For the lap joint shown in the figure is fastened by three 20-mm Φ rivets. Assuming that P=50 KN, determine the maximum average tensile stress in each plate. Assume that the applied load P is distributed equally among the three rivets. Activity 2: For the lap joint shown in the figure is fastened by three 20-mm O rivets.Assuming that P=50 KN, determine the maximum average tensile stress in each plate.Assume that the applied load P is distributed equally among the three rivets.(0,= 18.18 MPa)20 mm25 mm

Diameter of rivet, d= 20 mmP= 50 KNThickness of plate= 25 mm

Activity 2: For the lap joint shown in the figure is fastened by three 20-mm 0 rivets. Assuming that P=50 KN, determine the maximum average tensile stress in each plate. Assume that the applied load P is distributed equally among the three rivets. (5, = 18.18 MPa) P 20 mm 25 mm P.

Activity 2: For the lap joint shown in the figure is fastened by three 20-mm 0 rivets. Assuming that P=50 KN, determine the maximum average tensile stress in each plate. Assume that the applied load P is distributed equally among the three rivets. (5, = 18.18 MPa) P 20 mm 25 mm P.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 8.6P: Two line loads q1 and q2 of infinite lengths are acting on top of an elastic medium, as shown in...

See similar textbooks

Related questions

Q: 1) In the system given in the adjacent figure, the normal stress that will occur in the a-a section…

A: Normal stress = δn ≤ 150MPaShear stress = T = 60MPaCross section of BC = xy = 53mm

Q: figure. The shear stress varies linearly with the height z. To is the shear stress at the top of the…

Q: The force p is applied at d=50 mm from the bottom as shown in the figure. Compute the normal stress…

A: Find equivalent force and moment at the section a-a. Then using stress equation the state of stress…

Q: P2 Consider a point in a structural member that is subjected to plane stress. Normal and shear…

A: Given data : Normal stress in X direction (σX)=-36 ksiNormal stress in Y direction (σY)=-18 ksiShear…

Q: Problem 4 The horizontal force of p 85 kN acts at the end of the plate. The plate has a thickness of…

Q: For the beam shown in the figure, find the shear stress in MPA at a point 30 mm above the bottom of…

A: Given:- A beam is given with a point load The magnitude of the point load = 14 kN To determine:-…

Q: Problem #1. The figure below are 2 solid cylindrical bars joined together at point B. Find the…

Q: The force p is applied at d=50 mm from the bottom as shown in the figure. Compute the normal stress…

Q: horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: a) Find the displacements at point C of the frame using Finite Element Method. b) Draw the stress…

Q: The grain of the wooden member forms an angle 15° with the vertical. For the state shown in Figure…

A: Mohr's circle Mohr's circle is a graphical depiction of a point's overall condition of stress. It is…

Q: PROBLEM 01: The rigid bar BD in Figure pivots about support C. Due to the application of force P,…

Q: 90 MPa 1. If a point is subjected to the state of stress shown in the figure, determine the…

Q: Problem 2 If P= 8.571 kN, Determine the stress in member CE assuming that the area in steel is 24…

Q: 12 МPа 6 MPa 8 MPa

Q: d1=60 mm and d2 =36 mm .Determine stress in rod in AB and BC

A: Given data : Diameter for rod AB (d1)=60 mmDiamter for rod BC (d2)=36 mmTo find about :Stress in…

Q: Part2: Using Mohr's circle, draw the circle and determine: a) The principal stresses at point B and…

A: It is required to determine the principle stresses.

Q: Q.6 A beam has solid circular cross-section having diameter d. If a section of the beam is subjected…

Q: 4. The normal stress on plane pq of a prismatic bar in tension (see figure) is found to be 7500 psi.…

Q: 8 ksi 2. For the state of stress shown in the figure, determine normal and shearing stresses on the…

Q: 2. Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is applied to the…

A: Draw free body diagram From the above figure, calculate the angle α sinα=35α=sin-10.6α=53.13o

Q: Determine the normal stress in each segment of the stepped bar shown in Figure 4. Load P 20 kN %3D

A: Given data : Load (P)=20 KNForce in AB (FAB)=P=20 KN (Tensile)Force in BC (FBC)=-P+6P=5P=5×20=100…

Q: 1.W.1/The cantilever beam in Figure below has a rectangular cross section with dimension 20…

Q: A thin strap is wrapped around a solid rod as shown in Figure 1a. Determine the principal stresses…

Q: Draw Mohr's circle and find: 1) Principle stresses and their direction. 2) Maximum Shear stress and…

Q: The overhanging beam ABC in Figure supports a concentrated load and a uniformly distributed load.…

A: Point load of 20 kN UDL of 12kN/m for 10m Applying equilibrium conditions ΣV =0…

Q: 1. (Problem 7.3 from the text book) For the given state of stress, determine the normal and shearing…

A: step 1-

Q: 1. The cross-sectional area of bar ABCD is "X" mm². Determine the maximum normal stress in the bar.…

A: The formula to calculate the normal stress is given by, σ=PA ...1 Draw the…

Q: Problem 2 6 kip -3 in. 12 kip Determine the normal stress developed at point A and B. Neglect the…

A: A calculating moment about x and y-axis:

Q: his state of stress. (b) Determine the principal stresses (σp1>σp2) and the maximum in-plane shear…

