A0.11-kg bullet is fired with a velocity of 76.3 m/s into a solid cylinder of mass 23.1 kg and radius 0.41 m. The cylinder is initially at rest mounted on a fixed vertical axis that runs through its center of mass. The line of motion of the bullet is perpendicular to the axis and at a ed = 0.0013 m from the center. Find the angular speed of the system after the bullet strikes and adheres to the surface of the cylinder. Vo, Axis 00

A0.11-kg bullet is fired with a velocity of 76.3 m/s into a solid cylinder of mass 23.1 kg and radius 0.41 m. The cylinder is initially at rest mounted on a fixed vertical axis that runs through its center of mass. The line of motion of the bullet is perpendicular to the axis and at a ed = 0.0013 m from the center. Find the angular speed of the system after the bullet strikes and adheres to the surface of the cylinder. Vo, Axis 00

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a slender rod AB with a length l and a mass m. The ends are connected to blocks of negligible mass sliding along horizontal and vertical tracks. If the rod is released with no initial velocity from a horizontal position as shown in Fig.A, determine its angular velocity after it has rotated through an angle of θ (see Fig B) using the conservation of energy method. (Hint: Moment of inertia of rod about G = (1/12)ml2 The kinetic energy of a rigid body in plane motion is
A particle of mass 0.102 kg is rotating at 840 rpm at a radius of 135 mm. At t=2 the radius begins to expand at a rate of 14 mm.s-1. What is the radial force at t=1.9s [N] What is the arc length traveled by the mass at t=1.9 s? [m] What is the transverse force on the mass at t=4s? [N]
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. The wooden block (mass m = 0.5358 kg) is released from rest at A by a compressed spring (compressed length 0.6 m, undeformed length 1 m, spring constant k = 150 N/m). The block is allowed to slide through the rough horizontal surface (A to B), then along the smooth circular ramp (B to C, central angle θ = 47.2°, until the block is released after point C. Calculate the speed of the block at points B and C. Also, what is the magnitude of the normal force exerted to the block just before the block leaves the ramp? Neglect the geometry of the block. NOTE: Use Work-Energy Method to solve for the speeds; use Force-Mass-Acceleration (FMA) Method to compute for the normal force.
A hoop of radius 95mm and mass 100g is rotated via a capacitor driven power source with P(t)=1.61e-1.3tW. (since it is a hoop, it is a special case, and r=rG) Assuming the hoop is accelerated from rest, determine the rotational velocity after t=8.5s. [rad.s-1] Determine the rotational speed of the hoop after t=8.5s if the power source acts to roll the particle from rest on a horizontal surface. [rad.s-1]
The figure shows a small piece of clay colliding into a disk. The disk is initially at rest, but can rotate about a pivot fixed at its center. The collision is completely inelastic.The disk has mass M = 4.73 kilograms and radius R = 0.755 meters. The clay has mass m = 279 grams and is moving horizontally at vi = 3.66 m/s just before colliding with and sticking to the disk. The clay strikes the edge of the disk at a location of b = 0.505 meters offset from the center of the disk. Note that the size of the clay is negligible compared to the radius of the disk. Calculate the angular velocity (rad/s) of the disk just after the collision.
Two blocks with masses m1 = 5.0 kg and m2 = 7.0 kg are attached by a string as shown in the figure below, over a pulley with mass M = 2.0 kg. The blocks are released from rest. The pulley, which turns on a frictionless axle, is a hollow cylinder with radius 0.050 m over which the string moves without slipping. The horizontal surface is frictionless. Find the speed of the system when the block of mass m2 has dropped 2 m.
A prop shaft of a heavy-duty truck has two bearings which are positioned at 3 metres from each other. The shaft must rotate at 30 rad/s when the truck travels at the speed of 40 m/s. Such a shaft carries two masses of (MA = 10 kg) and (MB = 5 kg) acting at the extremities of the arms 0.45 m and 0.6 m long, respectively. The planes in which these masses rotate are 1.2 m and 2.4 m respectively, from the left end bearing supporting the shaft. The angle between the arms is 60°. If the masses are balanced by two counter-masses (named X and Y) rotating with the shaft acting at a radius of 0.3 m and placed at 0.3 m from each bearing centre:
A locomotive consists of multi cylinder reciprocating engine running at a speed of 8 r.p.s having a stroke length of 25cm, which carries a mass of reciprocating part whose magnitude is 8kgs with a revolving part of 4kgs rotating at 17cm radius. If two third of the reciprocating parts and all the revolving parts are to be balanced, determine the following when the crank has rotated 560 from top dead centre to bottom dead centre. 1. Maximum primary unbalanced force of reciprocating mass in newtons 2. Balancing mass required at a radius of 35cm in kgs 3. Variation of maximum & minimum tractive force in newtons 4. Variation of maximum & minimum swaying couple for the given centre distance 72cm between the two cylinders in (N-m) 5.…
A small 2-lb ball B is rotating (Fig.13) at angular speed w1 of (6+(0.1*26)) rad/sec about a horizontal shaft. The ball is connected to the bearings with light elastic cords which when unstretched are each 12 in. in length. A force of 15 lb is required to stretch the cord. The distance d1 between the bearings is originally 20 in. If the bearing A is moved to shorten d by 6 in, what is the angular velocity w2 of the ball? Neglect the effects of gravity and the mass of the elastic cords. Use the moment of momentum equation.
A 0.005 00-kg bullet traveling horizontally with a speed of 1.00 3 103 m/s strikes an 18.0-kg door, embedding itself 10.0 cm from the side opposite the hinges as shown in Figure P11.30. The 1.00-m wide door is free to swing on its frictionless hinges. (a) Before it hits the door, does the bullethave angular momentum relative to the door’s axis of rotation? (b) If so, evaluate this angular momentum. If not, explain why there is no angular momentum. (c) Is the mechanical energy of the bullet–door system constant during this collision? Answer without doing a calculation. (d) At what angular speed does the door swing open immediately after the collision? (e) Calculate the total energy of the bullet–door system and determine whether it is less than or equal to the kinetic energy of the bulletbefore the collision. (f) What If? Imagine now that the door is hanging vertically downward, hinged at the top, so that as shown is a side view of the door and bullet during the collision. What is the…
John played croquet with a 0.922-kg. mallet head and you can assume that it can be modelled as a point mass for simplified analysis only in this case. Meanwhile, the mallet's handle has a length of 0.95 m and a mass of 0.63 kg. Helifts the mallet from the ground and swings it down, pivoting around her grasp, to strike the croquet ball. The ball, which is initially at rest, weighs 0.42 kilograms and it has linear velocity of 1.995 meters per second to the right immediately after impact. 1. Which of the following is the most ideally constructed momentum-impulse diagram for the system of croquet ball and mallet together 2. What is the kinematic relationship relating the velocity of the mass center of mallet handle AB vG and its angular velocity ω?
The 30-g bullet is fired horizontally at 1000 m/s into the 300-g block resting on a smooth surface. If the bullet becomes embedded in the block, what is the velocity of the block immediately after impact ?.