Activity 2: Ohm's Law & Kirchhoff's Law in Mixed Circuits Examine the circuit carefully and calculate the missing values using Ohm's Law and Kirchhoff's Law. Show all of your work on a separate piece of paper and record your final answers on this page. Keep two decimal places.

Activity 2: Ohm's Law & Kirchhoff's Law in Mixed Circuits Examine the circuit carefully and calculate the missing values using Ohm's Law and Kirchhoff's Law. Show all of your work on a separate piece of paper and record your final answers on this page. Keep two decimal places.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Reclung.c A on ri gle Figure 1 2. The circuit shown above is constructed with two 6.0 V batteries and three resistors with the values shown. The currents 1₁, 12, and 13 in each branch of the circuit are indicated. 2 GEOMETRY AND TRIGONOMETRY Circle A = ²² C = 2πr Cy.inder bh - re Rectangular Solid Vlh Sphere 1. Using Kirchhoff's rules, write, but DO NOT SOLVE, equations that can be used to solve for the current in each resistor. ii. Calculate the current in the 200 9 resistor. iii. Calculate the power dissipated by the 200 2 resistor. V = ar²l S.. Figure 2 The two 6.0 V batteries are replaced with a battery with voltage & and a resistor of resistance 50 2, as shown above. The voltmeter V shows that the voltage across the 200 £2 resistor is 4.4 V. (b) Calculate the current through the 50 2 resistor. (c) Calculate the voltage & of the battery. V=² S = 4; 7² Rig Triangle 2 +6² = c² sin = COS== tan 8 = OJA b C 2m. a b 6.0 V 7,4 & A - area C=circumference h-hei £= le L W = IUL r=fuu.0…
What to do: Answer the following problems. Write your solutions in a separate sheet of paper. 1. Compute the equivalent resistance of the network in the circuit shown below. Show the steps in reducing a combination of resistors to a single equivalent resistor. The source of emf has an negligible internal resistance. E = 18 V, r = 0
Activity 2 Directions: Solve for the given problems. Show your complete solutions. Express your final answers into 3 significant figures. 1. Silver is composed of 5.8 x 1028 free electrons per cubic meter. If a silver wire with a diameter of 1.8 mm can allow charges of 360 C to flow in 1 hour, a. What is the current in the conducting wire? b. What is the magnitude of the drift velocity of the electrons in the conducting wire? 2. A wire has a radius of 1.90 mm. If the current in the wire is 6.14 A, the drift velocity is 4.86 x 10-5 m/s. What is the concentration of free electrons in the metal?
1. For all practical purposes, a capacitor is considered fully discharged (or fully charged) after 5 time constants. What is the voltage across a discharging capacitor in a RC circuit that has V₁ = 10V, and t = 5 t seconds? Show your work 2. What is the purpose of finding t in a RC circuit? 3. In the virtual simulation, the light bulb is a nice visual indicator of the behavior of a discharging series RC circuit. However, explain why is it easier to find C using a resistor instead of a Light Bulb.
Directions: Solve the given problems. Show your complete solutions.Round off your answers into the proper number of significant figures.1. A silver wire 2.5 mm in diameter transfers a charge of 370 C in 70 minutes.Silver is made up of 5.8 x 1028 free electrons per cubic meter.a. Find the current in the wire.b. What is the magnitude of the drift velocity of the electrons in the wire?
Part a: what is the equivalent capacitance of the circuit shown above? Give your answer in microfarads. part b: what is the charge on the 4.0 mu*F capacity? Give your answer in microcoulombs par t c:What is the voltage on the 4mu*F capacitor ? Give your answer in Volts part c What is the voltage on the 2.0uF capacitor? Give your answer in Volts part d :
Problem #5 Vi = 10V a R1-2ohms R4 = 5ohms ww R3 = 7ohms ww R2 = 3ohms R560hms. ww Figure P5 Wheatstone Bridge Circuit a. Solve for Vth between points a and b where RL = R3, using Thevenin's theorem b. Solve for the votlage drop across R3 b
1.Find the current (I1) from the following diagram. R=2000 R=25000 R= 6000 Q E=12 V Current (1) = mA %3D 2.The batteries in each of the circuits shoOwn below are same and the wires have negligible resistance. Which circuit from the following dissipates the very less power? TAX ohms 2ohms 2 ohms E)
Solve for the given problems. Show your complete solutions. Round off your answers into 3 significant figures Refer to figure 7. a. Find the current in the circuit. b. Find the terminal voltage Vab of the 16.0-V battery. c. Compute for the potential difference Vac.
50 Ω ww mit this before the beginning of the lab period. Show all work. 1. In the circuit to the right, label the currents in each branch. Then write three equations using Kirchhoff's rules that can be used to find the currents through each branch. Solve for the current through each resistor and each battery. 115 Ω 35 V Hil 95V 80V 6052 www 350 2. If you have a maximum voltage of 9.6V, determine what resistance should be used in order to get a current of no more than 200 mA. Is this a maximum or minimum resistance?
In the diagram above, each \(| |\) represents a communication cable. We know that cable failures may be considered independent events, and you can assume that, at any time, the probability that any cable is working correctly is 0.4. Correct your answers to 4 decimal places. Find the chance that exactly two cables are operating correctly at a given time.Answer Find the chance that cable g and exactly one other cable are operating correctly at a given time.Answer Find the chance that A can communicate with B, if we know that exactly six cables are not operating correctly at a given time.Answer
You have been asked to do the following tasks to reflect your understanding to D.C circuit’s theorems. You must provide all analysis and show your steps to solve the problems. A) Show detailed calculation steps with graphics to find Req for the circuit shown in Fig.1.(Note: R3=R5= the last two digits of your ID number (kilo-ohm))