Air enters a nozzle that has an inlet area of 0.4 m?, at 200 kPa, 500 °C. and 30 m/s. At the exit the conditions are 100 kPa and 443 °C.Part AIf the exit area is 45 cm? , determine the steady-state exit velocity. Use the IG flow-state TESTcalc.Express the steady-state exit velocity in meters per second to four significant figures.ΑΣφvec?V. =m/sSubmitRequest Answer

Answered: Image /qna-images/answer/c8b69485-6d77-4903-91f6-b429d7b7cb7b.jpg

Answered: Air enters a nozzle that has an inlet…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air enters a nozzle at 2.21 ??/?^3and 30m/s. How much mass is entering the system if the orifice is 80??^2?. please use 2 decimal places for your solution
Solve for the ratio of the initial to final speed of sound if an air expands isentropically from 2.65 MPa at 75.34°C to 0.3MPa. Express your answer in 3 decimal places.
In air-conditioning applications, the temperature of air is measured by inserting a probe into the flow stream. Thus, the probe actually measures the stagnation temperature. Does this cause any significant error?
Solve for the ratio of the initial to final speed of sound if an air expands isentropically from 178.04 psia at 207°F to 65psia. Express your answer in 3 decimal places.
Air fl ows adiabatically in a 3-cm-diameter duct, withf 5 0.018. At the entrance, T1 = 323 K, p1 =200 kPa, andV1 = 72 m/s. (a) What is the mass fl ow? (b) For what tubelength will the fl ow choke? (c) If the tube length is increasedto 112 m, with the same inlet pressure and temperature,what will be the new mass fl ow?
The converging-diverging nozzle of the engine of a new supersonic unmanned aerial vehicle (UAV) has an exit area of 50 cm^2 . At the design operating condition, the mass flow rate of exhaust gases (? ≈ 1.4, molecular weight = 26 g/mol) is 1.75 kg/s. The exhaust gases enter the nozzle with stagnation pressure and temperature equal to Po = 300 kPa and To = 500 K, respectively a) What is the optimal cruising altitude for the operation of the nozzle of this UAV? (b) What is the lowest altitude at which the plane can fly such that the flow inside the diverging part of the nozzle is kept supersonic? Note: - Assume that the stagnation conditions of the flow of exhaust gases entering the nozzle are kept constant with varying altitude
Air (? = 1.225 kg/m3 and ? = 1.789 × 10−5 kg/m⋅s) flows in a wind tunnel, and the wind tunnel speed is measured with a Pitot-static probe. For a certain run, the stagnation pressure is measured to be 560.4 Pa gage and the static pressure is 12.7 Pa gage. Calculate the wind-tunnel speed.
Air flows isentropically through a duct. At section 1, thepressure and temperature are 250 kPa and 125°C, andthe velocity is 200 m/s. At section 2, the area is 0.25 m2 andthe Mach number is 2.0. Determine (a) Ma1; (b) T2; (c) V2;and (d ) the mass fl ow.
Air is kept in a tank at pressure Po = 689 KPa abs and temperature To = 17°C. If one allows the air to issue out in a one-dimensional isentropic flow, the greatest possible flow per unit area is Blank 1 kg/m2-s. For air, Use R = 287 J/kg-K and Mol. Wt. = 29.1 *Express your answers in whole significant figure without decimal value and without unit*
The pressure-density relation for ethanol is approximatedby Eq. with B =1600 and n = 7. Use this relation toestimate the speed of the sound of ethanol at 2000 atmospheres.
impact of a jet Draw the relationship of the Fact against the jet velocity Vj
The static and stagnation pressures of a fluid in a pipe are measured by a piezometer and a pitot tube to be 200 kPa and 220 kPa, respectively. If the density of the fluid is 600 kg/m^3, the velocity (in m/s) of the fluid is ?"

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Air enters a nozzle that has an inlet area of 0.4 m2 , at 200 kPa , 500 °C, and 30 m/s . At the exit the conditions are 100 kPa and 443 Part A If the exit area is 45 cm² , determine the steady-state exit velocity. Use the IG flow-state TESTcalc.