Q: Determine the variation in the width b as a function of x for the cantilevered beam that supports a ...
A: Solution: According to the question cantilevered beam that supports a uniform distributed load along...
Q: Your second customer wants to determine the required electrical power, which will be used to pump wa...
A:
Q: Derive a heat rate expression for the following geometry. Assume there is a poor contact at the junc...
A: Consider the diagram shown below for the given system.
Q: Locate the center of mass x̄ of the straight rod if itsmass per unit length is given by m = m0(1 + x...
A:
Q: A tank whose volume is unknown is divided into two parts by a partition. One side of the tank contai...
A: Given data: The type of refrigerant on one side is R-134a The volume of one side of tank is V1 = 0.0...
Q: Knowing that at the instant shown the angular velocity of bar AB is 15 rad/s clockwise and the angul...
A: Given AB Angular velocity = 15 rad/s EF Angular velocity = 10 rad/s To find The angular velocity of ...
Q: Which choice is the incompressible Navier–Stokes equation with constant viscosity?
A: Navier-Stoke’s equation with constant viscosity is The correct answer is option (d).
Q: Two 5-kg bars AB and BC are connected by a pin at B and by a spring DE . Knowing that the spring is ...
A: The free-body diagram of the system is shown below - Assume the following conditions,
Q: Argon is compressed in a polytropic process with n = 1.2 from 120 kPa and 30°C to 1200 kPa in a pist...
A: Write the expression of the polytropic process.
Q: F14-9. Draw Mohr's circle and determine the principal stresses. |30 MPa 30 MPa 40 MPa
A: Mohr circle will be given as:
Q: 14-95. The cylinder has a mass of 20 kg and is released from rest when h = 0. Determine its speed wh...
A: Write the expression of the potential energy of the mass.
Q: Assuming a steady-state laminar flow, calculate the permeability from the following measurement made...
A: Solution: Given data: The flow rate, Q = 2 cm3/sec The downstream fluid pressure, PD = 14.7 psi The ...
Q: What fluid property is responsible for the development of the velocity boundary layer? What is the e...
A: When a fluid flows over any stationary surfaces like flat plate, bed of a river or the wall of a p...
Q: Neglecting friction and the radius of the pulley, determine (a) the tension in cable ADB , (b) the r...
A: From the given diagram calculate the angles θ and β. Draw the F.B.D for the Beam ABC.
Q: Consider a classroom that is losing heat to the outdoors at a rate of 12,000 kJ/h. If there are 40 s...
A: Given, Qout = 12,000 kJ/h = 12,000/(3600) kJ/Sec = 3.33 kJ/Sec= 3.3 kW Heat Generated by Students(Qi...
Q: The A-36 steel bolt is tightened within a hole so that the reactive torque on the shank AB can be ex...
A: On applying torque equilibrium at the bolt,
Q: A 250 × 400-mm plate of mass 12 kg and a 300-mm-diameter pulley are welded to axle AC that is suppor...
A: Draw the free body diagram.
Q: explain how to find the resultant internal loading acting on the cross section at point A. Draw all ...
A: From the given figure and equation of equilibrium, the vector analysis is applied and can be written...
Q: Q1/The system contain from blocks A 24-kg and B 20-kg as shown when block B move downward with 0.6 m...
A: As per the guidelines we will solve the first three subparts for you. Consider the diagram shown b...
Q: Using the method of joints, determine the force in each member of the truss shown. State whether eac...
A: Draw the free body diagram of the whole truss and find the reactions: Apply static equilibrium cond...
Q: A vertical jet of water leaves a nozzle at a speed of 10 m/s and a diameter of 20 m. It suspends a p...
A:
Q: Use the law of sines and the law of cosines, in conjunction with sketches of the force polygons, to ...
A: Given F1 = 60 kip at 60o with x axis F2 = 25 kip at 75o with x axis F3 = 50 kip at 95o with F1 To fi...
Q: Rod AB is held in place by the cord AC . Knowing that c = 840 mm and that the moment about B of the ...
A: given data as per the question The moment at point B = 756 N·m considering free body diagram of the ...
Q: To unload a bound stack of plywood from a truck, the driver first tilts the bed of the truck and the...
A: Given Friction coefficient of plywood = 0.40 Friction coefficient of bed = 0.30 To find The smallest...
