a1/ The power of 6-blade flat blade turbine agitator in a tank is a function of diameter of impeller, number of rotations of the impeller per unit time, viscosity and density of liquid. From a dimensional analysis, obtain a relation between the power and the four variables.

a1/ The power of 6-blade flat blade turbine agitator in a tank is a function of diameter of impeller, number of rotations of the impeller per unit time, viscosity and density of liquid. From a dimensional analysis, obtain a relation between the power and the four variables.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.70P

See similar textbooks

Related questions

Q: A liquid of density ? and viscosity ? flows by gravity through a hole of diameter d in the bottom of…

A: The relationship of functional variables for the given problem is as follows: The dimensions of all…

Q: The thrust force, F generated by a propeller is found to depend on the following parameters:…

Q: 17. The moment of viscous liquid between two cylinder depend on angular velocity o of internal…

Q: Use dimensional analysis to convert the quantity to the indicated units. 24 in. to ft

Q: C1 (a). A lubricating oil having the dynamic viscosity of 0.052 poise and kinematic viscosity of…

A: Given Data: Dynamic viscosity=0.052 poise Kinematic viscosity=0.19 stokes

Q: The power P required to drive a propeller is known to depend on the diameter of the propeller D, the…

A: Write the dimension of the variables used for a particular propeller.

Q: Example: The pressure difference (Ap) between two point in a pipe due to turbulent flow depends on…

A: ∆P=fV, D, μ, ρ ,e, L

Q: Potide Use Buckingham's Pi Theorem to determine non-dimensional parameters in the phenomenon shown…

A: Variables are ∆P, R, σs.

Q: The drag coefficient in aircraft industry affected by some parameters which are the speed of plane…

A: DRAG COEFFICIENT Drag Force (D) is defined as the force that opposes the motion of a fluid-filled…

Q: Power generated by a propeller operating in the air (P); it depends on the mass density of the air…

Q: a) i. Define dimensional constant. ii. Define non-dimensional variable. b) When a liquid in a beaker…

A: We have given

Q: Task 2 Evaluate the use of dimensionless analysis using the Buckingham Pi Theorem for a given fluid…

Q: A lubricating oil having the dynamic viscosity of 0.051 poise and specific gravity of 1.12.…

Q: dus A fluid flow situation depends the on 2. Velocity (V), the density several linear dimension,…

A: Variables involved in this case,Velocity = VDensity =ρLinear dimensions=L, L1, L2Pressure…

Q: 1 ft/min=_____ ft/h using dimensional analysis

Q: The force, F, acting on a billboard due to wind depends on it length, l, height, h, the modulus of…

A: As it is given in the question that the force (F) depends in l, h, E, and γa. Here are the…

Q: Q2:- If the velocity of flow v, dynamic viscosity u, bulk modulus of elasticity K and diameter of…

Q: 1.5 The power generated by a pump PE is a function of the volumetric flow rate Q, the height of…

Q: Q2: The power input P to a centrifugal pump is assumed to be a function of the volume flow Q,…

A: given :- The power input P to a centrifugal pump is assumed to be a function of the volume flow Q,…

Q: Q2:- If the velocity of flow v, dynamic viscosity a, bulk modulus of elasticity K and diameter of…

A: ,

Q: The quantities viscosity u, velocity V, and surface tension Y may be combined into a dimensionless…

Q: Andrade's equation is a proposed model of the effect of temperature on viscosity written as, H =…

A: Given: The Andrade's equation is, μ=DeBT Here, μ is the dynamic viscosity of water and T is the…

Q: A vacuum cleaner creates a pressure drop Ap across its fan. Relate this pressure drop to the…

Q: (d) The force, F, of a turbine generator is a function of density p, area A and velocity v. By…

A: d) The dimensions of the variables are given by,

Q: 4.1 Use the Buckingham a method to develop an expression for the viscous torque T produced on a disc…

A: 4.1 The given system is - T = fD,N,μ,ρ The total variables is 5 (including T) . TTorque=ML2T-2, D=L,…

Q: Q3: The power output (P) of a marine current turbine is assumed to be a function of velocity U,…

A: Given that The power output (P) of a marine current turbine is assumed to be a function of velocity…

Q: The drag FD of the golf ball is affected by the speed V of the ball, the diameter d of the ball, the…

Q: When fluid in a pipe is accelerated linearly from rest, it begins as laminar flow and then undergoes…

A: Given Diameter of the pipe = D Acceleration = a Density = ρ Viscosity = µ Time = ttr To find…

Q: The thrust F of a propeller is generally thought to be afunction of its diameter D and angular…

A: The thrust force is the function of F=fD,ω,V,μ,ρ here n=6m=3 Now the replacing variables are μ,V,D…

Q: By dimensional analysis, obtain an expression for the drag force (F) on a partially submerged body…

A: Given Force = F Velocity = u Length = L Roughness = e Density of fluid = p Gravitational…

Q: The pressure drop AP in flow through pipes per unit length is found to depend on the average…

Q: A- The power produced from a pump (P) is fun (Hon of flow (@), pressure drop (P), Density of fluid…

Q: Using dimensional analysis, derive a relation to evaluate the headloss, hf, in closed conduits…

A: given; Using dimensional analysis, derive a relation to evaluate the head loss, hf, in closed…

Q: The pressure coefficient is defined by the ratio between the static pressure difference and the…

Q: C1 (a). A lubricating oil having the dynamic viscosity of 0.051 poise and specific gravity of 1.12.…

