Q2:- If the velocity of flow v, dynamic viscosity a, bulk modulus of elasticity K and diameter of pipe D, using dimensional analysis, determine the general form of relationship between these variables.

Q2:- If the velocity of flow v, dynamic viscosity a, bulk modulus of elasticity K and diameter of pipe D, using dimensional analysis, determine the general form of relationship between these variables.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.13P: 5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its...

See similar textbooks

Related questions

Q: The sketch shows an oil manometer that is connected between two pipes which transport water. The…

A: Given, h1=0.17 mh2=350 mm=0.35 mh3=15 cm=0.15 m The specific gravity of the oil, γo=0.76 The density…

Q: The Power (P) required to drive the pump depends upon the diameter (D), the angular velocity (@),…

A: Total variable =P,D,ω,Q,ρ P= f(D,ω,Q,ρ) where P is a dependent variable

Q: C1 (a). A lubricating oil having the dynamic viscosity of 0.058 poise and specific gravity of 1.11.…

Q: 1. Figure below fluid A is water, fluid B is oil (s = 0.85). Determine the pressure difference…

Q: Example: The pressure difference (Ap) between two point in a pipe due to turbulent flow depends on…

A: ∆P=fV, D, μ, ρ ,e, L

Q: The thrust P of a propeller depends upon diameter (D); speed (u) through a fluid density (p);…

A: Given data: P = f (D,u,N,ρ,μ) To determine: The above mentioned non-dimensional correlation

Q: 3.26 Water flows downward along a pipe that is inclined at 30° below the horizontal, as shown.…

A: Given data: Water pipe angle (θ) = 300, Length of the pipe (L) = 1.5 m, Height (h)…

Q: 1 For pumps and turbines, mechanical efficiency is expressed as A. Power input/Fower output B. Power…

A: Answer: ◆ Question 1: The correct answer is option (B). ◆ Question 2: The correct answer is option…

Q: Q1: Calculate the dynamic viscosity of an oil, which is used for lubrication between a rectangular…

Q: 1- The thrust (P ll i) of a propeller depends upon diameter (D); speed (u) through a fluid density…

A: The dimensional formula for each is as shown below.

Q: 1 ft/min=_____ ft/h using dimensional analysis

Q: The variables in a Saybolt viscometer are the time (t) required to empty a certain volume of oil of…

A: The dimensional formula for each variable is shown below.

Q: Q2:- If the velocity of flow v, dynamic viscosity u, bulk modulus of elasticity K and diameter of…

Q: The quantities viscosity u, velocity V, and surface tension Y may be combined into a dimensionless…

Q: In the figure shown, what is the static pressure in kPa in the air chamber? Write the value of your…

A: Given information, Height of individual fluids, Find Pressure in the air

Q: Q3: An infinite plate is moved over a second plate on a layer of liquid as shown in figue (4) .For…

A: Note- As per our company's guidelines we are allowed to answer only first three subparts. kindly…

Q: Andrade's equation is a proposed model of the effect of temperature on viscosity written as, H =…

A: Given: The Andrade's equation is, μ=DeBT Here, μ is the dynamic viscosity of water and T is the…

Q: Q1/ The angular velocity n of a car wheel was found to be a function of its height H as compared to…

Q: (d) The force, F, of a turbine generator is a function of density p, area A and velocity v. By…

A: d) The dimensions of the variables are given by,

Q: Q1: If an air stream flowing at velocity (U) pasta body of length (L) causes a drag force (F) on the…

A: Force is dependent on the body U,L and fluid viscosity μ Now, we write the dimension formulae of…

Q: The pressure drop (Ap) test is carried out using a pipe configuration as illustrated below:…

Q: Determine whether the following equations are dimensionally homogeneous. 2ph3 mh + 3t2 f : || f is a…

A: Given equation is f=2ph3l+mh3t2 Here, f is the force, h and l is the velocity, m is a mass, t is a…

Q: Task 1 (d) The force, F, of a turbine generator is a function of density p, area A and velocity v.…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: Q2 :-If the velocity of flow over surface v, Surface tension o, density of flowp length of surface…

Q: Q2: For Ethanol container shown In the following figure, compute x and y if the gage pressure reads…

Q: the viscosity of a liquid having kinematic viscosity 5 stokes and specific gravity 1.6 is ------ a)…

A: Data given- Kinematics viscosity = 5 stakes = 5 × 10-4 m2/s Specific gravity = 1.6

Q: Q1: Calculate the dynamic viscosity of an oil, which is used for lubrication between a rectangular…

A: The free-body diagram of the rectangular plate will be given as follows,

Q: An infinite plate is moved over a second plate on a layer of liquid as shown in figue (4) .For small…

A: Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts of a…

Q: A block of weight W is being pulled over a table by another weight Wo, as shown in Fig. P1.60. Find…

Q: The volume flow in a water pipe is 9000 m°/h. The pipe length is 80 m, the pipe diameter 1 m. The…

Q: If a certain liquid has viscosity 4.9 × 10¬³ N s/m² and kinematic viscosity 3.49 × 10' stokes, its…

Q: Convert a viscosity of 61 g/(cm s) to lbf/(hr ft2). Use dimensional analysis in cancellation of…

Q: 2- The resistance (R) experienced by a partially submerged body depends upon the velocity (u),…

A: Given:R=Resistance experienced by the partially submerged body,u=velocity of the body,L=length of…

Q: The quantities viscosity µ, velocity V, and surface tension Y may be combined into a dimensionless…