Q: List at least three other names for the material derivative, and write a brief explanation about why...
A: The material derivative is explained as the time rate change of physical quantities like momentum or...
Q: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, while sleeve CD...
A: (a) Write the relation to calculate the inner diameter of the sleeve CD using the given diagram. ...
Q: Does consideration of creep become important when materials are in service for long periods of time?
A: Creep: When a part of any member is subjected to constant stress at high temperature for a long per...
Q: Give examples of pump efficiency and turbine efficiency?
A: The range of the efficiency of a smaller centrifugal pump varies from 50 to 70 percent whereas for l...
Q: P9-3. The post weighs 8 KN/m. Determine the internal normal force in the post as a function of x. Pr...
A: Draw the free body diagram of the given section. 8 X (x) is the weight of the post section and Nx i...
Q: The car bumper is made of polycarbonate-polybutylene terephthalate. If E = 2.0 GPa, determine the ma...
A: Given data: Young’s modulus, E = 2GPa Moment of inertia, I = 300 X 106 mm4 Springs stiffness, ksp = ...
Q: The 50-mm-diameter A992 steel shaft is subjected to the torques shown. Determine the angle of twist ...
A: Given : d = 50 mm Solution : Assume clockwise as positive moment.
Q: F12-44. Determine the velocity of cylinder B if cylinder A moves downward with a speed of va = 4 ft/...
A: Given :
Q: State the rotational equation of motion.
A: Like translational motion, the displacement, velocity, and acceleration are also defined in rotation...
Q: A vertical piston–cylinder device initially contains 0.12 m3 of helium at 20°C. The mass of the pist...
A: To determine the exergy destruction, first, calculate the heat transfer. Write the expression of the...
Q: Refrigerant-134a is expanded isentropically from 600 kPa and 70°C at the inlet of a steady-flow turb...
A: Given Data: The inlet pressure of the refrigerant R-134a is P1 = 600 kPa. The inlet temperature of ...
Q: Two boy A and B running in the opposite direction in adjacent lanes, at t=0, boy A accelerates at a ...
A: (a) Given : Solution : Solution : The distance between two points A & B is calculated as :
Q: A 4-L pressure cooker has an operating pressure of 175 kPa. Initially, one-half of the volume is fil...
A: Consider this system as a control volume system. The energy associated with the fluid is internal en...
Q: Define the Nonmechanical Forms of Work.
A: In thermodynamics, the non-mechanical work is the work which is determined by the non-contact or the...
Q: 18-11. The force of T = 20 N is applied to the cord of negligible mass. Determine the angular veloci...
A: Given: The force applied on the cord, T = 20 N The mass of the wheel, m = 20 kg The number of revolu...
Q: Two identical uniform boards, each with a weight of 40 lb, are temporarily leaned against each other...
A: Consider the free body diagram shown below for the given system.
Q: Four 3-kg packages are held in place by friction on a conveyor which is disengaged from its drive mo...
A: Total vertical distance between block 1 and 4 is 2.4m So vertical distance between blocks be 0.8m (2...
Q: Express the compatibility conditions in terms of the displacements caused by the loading?
A: The compatibility condition is based on the fact that any change in length of the bar must be compat...
Q: What is the mean effective pressure for the cycle
A: Mean effective pressure is defined with respect to the Otto cycle. It is defined as the imaginary pr...
Q: Define Some basic pressure gages.
A: The pressure gauges are broadly classified into three types: Hydrostatic Gauges Aneroid Gauges Spin...
Q: The aluminum rod AD is fitted with a jacket that is used to apply a hydrostatic pressure of 6000 psi...
A: The data given is, Stress in x-direction, ?x = -6000 psi Stress in y-direction, ?y = 0 Stress in z-...
Q: Draw shear and bending moment diagram for the beam ABC, and determine the compressive load P to be c...
A:
Q: A wheel has an angular acceleration of a = (0.5 u) rad/s2, where u is in radians. Determine the magn...
A: Given The angular velocity of the disk can be determined by Velocity at point P can be determined ...
Q: please i want solution with full steps
A: From Mohr’s diagram. Draw the stress element.
Q: A piston–cylinder device contains 2.2 kg of nitrogen initially at 100 kPa and 25°C. The nitrogen is ...