A: Given data: Dynamic viscosity of oil, µ = 0.051 poise. The specific gravity of oil, SGoil = 1.12.…

Q: A2) In order to solve the dimensional analysis problem involving shallow water wave as in Figure 2,…

Q: The quantities viscosity µ, velocity V, and surface tension Y may be combined into a dimensionless…

Q: 10A plate 0.05mm distant from a fixed plate moves at 1.25 m/s and required a force per unit area of…

A: GIVEN DATA- 1(a) SHEAR STRESS =2.2N/m2 , U=1.25 m/s , y=0.05mm , Specific gravity of oil =0.7 1(b)…

Q: The efficiency (n) of a fan depends upon density (p), and dynamic viscosity (µ) of the fluid,…

Q: Q.2. The force of impeller depends on the volumetric flowrate of fluid (Q) through the pipe of…

A: Buckingham pie theorem - if there are "n" variables in any physical phenomenon , whether dependent…

Q: For a venturi meter given below, the volumetric flow rate is defined in terms of the geometrical…

A: Venturi Meter is a device in which pressure energy is converted into kinetic energy and it is used…

Q: 1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area…

Q: Dimensional analysis is to be used to correlate data on bubble size with the properties of the…

Q: The drag force Dp acting on a spherical particle that falls very slowly through a viscous fluid is a…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

When a sphere falls freely through a homogeneous fluid, it reaches a terminal velocity at which the weight of the sphere is balanced by the buoyant force and the frictional resistance of the fluid. Make a dimensional analysis of this problem and indicate how experimental data for this problem could be correlated. Neglect compressibility effects and the influence of surface roughness.
Dimensional analysis is to be used to correlate data on bubble size with the properties of the liquid when gas bubbles are formed by a gas issuing from a small orifice below the liquid surface. Assume that the significant variables are bubble diameter D, orifice diameter d, liquid density rho, surface tension sigma (in N/m), liquid viscosity mu, and g. Select d, rho, and g as the core variables.
The time t d to drain a liquid from a hole in the bottom of atank is a function of the hole diameter d , the initial fluidvolume y 0 , the initial liquid depth h 0 , and the density ρ andviscosity μ of the fluid. Rewrite this relation as a dimensionlessfunction, using Ipsen’s method.
Using primary dimensions, verify that the Rayleigh number is indeed dimensionless. What other established nondimensional parameter is formed by the ratio of Ra and Gr?
Books on porous media and atomization claim that the viscosityμ and surface tension Y of a fl uid can be combinedwith a characteristic velocity U to form an important dimensionlessparameter. ( a ) Verify that this is so. ( b ) Evaluatethis parameter for water at 20°C and a velocity of3.5 cm/s. Note: You get extra credit if you know the nameof this parameter.
During World War II, Sir Geoffrey Taylor, a British fl uiddynamicist, used dimensional analysis to estimate theenergy released by an atomic bomb explosion. He assumedthat the energy released E , was a function of blast waveradius R , air density ρ, and time t . Arrange these variablesinto a single dimensionless group, which we may term theblast wave number .
Determine the form of an equation for the distance (s) that a sphere will fall in time t, if it starts with an initial velocity and the resistance of the fluid through which it falls is taken into consideration. Resistance is dependent upon the density (ρ) and viscosity (μ) of the medium and the diameter (d) and mass (m) of the sphere. Hence in addition to g, v and t these factors are incorporated. S = f (g, v, t, m, d, ρ, μ) USE DIMENSIONAL ANALYSIS AND BUCKINGHAM PI THEOREM
Taylor number (Ta) is used here to describe the ratio between the inertia effect andthe viscous effect. By applying Buckingham Pi’s Theorem, determine an equation forTa as a function of the radius of inner cylinder (r), cylinder tangential velocity (v),fluid dynamic viscosity (μ), gap distance (L) and fluid density (ρ).
A dimensionless combination of variables that is important in the study of viscous flow through pipes is called the Reynolds number, Re, defined as ???/? where, as indicated in Fig. 11, ? is the fluid density, V the mean fluid velocity, D the pipe diameter, and the fluid viscosity. A Newtonian fluid having a viscosity of 0.38 ? . ?/?² and a specific gravity of 0.91 flows through a 25‐mmdiameter pipe with a velocity of 2.6 ?/?. Determine the value of the Reynolds number using (a) SI units, and (b) BG units.
When a capillary tube of small diameter D is inserted into a container of liquid, the liquid rises to height h inside the tube (Fig.). h is a function of liquid density ? , tube diameter D, gravitational constant g, contact angle ?, and the surface tension ?s of the liquid. (a) Generate a dimensionless relationship for h as a function of the given parameters. (b) Compare your result to the exact analytical equation for h. Are your dimensional analysis results consistent with the exact equation? Discuss.
The thrust F of a propeller is generally thought to be afunction of its diameter D and angular velocity V , the forwardspeed V , and the density ρ and viscosity μ of the fl uid.Rewrite this relationship as a dimensionless function.
An automobile has a characteristic length and area of 8 ft and 60 ft2, respectively. When tested in sea-level standard air, it has measured velocities of 20, 40, and 60 mi/h and drag forces of 31, 115, and 249 lbf, respectively. The same car travels in Colorado at 115 mi/h at an altitude of 3500 m. Using dimensional analysis, estimate its drag force (in lbf). Using dimensional analysis, estimate the horsepower required to overcome air drag (in hp)