A: σx=17ksiσy=-11ksiτxy=-17ksiRadius of the…

Q: 2. For the following stress function o to be a valid Airy stress function, what should be the…

Q: H.W.3: Two solid cylindrical rods support a load of P 27 kN, as shown in Figure 1 .Rod (1) has a…

A: given data: P=27 KN D1=16 mmD2=12 mm

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: A solid circular pole is subjected to linearly varying distributed force with maximum intensity qo…

A: Normal stress at the base 150MPa qo=6.9kN/m L=6m P=80kN

Q: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is…

A: Draw the free body diagram. Equilibrium of horizontal forces, ∑Fx=0F1-34-34+18+18-25=0F1=57 kips…

Q: 2.11 The stress function = Ax + Bxy + Cy provides the direct and shear stresses in a thin…

A: The given stress function is,ϕ=Ax2+Bxy+Cy2A,b are,u=2aC-vAEv=2BA-vCE

Q: From the figure below, a shaft consists of different sections. Bar (a) is a hollow bar and has an…

Q: z/2 r/2

Q: Calculate for the Moment in kN-m at member KH in kN-m at joint K of the frame shown in figure 1…

A: Given data:

Q: 1. A platform supporting a load hangs from point B. Ignore weights of the rod AB, the strut BC, and…

Q: A force of 521 kN is applied at joint B to a system of two-pinned joined bars shown in the figure.…

A: Determine the required cross-sectional area of the bar BC

Q: 2) The cross-sectional dimensions of a beam are shown in Figure 2. a) Determine the centroid…

A: Given Data -

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

A: Find the equivalent force couple system at the section a-a. Then using stress equation the normal…

Q: For the bar subjected to the uniform line load in the axial direction shown in Figure P3-55,…

Q: Q1) A stat of stress is specified in Figure. By using Mohr's circle determine the normal and…

Q: A beam has a rectangular cross section and is subjected to the stress distribution shown here.…

A: (a) By flexure formula:MI=σymax⇒M = σIyMax = 2 x 103x 1 x6 x (12)36 x 12M = 2 x 103 x144M = 288…

Q: 01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

For the lap joint shown in the figure is fastened by three 20-mm Φ rivets. Assuming that P=50 KN, determine the maximum average tensile stress in each plate. Assume that the applied load P is distributed equally among the three rivets.

Activity 2: For the lap joint shown in the figure is fastened by three 20-mm O rivets.
Assuming that P=50 KN, determine the maximum average tensile stress in each plate.
Assume that the applied load P is distributed equally among the three rivets.
(0,= 18.18 MPa)
20 mm
25 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2 Calculate maximum average tensile stress in each plate

VIEW

Step 3 Calculate shear stress

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 450 mm2. Determine the average axial stress in each bar. q = 5 t = 0
d1=60 mm and d2 =36 mm .Determine stress in rod in AB and BC
Determine the stress components (σx′ , τx′y′) acting on the inclined plane AB in (Figure 1), where τxy=−38.5MPa. Solve the problem using the method of equilibrium.
The pulley shown is connected to a bracket with a circular pin of diameter d = 4.5 mm. Each vertical side of the bracket has a width of b = 26 mm and a thickness of t = 2.2 mm. Consider a free body diagram of the pulley with the belt tensions. Solve for the reaction forces Rx and Ry. If the pulley belt tension is P = 660 N, what is the average bearing stress produced in the bracket by the pin?
Find the maximum torsional stress in shaft AC shown in the following figure. Assume the shaft from A to C is 10 mm diameter
The column in the figure is under the effect of a load of P = 16 kN. Find the stress at point A according to the given?
The internal shear force at a certain section of a steel beam is V = 8.1 kN. The beam cross-section shown in the figure has dimensions of b=137 mm, c=33 mm, d=66 mm, and t=7 mm. Determine: the shear stress at point H. [Answer: 7.43 MPa]
The solid circular section EF rod in the figure is fixed to the wall at point F. Forces P1 = 1 kN, P2 = 2 kN were applied from point D of the DE rod, which is rigidly connected to the rod. Calculate the stress states occurring at points A and B and show them on the small volume elements removed from these points. The diameter of the EF rod will be taken as d = 50 mm. Do not give answer in image and hand writing
if the beam is subjected to a bending moment of m = 10 kN•m, determine the bending stress in the beam at points a and b, and sketch the results on a differential element at each of these points.
S1) The figure shows the stress distribution in the rectangular cross section of a beam.According to this;(a) Write the expression for stress ?x, taking into account the directions of Fx, My and Mz.(b) Show that My is zero for symmetrical normal stress distribution.(c) Using the stress function ?x, find the axial force Fx acting on the rectangular cross sectionin width b and height h.(d) Obtain the equation of Mz bending moment.Hint: In this question, using the stress distribution in the figure, it is aimed to determine thecross-sectional effects of Fx, My ve Mz causing this stress distribution
A moment is exerted on the profile given in the figure to make an angle B with the vertical. Calculate the stress at point B. Given a = 90 mm, b = 60 mm, c = 110 mm, d = 130 mm, Beta = 80 degrees, M = 13 kNm,
The supported beam in the figure has its cross section and area shown. Determine the Absolute Maximum Bending Stress, draw the stress distribution over the cross section at this location. Also, what is the stress at point C of the cross section?