A: Given, Mass of Nitrogen (m) = 2.2 Kg P1 = 100kPa T1 = 25°C=25+273=298K PV1.3 = Constant
A bar with surface temperature (310) oC and diameter (9.5) mm, temperature 20
oC and heat convection
It is contained in a fluid with a coefficient of 95 W / m2K. The top of this bar is heat conduction
It is desired to be coated with bakelite with a coefficient of 2.5 W / mK up to the critical radius thickness.
a) the critical radius of the bakelite coating and the heat transfer at the critical radius per unit length.
Found it. b) heat transitions per unit length for uninsulated and bakelite (insulation) coated rod
You calculate. Comment the results
Step by step
Solved in 4 steps with 9 images
- An electronic device that internally generates 600 mW of heat has a maximum permissible operating temperature of 70C. It is to be cooled in 25C air by attaching aluminum fins with a total surface area of 12cm2. The convection heat transfer coefficient between the fins and the air is 20W/m2K. Estimate the operating temperature when the fins are attached in such a way that (a) there is a contact resistance of approximately 50 K/W between the surface of the device and the fin array and (b) there is no contact resistance (in this case, the construction of the device is more expensive). Comment on the design options.Estimate the rate of heat loss per unit length from a 5-cm ID, 6-cm OD steel pipe covered with high-temperature insulation having a thermal conductivity of 0.11 W/(m K) and a thickness of 1.2 cm. Steam flows in the pipe. It has a quality of 99% and is at 150C. The unit thermal resistance at the inner wall is 0.0026(m2K)/W the heat transfer coefficient at the outer surface is 17W/(m2K) and the ambient temperature is 16C.One end of a 0.3-m-long steel rod is connected to a wall at 204C. The other end is connected to a wall that is maintained at 93C. Air is blown across the rod so that a heat transfer coefficient of 17W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38C, what is the net rate of heat loss to the air?
- 1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.The handle of a ladle used for pouring molten lead is 30 cm long. Originally the handle was made of 1.9cm1.25cm mild steel bar stock. To reduce the grip temperature, it is proposed to form the handle of tubing 0.15 cm thick to the same rectangular shape. If the average heat transfer coefficient over the handle surface is 14 W/m K, estimate the reduction of the temperature at the grip in air at 21C.2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
- A high-speed computer is located in a temperature-controlled room at 26C. When the machine is operating, its internal heat generation rate is estimated to be 800 W. The external surface temperature of the computer is to be maintained below 85C. The heat transfer coefficient for the surface of the computer is estimated to be 10W/m2K. What surface area would be necessary to assure safe operation of this machine? Comment on ways to reduce this area.2.9 In a large chemical factory, hot gases at 2273 K are cooled by a liquid at 373 K with gas-side and liquid-side convection heat transfer coefficients of 50 and , respectively. The wall that separates the gas and liquid streams is composed of a 2-cm thick oxide layer on the gas side and a 4-cm thick slab of stainless steel on the liquid side. There is a contact resistance between the oxide layer and the steel of . Determine the rate of heat loss from hot gases through the composite wall to the liquid.3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
- 2.43 A turbine blade 6.3 cm long, with cross-sectional area and perimeter , is made of stainless steel . The temperature of the root, , is . The blade is exposed to a hot gas at , and the heat transfer coefficient is K. Determine the temperature of the blade tip and the rate of heat flow at the root of the blade. Assume that the tip is insulated.2.30 An electrical heater capable of generating 10,000 W is to be designed. The heating element is to be a stainless steel wire having an electrical resistivity of ohm-centimeter. The operating temperature of the stainless steel is to be no more than 1260°C. The heat transfer coefficient at the outer surface is expected to be no less than in a medium whose maximum temperature is 93°C. A transformer capable of delivering current at 9 and 12 V is available. Determine a suitable size for the wire, the current required, and discuss what effect a reduction in the heat transfer coefficient would have. (Hint: Demonstrate first that the temperature drop between the center and the surface of the wire is independent of the wire diameter, and determine its value.)2.45 Heat is transferred from water to air through a brass wall . The addition of rectangular brass fins, 0.08 cm thick and 2.5 cm long, spaced 1.25 cm apart, is contemplated. Assuming a water-side heat transfer coefficient of and an airside heat transfer coefficient of , compare the gain in heat transfer rate achieved by adding fins to (a) the water side, (b) the air side, and (c) both sides. (Neglect temperature drop through the wall.)