After determining the absorbance of several standards of known concentration, the trendline for a calibration curve (AKA a standard curve) plotting absorbance (y-axis) against concentration (M, x-axis) is determined to be y = 4.586x + -0.0010 The absorbance of a solution of unknown concentration is determined to be 0.68. Calculate the concentration of the unknown solution in M. Give your answer to three decimal places.

After determining the absorbance of several standards of known concentration, the trendline for a calibration curve (AKA a standard curve) plotting absorbance (y-axis) against concentration (M, x-axis) is determined to be y = 4.586x + -0.0010 The absorbance of a solution of unknown concentration is determined to be 0.68. Calculate the concentration of the unknown solution in M. Give your answer to three decimal places.

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter27: Molecular Fluorescence Spectroscopy

Section: Chapter Questions

Problem 27.13QAP

See similar textbooks

Similar questions

Ben ran through the experiment and found the best-fit line listed below for his standard calibration curve of absorbance vs concentration in M. y = 3214.0x + 0.0076 Ben then prepared a solution that had 5.00 mL 0.002 M iron(III) nitrate in 1 M nitric acid, 3.00 mL 0.002 M potassium thiocyanate, and 2.00 mL DI water. If the absorbance for the solution was 0.436, calculate the equilibrium concentration of iron(III) thiocyanate in the solution. Report your answer in mM with three places after the decimal.
The standard curve was made by spectrophotographic analysis of equilibrated iron(III) thiocyanate solutions of known concentration. You are asked to analyze a Fe(SCN)2+Fe(SCN)2+ solution with an unknown concentration and an absorbance value of 0.4150.415 . The slope-intercept form of the equation of the line is ?=4558.4?+0.0147y=4558.4⁢x+0.0147 . The unknown was analyzed on the same instrument as the standard curve solutions at the same temperature. What is the Fe3+Fe3+ concentration of the unknown solution?
The trendline for a calibration curve is y=4.299x+-0.0001. The absorbance of a solution of the unknown concentration is 0.0812 What is the concentration of the unknown solution in uM
Preparing a standard curve. 1. determine the absorbance max of [FeSCN]2+ it is 448.1 2. determine the concentration of FeSCN2+ in the stock solution. M1V1=M2V2 stock solution: ~0.200 M iron (iii) nitrate in 1M nitric acid intial volume: 0.3mL final volume: 10.3mL volume: 10mL ~0.002M potassium thiocyanate initial volume: 0.3mL final volume: 10.3mL volume: 10mL not sure if this is needed stock solutions: ~0.200M iron (iii) nitrate in 1M nitric acid: 0.207M ~0.002M iron (iii) nitrate in 1M nitric acid: 0.00209M ~0.002M potassium thiocyanate: 0.00193M
How do I find Concentration? flask Calculate solution Concentration (M) Volume stock of 0.40 M CuSO4 (ml) Volume of flask (ml) Absorbance at 635 nm(a.u.) 1 2.0 10 .185 2 4.0 10 .362 3 6.0 10 .510 4 8.0 10 .674 5 10.0 10 .843
A 131.7 mg sample of powdered Carbamazepine tablets was boiled with ethanol, filtered and then made up to 100 mL with ethanol. 5 mL of this solution was then diluted to 250 mL with ethanol and the absorbance at 285 nm found to be 0.486 in a 1cm path length cell.Calculate the content (% m/m) of Carbamazepine in the powder, taking A(1%, 1 cm) as 490.(State your answer to 1 decimal place and include the units)
The nickel level in a soil sample was determined using AAS. A 3.0 g sample was dissolved in acid and then diluted to a total volume of 100.0 mL. The absorbance of this solution determined at a wavelength of 232 nm, was found to be0.3. Several standard solutions were tested under the same conditions and a calibration curve shown below was obtained. Calculate the mass of nickel in mg.
The absorbance value for the Standard was 0.625 and [FeSCN^ 2+ ] std is 2.00E 4M Calculate the [FeSCN^ 2+ ] in the equilibrium mixture, report the answer to the correct significant figures. The absorbance of the equilibrium solution was 0.451
Sally obtains a standard calibration curve for their assigned food dye by plotting absorbance versus concentration (in M) of known solutions and finds the following slope and intercept: y = 1.646x + 0.026 Sally finds that her original Kool-aid sample is too concentrated, so they dilute it by transferring 13.00 mL of the original Kool-aid sample into a new container and diluting to a total volume of 37.00 mL. If the absorbance of the dilute Kool-aid sample at the appropriate wavelength for their assigned dye is 0.950, determine the concentration (in M) of the assigned food dye in the original Kool-aid sample. Report answer with three places after the decimal.
Absorbance measurements were taken on a series of Fe standards complexed with 1,10-phenanthroline. A plot of absorbance vs. concentration yielded a linear curve with the equation y=1.008e03x + 0.0395 (where y is the absorbance and x represents the Fe concentration in moles/L). Using this information calculate the Fe concentration (in ppm) in a 40.0-mL aliquot of ground water that produced an absorbance of 0.580.
A student prepared four standard solutions of (NH4)2Fe(SO4)2 and measured their absorbance at 505 nm. She created a calibration plot with the best-fit line of y = 9372 x + 0.0539. She measured the absorbance of her diluted unknown sample solution as (4.69x10^-1) nm. If she prepared her diluted sample solution by diluting 10.00 mL of the original solution to a total volume of 50.00 mL with deionized water, what is the concentration of Fe2+ in her original solution? Answer in units of M. Note: Your answer is assumed to be reduced to the highest power possible.
The nitrate in water was analyzed using a spectrophotometric method. The absorbances of the standards and the unknown sample were obtained at 550 nm.Solution Absorbance 2.00 µM 0.0656.00 µM 0.20510.00 µM 0.33814.00 µM 0.47418.00 µM 0.598Unknown 0.402 Write the equation of the lineWhat is the standard deviation of the calibration curve?