QUESTION FOURKindly answer correctly. Please sho all the necessary steps Actual air fuel ratioasair fuel ratioHic=actual air fuel ratio14.57 <22.97 (32 + 3.7 x 28)1.875 (8×12 +18)14.57is less14.86Therefore, mixture Strength isthan"rich".Statiometric

The optimal air to fuel ratio for a gasoline engine is known as the stoichiometric mixture, which…

Answered: Actual air fuel ratio= HU 22.97 (32…

Engineering

Mechanical Engineering

Actual air fuel ratio= HU 22.97 (32 +3.7 x 28) 1.875 (8x12 +18) 14.57

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The rectangular plate has a semi-circle cut out as shown. The x' and y' axes go through the centroid…

Q: 2m 1.5 m 0.5 m 0.5 m 56m y A a.) A 1.5 m length of 30mm diameter solid steel bar fixed at one end is…

A: Given: The length of solid steel bar, L = 1.5 m The diameter of solid steel bar, d = 30 mm = 0.03 m…

Q: Force Pressure Area Area Pi Radius Radius Standard Units: Force is in Newtons (N), Pressure is in…

Q: The section modulus is 2610.759 in3. The most economical metric wide-flange shape is [W12 x 96

Q: Gate 6-ft wide M 459 Water 4 ft 2 ft 1 ft So=6

Q: 1.56) The vertical post is secured by three cables. The cables are pre-tensioned so that the…

Q: At the instant shown, wheel A rotates with an angular velocity of w = 12 rad/s and an angular…

A: Given data: ω=12 rad/secα=12 rad/sec

Q: Describe the pressure generation- hydraulic pump for aircraft that’s using the electrical,…

A: The hydraulic system of aircraft is complex one that provides help for the operation of an aircraft…

Q: No wrong answer please , i could downvote The piece of suture is tested for its stress relaxation…

Q: 25° ℗. R IF Block (choice A) Block (choice C) 25° a Ф. Block (choice B) 25 Block (choice D) Φ

Q: A rectangular bar of dimensions bx h mm is subjected to a combined bending load as shown. For b-12…

A: Given data: Width of bar (b)=12 mm Height of bar (h)=25 mm Moment in y- direction (My)=104 Nm Moment…

Q: Consider a diesel electric plant which consumes a thousand liters of fuel with 20 oAPI at 200K in a…

A: GivenV=1000ltr= 10001000m3=1m3APIo=20otime =1day=24×60=1440 min

Q: If the density of the gas is 0.003 slugs per cubic foot, what is the specific weight of the gas O…

A: Given data: Density = 1 slugs per cubic ft Need to determine the specific weight of the gas.

Q: O₂A = 100 mm AB= 120 mm LX (2) 002-20 rad/s a₂ = 0 90° 90⁰ (03 α3 Vp = Vo+V+wXR Ap = Ao + A…

A: Given: The angular speed of link 2, w2 = 20 rad/s The angular acceleration of 2 = 0 rad/s^2 The…

Q: 7.34 Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

Q: The 24T 6-pitch 20° pinion 2 shown in the figure rotates clockwise at 900 rev/min and is driven at a…

A: Given Data: Speed of the 24T 6-pitch 200 pinion 2 is 900 rev/min clockwise. Power at which pinion…

Q: Calculate the horizontal force P on the light 10° wedge necessary to initiate movement of the 34-kg…

Q: can you write it in a paper? i dont know if its aA2 or aA2 or what

Q: Determine the Moment of Inertia about the X axis, Moment of Inertia about the Y axis and the Product…

A: Concept: The product of inertia can be determined by the following equation. Here, Ix'y' is the…

Q: A 10 cm diameter cylindrical bar, heated in furnace to a uniform temperature of 2000 C, is allowed…

A: given; diameter(d)=10cm =0.1m temperature of surroundings(T1)=2000cenviornment…

Q: A block 4, of mass m is connected through a cable and a pulley to an elastic spring (see figure…

A: Given data: k=100 N/mθ=45°m=85 kg Need to determine the distance covered by the block when it stops…

Q: Consider the beam shown in (Elgure 1). Suppose that a 100 mm, b=230 mm, c-20 mm. Figure 1 of 1 Part…

Q: Determine the force required to produce stress of 2 N/mm2 if cross sectional area is 2 mm2

