Additional dimensional detail for a front-end loader is shown in the figure below. The weight of the bucket and its load is 5000 lb with the center of gravity at G. Ignore the effects of the weights of the other members. Determine the force in the hydraulic cylinder CE. 2"- 3" 12" E 12" D 5" F 15" 16"-

Additional dimensional detail for a front-end loader is shown in the figure below. The weight of the bucket and its load is 5000 lb with the center of gravity at G. Ignore the effects of the weights of the other members. Determine the force in the hydraulic cylinder CE. 2"- 3" 12" E 12" D 5" F 15" 16"-

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.97P: The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces...

See similar textbooks

Similar questions

The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces are applied to the handgrips. (Hint: The horizontal components of pin forces at B and D are zero due to symmetry.)
The linkage is made of two homogenous bars of weights shown in the figure. Determine the horizontal force P required to hold the linkage in the position shown.
The center of gravity of the nonhomogeneous bar AB is located at G. Find the angle at which the bar will be in equilibrium if it is free to slide on the frictionless cylindrical surface.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
Determine the horizontal and vertical component of force which the pin at C exerts on member BC of the frame in fig 6-28a. finish with the metode of problem solution, Thanks
Question 3) The position of the head and neck and the forces acting on the head are shown in the figure. The center of gravity of the head of mass m=8 kg is located at point C. Neck muscle strength of FM=130 N, which makes an angle of γ=65° with the vertical from the B point to the skull, is affected by the neck extensor muscles. The center of the atlantooccipital joint is located at point B. For this flexion position of the head, the FJ joint reaction force, which makes an α angle with the horizontal from point A, acts. (Take the gravitational acceleration g as 9.81 m/s2). Accordingly; a) Calculate the angle α of the FJ joint reaction force with the horizontal. Response b) Calculate the FJ joint reaction force. (Write your result in N.) Answer
The boom in the figure supports a load W = 1400 lb. Compute the forces in the cables AE and BD and also the components exerted by the ball and socket joint C.
The uniform bar AB weighing 240 lb. is mounted as shown in Figure upon a carriage weighing 480 lb. The center of gravity of the carriage is at C midway between the wheels. If P = 180 lb. and there is no frictional resistance at the wheels, find R1 and R2, and also the horizontal and vertical components of the pin pressure at A.
The cord shown in the figure is wrapped around a frictionless pulley and supports a block with a mass of 100 kg. (A) Clearly show the needed free-body diagram. (B) Calculation for determining of the horizontal support reaction at the pin support at A, using the FBD of entire frame. (C) Calculation for the determination of the pin reaction at C, using the free-body diagram of pulley at C. (D) Calculation for the determination of the vertical reaction of the pin support at A, using the free body diagram of member ABC. (E) Calculation for the determination horizontal and vertical reactions of the pin support at B, using the free body diagram of member ABC.
As per the crane shown in the Figure. Determine the force member at BD.
The image depicts the components of a floor jack. If the hydraulic cylinder AB is intended to withstand a maximum compressive force of 37 kN, find the load L (in kN) and force (in kN) in link EF under this circumstance. Additionally, compute the pin reaction (in kN) at C. The hydraulic cylinder AB, the link EF, and the platform DF all have the necessary FBDs. Additionally, create a combined FBD for the platform DF and the member BCD. Take note that if the figure CDFE is traced, it becomes a parallelogram. Additionally, members BCD and EF are connected to the jack's base via pins at C and E. Disregard the friction between members BCD and EF's contacting faces.
The cord shown in the figure is wrapped around a frictionless pulley and supports a block with a mass of 100 kg. Calculation for the determination of the vertical reaction of the pin support at A, using the free body diagram of member ABC. Calculation for the determination horizontal and vertical reactions of the pin support at B, using the free body diagram of member ABC.