A11 kV,15 km length primary feeder connected to a balanced load of 950 kW at a power factor of 0.85 lagging. The impedance of a feeder is 4.5 +j7.5 ohms per km.Determine the following (a) The voltage drop and power loss of the feeder, when the load is uniformly distributed (b) The voltage drop and power loss of the feeder, when the load is nonuniformly distributed.

A11 kV,15 km length primary feeder connected to a balanced load of 950 kW at a power factor of 0.85 lagging. The impedance of a feeder is 4.5 +j7.5 ohms per km.Determine the following (a) The voltage drop and power loss of the feeder, when the load is uniformly distributed (b) The voltage drop and power loss of the feeder, when the load is nonuniformly distributed.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.44P: Two balanced three-phase loads that are connected in parallel are fed by a three-phase line having a...

See similar textbooks

Similar questions

A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads that are connected in parallel. One of the loads is Y-connected with an impedance of (30+j40) per phase, and the other is -connected with an impedance of (60j45) per phase. The line is energized at the sending end from a 60-Hz, three-phase, balanced voltage source of 1203V (rms. line-to-line). Determine (a) the current, real power. and reactive power delivered by the sending-end source: (b) the line-to-line voltage at the load: (C) the current per phase in each load: and (d) the total three-phase real and reactive powers absorbed by each load and by the line. Check that the total three- phase complex power delivered by the source equals the total three-phase power absorbed by the line and loads.
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Two balanced loads are connected to a 240-kV rms 50-Hz line. Load 1 draws 30 kW at a power factor of 0.6 lagging, while load 2 draws 45 kVAr at a power factor of 0.8 lagging. Assuming the RYB sequence, determine: (a) the complex, real, and reactive powers absorbed by the combined load, (b) the line currents, and (c) the kVAr rating of the three capacitors ∆-connected in parallel with the load that will raise the power factor to 0.9 lagging and the capacitance of each capacitor. Verify the results by creating a MATLAB Simulink model and program. Obtain the plots for the currents and voltages
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.
The annual load duration curve of a power supply system may be considered as straight line from 40 MW to 8 MW. The load factor of the system is ?
S.1) The serial impedance per phase of a three-phase 45 km energy transmission line is 2 + j4 / phase. A load with a power factor of cos2 = 0.8 forward is fed from the end of the line. Since the line voltage at the beginning and end of the line of the energy transmission line is wanted to be kept constant at 115 kV, a) Active and reactive powers drawn from the beginning and end of the line, b) Calculating the power consumed along the energy transmission line and the efficiency of the line. S.2) Line constants of an energy transmission line are given as A = D = 0.8746 + j0, B = 0 + j128.34, C = j0.0018316 S. At the beginning of the line, it is desired to write 1920 MW active power and 600 MVAr reactive power lines under 7650kV line voltage. According to this business, a) Calculate the line end magnitudes (U2, I2 and P2). b) What value does the end voltage take when the load fed from the end of the line is deactivated? S.3) The length of a phased energy transmission line with a…
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the average powers delivered to the load and absorbed by the line. The average powers delivered to the load and absorbed by the line are ________ and ____________ , respectively.
A generating station supplied the following loads: 150 MW, 120 MW, 85 MW, 60 MW, and 5 MW. The station has a maximum demand of 220 MW. The annual load factor of the station is 48%. Calculate : 1) the number of units supplied annually 2) diversity factor 3) demand factor
Two interconnected substations O and P are interconnected via a distribution line of impedance6 + ?8Ω. Assume a load of 20MVA, at 0.8 power factor lagging is delivered at a bus-bar voltageof 66kV at P from O. Determine:a. the bus-bar voltage at substation Ob. the efficiency of distributionc. the power factor angle at O
The yearly load duration curve of a certain power station can be approximated as a straight line; the maximum and minimum loads being 40 MW and 10 MW respectively. To meet this load, three turbine generator units, two rated at 20 MW each and one at 10 MW are installed. Draw the load duration curve and determine: (i) Installed capacity (ii) Plant capacity factor (iii) kWh output per year (iv) Load factor.
a) You have been employed as an electrical engineer by a power transmission company to design a short transmission line to supply power to a light-industrial load consumer with power system specification as follows, a 3-ph, 60Hz overhead short transmission line with a line-to-line voltage of 23KV at the load end, line impedance of 2.48 ±j6.57Ω/phase, the industry has a cumulative consumption of 9MW with a power factor of 0.85 of lagging as a result of several induction motor on its production lines.As part of the regulations for connections to the grid, you are to provide justifications and values to the Energy Commission of Ghana.(i) What would be value of the voltage between the live conductor and the neutral, between live and live voltages at the industrial premises of the factory?(ii) What load angle would expect the factory to be operating at?
Assuming the voltage at the utility bus is 13.5 kV and the PV plant supplies 4.8 MW of power at 0.95 power factor lagging. Draw the diagram of the system and determine i) the per-phase voltage and current at the POI at the PV plant ii) the reactive power delivered and that which is lost in the line. Assume the line is modelled as a short line.