A: Given data: ◆ The stress developed in the area: σ = 2 N/mm2 ◆ The cross-sectional area: A = 2 mm2…

Q: please solve the centroidal Ix, centroidal Iy, Ix and Iy of the attached figures. Underline/box…

A: Given Shaded zone To find Moment of inertia

Q: wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m.…

Q: What is the mass density of a liquid whose specific gravity weight is 9000N/m³? 917.4 kg/m^3…

Q: A single-sided centrifugal compressor is rotating at a rotational speed N of 290 rev per second.…

Q: which represents direction of @point 2. वि 23/ ? , Pu lincar acceleration

A: Linear acceleration is in the direction of D1.

Q: A diesel power plant supplies energy for a certain Cooperative. During a 24-hr period, the plant…

A: Given data: during 24 hr period the plant consums 200 dallons pof fuel at 301k and produced…

Q: Q3 please

A: (a) Draw a sketch of blender and show the energy transfer across the system boundary.

Q: 5/117 The system of Prob. 5/88 is repeated here. At the instant under consideration, the rod of the…

A: Given: The speed of A, VA = 2 m/s

Q: A person holds horizontally a 20 Kg bar with both hands (see Figure 2.1). The hands are 1.5 m apart…

Q: 3. A part is oriented and immobilized relative to the three mutually perpendicular intersecting…

A: Ans: option first is correct. Precedence

Q: 1 -Using the Energy method, derive the equation of motion Assume that the rotation is very small. 2…

Q: How do the different zones of gas turbine combustor affect the formation of pollutants?

A: To find: The generation of pollutants is influenced by the various zones in gas turbine combustor.

Q: can someone explain why P is a function if time only for this question

Q: and the equations: Әр дz - ар дх ӘР ду 0 <=0 (2) +μ0²oz = 0 (3) Are a solution of incompressible…

Q: Water has its viscosity at 68 degrees F equal to 0.1008 poise, what is its absolute viscosity in…

A: Given Data, Viscosity at 0.1008 poise We have to find absolute Viscocity in pound second per square…

Q: 4. The flatness tolerance zone does not need to be O parallel to any other surface specified in the…

A: Tolerance can be defined as the total amount of the dimensions of a part which can vary and is the…

Q: Calculate the indicated power of a cylinder and the engine, if the mechanical efficiency of the…

A: Given: The diameter of the cylinder: →D=500 mm=0.5 m Length of the piston stroke: →L=2050 mm=2.05 m…

Q: Oil in a tank has a specific gravity of 0.82. Determine the gage pressure at 3.75 m below the liquid…

Q: Consider water transfer between two larger storage tanks. Lower tank water surface 10 m lower than…

A: Given data: Discharge (Q)=1m3s One storage tank is 10 m higher than the other. Let Z1 is the…

Q: . A major water main is an 18 in ductile iron pipe. Compute the Reynolds Number if the pipe carries…

A: Given: Let us consider the given data, Diameter,D=18 in Flow rate, Q=16.5 ft3s Water…

Q: A particle is traveling along the parabolic path y = 0.25x² . If x = (2t² ) m, where t is in…

Q: The slender 15-kg bar is initially at rest and standing in the vertical position when the bottom end…

A: a=6m To find speed at which end A strikes D

Q: The solution is incomplete

A: Given data: Time taken to reach 27 km/h from rest = 4 s Resistances = 4% of the vehicle mass Mass…

Q: When selecting datum features, the designer should consider features that are:

A: Given Datum features To find Designer consideration for datum

Q: The pavement compactor is traveling down the incline at VG = 5 ft/s when the motor is disengaged.…

A: Given data: vG=5 ft/sWBody=WA=800 lbkA=3.3 ftkB=1.8 ftWfront=800 lbd=16 ft Need to determine the…

Q: Prob3 Consider a laminar flow that flow rate Q=0.2 ft³/s; v = 6.55 * 10.5 ft²/s. Find pipe diameter…

A: Reynold number for the fluid flowing through the pipe: When the flow occurs in a pipe, the flow is…

Q: Two plates are separately by a H = 1/4 in. space. The lower plate is stationary; the upper plate…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

QUESTION FOUR

Kindly answer correctly. Please sho all the necessary steps

Actual air fuel ratio
as
air fuel ratio
H
ic
=
actual air fuel ratio
14.57 <
22.97 (32 + 3.7 x 28)
1.875 (8×12 +18)
14.57
is less
14.86
Therefore, mixture Strength is
than
"rich".
Statiometric

