100 mm Consider the propeller tube shown in The density of air is Pa = 1.23 kg/m. The diameter of the nozzles at B, C, D, and Eis 100 mm 0.5 m M 60 rad/s 0.5 m 0.5 m 05 m Part A If the propeller tube rotates at a constant rate of 60 rad/s when 1.80 kg/s of air enters at A, determine the frictional torque M acting on the tube. Express your answer to three significant figures and include the appropriate units. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise.

100 mm Consider the propeller tube shown in The density of air is Pa = 1.23 kg/m. The diameter of the nozzles at B, C, D, and Eis 100 mm 0.5 m M 60 rad/s 0.5 m 0.5 m 05 m Part A If the propeller tube rotates at a constant rate of 60 rad/s when 1.80 kg/s of air enters at A, determine the frictional torque M acting on the tube. Express your answer to three significant figures and include the appropriate units. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pipe elbow below discharges water at rate of SN/100 (m3/s) into the atmosphere at section 2. The total volume of the passage between sections 1 and 2 is equal to 0.2 m3 and the total mass of the elbow material between sections 1 and 2 is equal to 10 x SN (kg). Neglect any friction losses. Calculate the horizontal and vertical forces acting on the elbow. Also, calculate the resultant force and angle of force on the elbow. ****SN=21
A horizontal pipe bend with a deflection angle of 120o has an entrance diameter of 300 mm and exit diameter of 100 mm. Oil with a density of 860 Kg/m3 enters at the rate of 3.6 m/s and at a pressure of 180 KPa. Determine the magnitude of the force required to hold the bend in place for (a) smooth flow; (b) a situation where head loss is 0.05(v100-v300) 2/2g.
A U-tube acts like a water siphon. The elbow in the tube is 1 m above the water surface, the tube outlet is L from point A below. When the length L is 5 m, the water emerges from the bottom of the siphon as free jet at atmospheric pressure. Determine the speed of the free jet and the minimum absolute pressure of the water at the elbow. (Patm= 101325 Pa, dsu=1000 kg/m3)
Air is flowing in a circular duct. The air flow rate is Q=2000 ft3/min. The diameter of the duct is D=14 in. (2) Determine the friction loss per 100 ft, hL_________inH2O
A reducing bend with an inlet diameter of 200 mm and exit diameter of 150 mm bends 40 degreesupwards. The water velocity and corresponding pressure at the inlet to the band is 4, 5 m/s and 70 kParespectively. Determine the weight flow, the water flow velocity at the exit to the bend, the bend exitpressure if the friction head loss through the bend section is 2 m and the magnitude and direction ofthe resultant force flowing through the bend.
Water is discharging through a circular orifice plate 25mm in diameter in the vertical side of the tank of a constant plan area 0.4m2. It is observed that the time taken for the water level to fall from 1.5m to 1.4m above the orifice is24.5 seconds. Show that the average volumetric flow rate is 1.633*10^-3 m^3/s.By approximating the height as being a constant value (1.4m, 1.5m or 1.45m) for discharge rate calculation, estimate the coefficient of discharge for this orifice plate, and give highest and lowest plausible values from the data supplied.
A pipe whose axis is horizontal, is full of water in motion. At a section A, the velocity of water is recorded as 54000dm/hrandd the pressure is equilavent tp 14.07m of water. if the pipe tapers gradually from 150mm diameter to A to 100mm diameter at B. determine the preesure at B.
Determine the maximum allowable suction head for a pump with a cavitation constant equal to 0.3 when the total dynamic head is 40 m. Assume that the pump is to operate at sea level and a temperature of 25°C. Patm is 101.3 kN/m2 at 25°C; Pvapor is 3.17 kN/m2 at 25°C and the specific weight of water is 9.78 kN/m³ at 25°C.
A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference betwoen the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine the anchoring force needed to hold the elbow in place A) 27 N 3433.5 N C) 79.5 N D) 132. 9 E) 106. 5 N
A hydroelectric power plant uses Pelton-type turbines, in which multiple nozzles are used to accelerate the waterwhich is directed onto the turbine blades, which are exposed to an atmospheric pressure of 101.325 kPa. The water enters the nozzles with an absolute pressure of 500 kPa and a speed of 5 m/s, and the nozzle outlets are exposed to atmospheric pressure and have an internal diameter of 5 cm. Consider that the specific mass of water is 1,000 kg/m3. Determine the mass flow rate of water through each of the nozzles, and explain why the actual mass flow rate will be lower.
A 20 hp pump with a suction from an open reservoir (10 m abovethe pump) has a flow rate of 125 m3/hr and a suction pipe of 150mm diameter. Determine the discharge pressure of the pump if itpumps water to a tank 15 m above the pump. Discharge pipediameter of the pump is 100 mm.
The impeller of a centrifugal blower has a radius of 15 cm and a blade width of 6.1 cm at the inlet, and a radius of 30 cm and a blade width of 3.4 cm at the outlet. The blower delivers atmospheric air at 20°C and 95 kPa. Disre- garding any losses and assuming the tangential components of air velocity at the inlet and the outlet to be equal to the impeller velocity at respective locations, determine the volu- metric flow rate of air when the rotational speed of the shaft is 800 rpm and the power consumption of the blower is 120 W. Also determine the normal components of velocity at the inlet and outlet of the impeller.