1500MVA,20kV,X=0.2p.u. Three-phase -Y transformers T1,T2,T3,T4,: 1000MVA,500kV,Y/20kV,X=0.1p.u. Three-phase YY transformer T5: 1500MVA,500kV,Y/20kVY,X=0.1p.u. Neglecting resistance, transformer phase shift, and magnetizing reactance, draw the equivalent reactance diagram. Use a base of 100 MA and 500 kV for the 50-ohm line. Determine the per-unit reactances.
Consider the single-Line diagram of a power system shown in Figure 3.42 with equipment ratings given: Generator G1: 50MVA,13.2kV,x=0.15p.u. Generator G2: 20MVA,13.8kV,x=0.15p.u. Three-phase -Y transformer T1: 80MVA,13.2/165YkV,X=0.1p.u. Three-phase Y- transformer T2: 40MVA,165Y/13.8kV,X=0.1p.u. Load: 40MVA,0.8PFlagging,operatingat150kV Choose a base of 100 MVA for the system and 132-kV base in the transmission-line circuit. Let the load be modeled as a parallel combination of resistance and inductance. Neglect transformer phase shifts. Draw a per-phase equivalent circuit of the system showing all impedances in per unit.
Determine the bus admittance matrix (Ybus) for the three-phase power system shown in Figure 6.23 with input data given in Table 6.11 and partial results in Table 6.12. Assume a three-phase 100 MVA per unit base. TABLE 6.11 Bus input data for Problem 6.20 TABLE 6.12 Partially Completed Bus Admittance Matrix (Ybus) for Problem 6.30
Determine the positive- and negative-sequence phase shifts for the three- phase transformers shown in Figure 3.36.
Equipment ratings for the five-bus power system shown in Figure 7.15 are as follows: Generator G1:Â Â Â Â 50Â MVA,Â 12kV,Â X=0.2 per unit Generator G2: 100Â MVA, 15 kV, X=0.2 per unit Transformer T1: 50 MVA, 10 kV Y/138kVY,X=0.10 per unit Transformer T2: 100 MVA, 15 kV /138kVY,X=0.10 per unit Each 138-kV line: X1=40 A three-phase short circuit occurs at bus 5, where the prefault voltage is 15 kV. Prefault load current is neglected. (a) Draw the positive-sequence reactance diagram in unit on a 100-MVA, 15-kV base in the zone of generator G2. Determine (b) the ThĂ©venin equivalent at the fault, (c) the subtransient fault current in per unit and in kA rms, and (d) contributions to the fault from generator G2 and from transformer T2.
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
With the same transformer banks as in Problem 3.47, Figure 3.41 shows the oneline diagram of a generator, a step-up transformer bank, a transmission line, a stepown transformer bank, and an impedan load. The generator terminal voltage is 15 kV (line-to-line). (a) Draw the per-phase equivalent circuit, aounting for phase shifts for positive-sequence operation. (b) By choosing the line-to-neutral generator terminal voltage as the reference, determine the magnitudes of the generator current, transmiss ion-line current, load current, and line-to-line load voltage. Also, find the three-phase complex power delivered to the load.
Three single-phase two-winding transformers, each rated 25MVA,34.5/13.8kV, are connected to form a three-phase bank. Balanced positive-suence voltages are applied to the high-voltage terminals, and a balanced, resistive Y load connected to the low-voltage terminals absorbs 75 MW at 13.8 kV. If one of the single-phase transformers is removed (resulting in an open connection) and the balanced load is simultaneously reduced to 43.3 MW (57.7 of the original value), determine (a) the load voltages Va,Vb, and Vc; (b) load currents Ia,Ib, and Ic; and (c) the MVA supplied by each of the remaining two transformers. Are balanced voltages still applied to the load? Is the open transformer overloaded?
Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances including the load impedance in per-unit. The data are given a follows: G:90MVA22kVx=0.18perunitT1:50MVA22/220kVx=0.10perunitT2:40MVA220/11kVx=0.06perunitT3:40MVA22/110kVx=0.064perunitT4:40MVA110/11kVx=0.08perunitM:66.5MVA10.45kVx=0.185perunit Lines I and 2 have series reactances of 48.4 and 65.43, respectively. At bus 4, the three-phase load absorbs 57 MVA at 10.45 kV and 0.6 power factor lagging.
How many transformers are needed to make an open-delta connection?
Consider the oneline diagram shown in Figure 3.40. The three-phase transformer bank is made up of three identical single-phase transformers, each specified by X1=0.24 (on the low-voltage side), negligible resistance and magnetizing current, and turns ratio =N2/N1=10. The transformer bank is delivering 100 MW at 0.8 p.f. lagging to a substation bus whose voltage is 230 kV. (a) Determine the primary current magnitude, primary voltage (line-to-line) magnitude, and the three-phase complex power supplied by the generator. Choose the line-to-neutral voltage at the bus, Va as the reference Account for the phase shift, and assume positive-sequence operation. (b) Find the phase shift between the primary and secondary voltages.