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Explanation

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The exhaust gas analysis of an engine using octane as fuel gives equal volumes of CO, and unused O, Computer actual and stoichiometric air-fuel ratio. For equivalence ratio of 1. Calculate The volume of mixture per kg of fuel at pressure of 100 kPa and temp 70°C., (i) The volume of combustion products per kg of fuel when femp. of products is127°C at 1 bar.
I will give a thumbs up. Please help me 30 mins. left Given the ultimate/gravimetric analysis of coal as follows: C=81.95%, H2 = 4.63%, S=0.96%, N2=1.3%, O2=5.75%, Ash=6.09%, Moisture = 3.05% Using ash and moisture free analysis. Determine the; theoretical air fuel ratio:
Please help me (1 hour left), I will give a thumbs up Given the ultimate/gravimetric analysis of coal as follows: C=81.95%, H2 = 4.63%, S=0.96%, N2=1.3%, O2=5.75%, Ash=6.09%, Moisture = 3.05% Using ash and moisture free analysis. Determine the; theoretical air fuel ratio at 30% excess:
(Calculation of average velocities) A gas mixture ( N_{2} =5% H_{2} =15% . NH_{3} =76% and Ar = 4% ) flows through a pipe, 25.4 mm in diameter, at 4.05 bar total pressure. If the velocities of the respective components are 0.03 m/s, 0.035 m/s, 0.03 m/s and 0.02 m/s, calculate the mass average, molar average and volume average velocities of the mixture.
When are mixtures termed as fuel rich in internal combustion engine?
Prob. # 3] A producer gas has the following percentage volumetric composition: CO2 = 10.8 %,CO = 18.3 %, CH4 = 3.10 %, O2 = 0.10 %, H2 = 12.9 %, N2 = 54.6 %, and C2H4 = 0.20.Calculate: a) the weight analysis by elements; b) the weight analysis by compound; and c) theair-fuel ratio for an excess air of 35 %.
please solve breifly In an engine test the dry volumetric analysis of the products was CO2 0.0527, O2 0.1338 and N2 0.8135. Assume the fuel is a pure hydrocarbon and that it is completely burnt. Write the complete balance chemical equation on volume basis. Estimate: The ratio of carbon to hydrogen in the fuel by mass. The air/fuel ratio by Assume the percentage of nitrogen in air is: 76.7% by mass and 79% by volume (or mole). Please : Do not solve this problem in tabulated form, otherwise your answer will be considered totally wrong.
A gaseous fuel mixture has a molal analysis:H2 = 14% CH4 = 3% CO = 27%O2 = 0.6% CO2 = 4.5% N2 = 50.9%Determine the theoretical air-fuel ratio for complete combustion on molal analysis.
2.In an engine test the dry volumetric analysis of the products was CO2 0.0527, O2 0.1338 and N20.8135. Assume the fuel is a pure hydrocarbon and that it is completely burnt.(a) Write the complete balance chemical equation on volume basis.Estimate:(b) The ratio of carbon to hydrogen in the fuel by mass.(c) The air/fuel ratio by mass.Assume the percentage of nitrogen in air is: 76.7% by mass and 79% by volume (or mole). NOTE: Do not solve this problem in tabulated form, otherwise your answer will be considered totally wrong.
Given the ultimate/gravimetric analysis of coal as follows: C=81.95%, H2 = 4.63%, S=0.96%, N2=1.3%, O2=5.75%, Ash=6.09%, Moisture = 3.05% Using ash and moisture free analysis. Determine the; theoretical oxygen fuel ratio:
In an engine test the dry volumetric analysis of the products was CO2 0.0527, O2 0.1338 and N2 0.8135. Assume the fuel is a pure hydrocarbon and that it is completely burnt. Write the complete balance chemical equation on volume basis. Estimate: The ratio of carbon to hydrogen in the fuel by mass. The air/fuel ratio by Assume the percentage of nitrogen in air is: 76.7% by mass and 79% by volume (or mole).
Calculate the equation of complete combustion of C9H20 fuel and the air/fuel ratio., C=12 kg/kmol, H2=2 kg/kmol, N2=28 kg/kmol, O2=32 kg/kmol