Q: Q1: Ah/L is the loss of pressure in meter per unit length through a pipe and it depends on velocity…

A: Δhl represent the loss of pressure per meter length of pipeΔhl =f(v,g,D,μ,ρ)alsof1(Δhl…

Q: Ql:- Using the dimensional analysis, find the relationship between the variables, shear stress t,…

Q: A manometer is a device that measures pressure using a curved tube filled with liquid of constant…

Q: By using dimensional analysis concept, express the wall shear stress for the pipe flow which is…

Q: The efficiency (n) of a fan depends upon density (p), and dynamic viscosity (µ) of the fluid,…

Q: (Dimensional Analysis) If the velocity V in a fluid flow depends on a dimension 1, the fluid density…

Q: P2, 42 2h P1 Po P1, Hi L Figure 3: Two layer flow for (b) (b) Consider two immiscible (do not mix)…

A: Given: Two immiscible fluid layers,

Q: Q2: The function relates the different variables in a capillary rise of a liquid is given by: h=f…

Q: a flat plate of area 1.5×106 mm 2 is pulled with speed of 0.4 m/s relative to another plate located…

A: Given data: A=1.5×106 mm2=1.5 m2du=0.4 m/sdy=0.15 mm=0.00015 mμ=1 poise=0.1 Pa.s Need to determine…

Q: The pressure drop, AP, in a horizontal pipe depends on the pipe diameter, d, pipe length, L, pipe…

Q: Q2) Fill in the blanks with appropriate word(s), for EXKEl of the following; K Specific weight is…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: A flow from an injector is leading to the formation of a spray of liquid drops. The drops formed in…

Q: For a venturi meter given below, the volumetric flow rate is defined in terms of the geometrical…

A: Venturi Meter is a device in which pressure energy is converted into kinetic energy and it is used…

Q: P1.5 An artificial solar pond is a body of water with a density gradient created by adding salt to…

A: Given, Density variation with depth ,ρ(z)=ρo+αzWe know that,dP=ρgdzdP=(ρo+αz)gdz on…

Q: The drag force Dp acting on a spherical particle that falls very slowly through a viscous fluid is a…

Question

Q2:- If the velocity of flow v, dynamic viscosity µ, bulk modulus of elasticity K
and diameter of pipe D, using dimensional analysis, determine the general
form of relationship between these variables.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Step 1

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen, air, and saturated steam at a temperature of 100C. Let D=1m,U=1m/sec, and hc=1W/m2K.
Q1) By using dimensional analysis concept, express the wall shear stress for the pipe flow which is depending likely on the distance from the beginning of the pipe, pipe diameter, pipe wall roughness, fluid velocity, density and viscosity?
The Archimedes number, Ar, used in the flow of stratifiedfluids, is a dimensionless combination of gravity g , densitydifference Δ ρ , fluid width L , and viscosity μ . Find theform of this number if it is proportional to g .
A liquid is flowing at a volumetric flowrate of Q per unit width down a vertical surface. Obtain form dimensional analysis, the form of the relationship between Q and the film thickness. The flowrate Q is a function of density ρ, viscosity μ, film thickness δ and acceleration due to gravity g. Show that the volumetric flow rate is directly proportional to density if it is known that the flowrate is inversely proportional to the viscosity.
When disturbed, a floating buoy will bob up and down atfrequency f . Assume that this frequency varies with buoymass m , waterline diameter d , and the specific weight γ ofthe liquid. ( a ) Express this as a dimensionless function. ( b )If d and γ are constant and the buoy mass is halved, howwill the frequency change?
1 ft/min=_____ ft/h using dimensional analysis
The volume flow in a water pipe is 9000 m°/h. The pipe length is 80 m, the pipe diameter 1 m. The material data of water are a density of 1000 kg/m? and kinematic viscosity v=10® m7s. A steel pipe with roughness 0.05 mm is used. Determine the pressure drop in the pipe.
As shown in Fig. 1.12, a horizontal interface 0-0 exists between two immiscible liquids. The dynamic viscosity of these two liquids are 0.14 Pa sand 0.24 Pa s respectively. The thickness is d1 0.8 mm and d2 1.2 mm respectively. Assuming that the velocity gradient is linear. Find theforce F required to push a bottom area A 1000 cm2 wood board to movewith velocity v0 0.4 m/s along the surface?
Resistance R to the motion of a completely submerged body is given by R = ρV2 L2 φ , where ρ and ν are density and kinematic viscosity of the fluid while L is the length of the body and V is the velocity of flow. If resistance of a one-sixth scale airship model when tested in water at 10 m/s is 230 N, what will be the resistance in air of the airship at the corresponding speed? Kinematic viscosity of air is 13 times that of water and density of water is 810 times of air.
The variables in a Saybolt viscometer are the time (t) required to empty a certain volume of oil of density (ρ) and viscosity (μ), a length (L) representing the dimensions of the viscometer, and the gravitational acceleration (g). Using the Buckingham Pi-theorem, show that
The absolute viscosity μ of a fluid is primarily afunction of( a ) Density, ( b ) Temperature, ( c ) Pressure, ( d ) Velocity,( e ) Surface tension
Choose the correct answer Kinematic viscosity is * f. dynamic viscosity* Density b. About 1.2*10^-2 m2/s for water e. Both b and d c. Density*dynamic viscosity d. Both a and c g. Both f and c a. About 1.2*10^-6 m2/s for water