a. Write the command to enable IPv6 unicast routing in both routers (lmark) b. Enable OSPFv3 on all interfaces in Ibri router. c. Enable OSPFv3 on all interfaces in Dunk router. d. Write the command to display the routing table. e. Write the command to assign link-local address on interface Gig0/O of Ibri router. F.Write the command to verify OSPFv3 neighbors.

a. Write the command to enable IPv6 unicast routing in both routers (lmark) b. Enable OSPFv3 on all interfaces in Ibri router. c. Enable OSPFv3 on all interfaces in Dunk router. d. Write the command to display the routing table. e. Write the command to assign link-local address on interface Gig0/O of Ibri router. F.Write the command to verify OSPFv3 neighbors.

A+ Guide To It Technical Support

10th Edition

ISBN:9780357108291

Author:ANDREWS, Jean.

Publisher:ANDREWS, Jean.

Chapter7: Setting Up A Local Network

Section: Chapter Questions

Problem 5TC

See similar textbooks

Similar questions

Which of the following statements is true about routing functions? A router uses network addresses to forward messages. A router forwards DHCP frames at Layer 2. Both (A) and (B) are correct. None of the above are correct. 2) A WiFi access point is responsible for the following: Flow and error control. Identifying Network protocols. Multiple-access resolution. All of the above.
Please solve fast How many subnets are there? What are these subnets? How many interfaces does the router have? Give their IP addresses. The switch did not need any IP address. Why? Can PC-A get the MAC address of PC-C? If yes, how. Can PC-A get the MAC address of Router at interface g0/0? If yes, how. Indicate the source IP address, the destination IP address, the source MAC address, and the destination MAC address when PC-A sends a packet to PC-B. Indicate the source IP address, the destination IP address, the source MAC address, and the destination MAC address when PC-B sends a packet to a server outside the network with IP Address 125.124.12.135.
List all the static routes on each of the 4 routers required for full communication across the topology. The addresses with question marks have been relabeled. I think each router should have 3 static routes. This is using the ip route command (ip route <netid> <net mask> <next hop>)
In the context of DHCP what is the purpose of an IP helper address? a. The gateway for the computers in the segment b. Used to map private addresses in public ones for the purpose of accessing the outside c. Allows routers to forward DHCP requests to the segment where the server can be found d. It is a temporary IP address used by end-devices to issue requests to the DHCP server
q18- When the destination network is not listed in the routing table of a Cisco router, what is possible action that the router might take? Select one: A. The router forwards the packet to the interface indicated by the source address. B. The router forwards the packet toward the next hop indicated in the ARP table. C. The router discards the packet. D. The router sends an ARP request to determine the required next hop address.
Which of the following statements could be valid with respect to the ICMP (Internet Control Message Protocol)? a. It reports all errors which occur during transmission. b. A redirect message is used when a router notices that a packet seems to have been routed wrongly. c. It informs routers when an incorrect path has been taken. d. The "destination unreachable" type message is used when a router cannot locate the destination.
Question p 1. What TCP port did the old AOL IM program run on and was referenced in the PCAP challenge? 2. What switch would be used by tcpdump to limit the number of bytes captured by each packet? Full explain this question and text typing work only We should answer our question within 2 hours takes more time then we will reduce Rating Dont ignore this line
Assume that you have two computers and a router (default gateway) that have the following TCP/IP configuration and that Computer A wants to send data to Computer E. Match the addresses that will be used in the IP packet and the ethernet frame sent from Computer A. Computer A IP address: 178.23.43.12 Netmask: 255.255.0.0 Default gateway address: 178.23.17.1 MAC Address: 34:2A:C6:C6:55:C3 Computer E IP address: 178.23.54.23 Netmask: 255.255.0.0 Default gateway address: 178.23.10.1 MAC Address: 34:2A:C6:76:3E:12 Default Gateway MAC Address: 65:D3:C9:11:C5:99 Items to Match: IP packet Source IP address: IP packet Destination IP address: Ethernet frame Source MAC address Ethernet frame Destination MAC address Possible Values: 178.23.17.1 178.23.10.1 178.23.43.12 178.23.54.23 34:2A:C6:C6:55:C3 65:D3:C9:11:C5:99 34:2A:C6:76:3E:12
20)This command is used to display ARP table in a Cisco router. a. tracert b. ping c. show ip arp d. arp -c
Refer to the following dynamic NAT configuration. The router R1 has 2 interfaces with the following configurations: G0/0 – inside network – 10.1.1.1/24 S0/0/1 – outside network – 209.165.200.225/27 End users are complaining that they can not access the Internet and, as a network engineer, you have been asked by your manager to analyze the NAT configuration and fix the problem. What part of the configuration is most likely incorrect? How it can be fixed? R1(config)# ip nat pool nat-pool1 209.165.200.226 209.165.200.240 netmask 255.255.255.0 R1(config)# ip nat inside source list 1 pool nat-pool1 overload R1(config)#interface G0/0 R1(config-if)# ip address 10.1.1.1 255.255.255.0 R1(config-if)#ip nat inside R1(config)#interface S0/0/1 R1(config-if)# ip address 209.165.200.225 255.255.255.224 R1(config-if)#ip nat inside R1(config)#access-list 2 permit 10.1.1.0 0.0.0.255
You are provided two IP addresses, 192.168.15.15 and 192.168.16.15. Which answers below make the two IPs part of the same network and can communicate with each other without a router. Check all that apply A. Subnet 255.255.255.0 B. Subnet 255.255.0.0 C. Subnet 255.0.0.0 D. A and B E. B and C F. A, B, and C
Assume that the flags in a TCP packet are set in the order of [ cwr | ece | urg | ack | psh | rst | syn | fin ]. Write a Scapy command to perform "FIN" scan two ports 4000 and 4050 of the destination with IP address, "121.10.3.11". You should use a hexadecimal flag.