b) Air flows through a cylindrical duct at a rate of 2.3 kg/s. Friction between air and the duct and friction within air can be neglected. The diameter of the duct is 10cm and the air temperature and pressure at the inlet are T₁ 450 K and P₁ = 200 kPa. If the Mach number at the exit is Ma2 1, determine the rate of heat transfer and the pressure difference across the duct. The constant pressure specific heat of air is Cp 1.005 kJ/kg.K. The gas constant of air is R = 0.287 kJ/kg-K and assume k = 1.4.

b) Air flows through a cylindrical duct at a rate of 2.3 kg/s. Friction between air and the duct and friction within air can be neglected. The diameter of the duct is 10cm and the air temperature and pressure at the inlet are T₁ 450 K and P₁ = 200 kPa. If the Mach number at the exit is Ma2 1, determine the rate of heat transfer and the pressure difference across the duct. The constant pressure specific heat of air is Cp 1.005 kJ/kg.K. The gas constant of air is R = 0.287 kJ/kg-K and assume k = 1.4.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A fan running at 1480 rpm takes in 6 m^3/min of air at inlet conditions of P_1=950 mbar and T_1=15^0 C. If the fan impeller dimeter is 40 cm and the table tip air angle 20^0, determine the total pressure developed by the fan and the impeller width at exit. Take the radial velocity at the exit as 0.2 times the impeller tip speed. State the assumptions used.
Blowers are used in wastewater treatment plants to assist microorganisms in degrading pollutants. The impeller of a centrifugal blower has a radius of 15 cm and a blade width of 6.1 cm at the inlet, and a radius of 30 cm and a blade width of 3.4 cm at the outlet. The blower delivers atmospheric air at 20°C and 95 kPa. Disregarding any losses and assuming the tangential components of air velocity at the inlet and the outlet to be equal to the impeller velocity at respective locations, determine the volumetric flow rate of air when the rotational speed of the shaft is 800 rpm and the power consumption of the blower is 120 W. Also determine the normal components of velocity at the inlet and outlet of the impeller.
The pressure-density relation for ethanol is approximatedby Eq. with B =1600 and n = 7. Use this relation toestimate the speed of the sound of ethanol at 2000 atmospheres.
A hydroelectric power plant uses Pelton-type turbines, in which multiple nozzles are used to accelerate the waterwhich is directed onto the turbine blades, which are exposed to an atmospheric pressure of 101.325 kPa. The water enters the nozzles with an absolute pressure of 500 kPa and a speed of 5 m/s, and the nozzle outlets are exposed to atmospheric pressure and have an internal diameter of 5 cm. Consider that the specific mass of water is 1,000 kg/m3. Determine the mass flow rate of water through each of the nozzles, and explain why the actual mass flow rate will be lower.
The flow just upstream of a normal shock wave is given byp1 = 1800 lb/ft2, T1 = 480 ◦R, and M1 = 3.1. Calculate the velocity andM∗ behind the shock.
Orange juice is flowing through a horizontal U-type reducing bend at a rate of 36kg/s. The cross-sectional area, gage pressure, and velocity are 168cm^2, 57.5 kPa, and 2.10 m/s at the inlet, and 80cm^2, 50kPa, and 4.37 m/s at the outlet. Calculate the force applied to the reducing bend by the orange juice in the horizontal direction
A fluid moves in a steady flow manner between two sections in a flow line. At the entrance section A1 = 1m², V1= 0.5 m/s, P1= 4kgm/m³. At the exit section: A2 = 0.2m², V2= 0.20m³/kgm. Calculate the mass flow rate in kg/s and the speed at section 2 in m/s.
Shock waves are treated as discontinuities here, but theyactually have a very small fi nite thickness. After giving itsome thought, sketch your idea of the distribution of gasvelocity, pressure, temperature, and entropy through theinside of a shock wave.
Here, air (105 kPa) at 37 degrees celcius is flowing upward in a 6cm diamater inclined duct, at a rate of 90 L/s. In this case the density of air is 1.1 kg/m3. The diameter of the duct reduces to 4cm through a reducer and a pressure charge occurs. This pressure change is measured by a water manometer. The elevation difference between the points where the two arms of the manometer are attached is 0.2 meters. What is the differential height between the fluid levels in the two manometer arms?
A large vessel contains compressed air at To = 350 K and Po = 2 bar. A converging-diverging nozzle is attached to the vessel to discharge air. The throat area of the nozzle is 200 cm2. At the exit, the pressure is 20 kPa and the flow is supersonic. Answer the followings:
Air fl ows adiabatically in a 3-cm-diameter duct, withf 5 0.018. At the entrance, T1 = 323 K, p1 =200 kPa, andV1 = 72 m/s. (a) What is the mass fl ow? (b) For what tubelength will the fl ow choke? (c) If the tube length is increasedto 112 m, with the same inlet pressure and temperature,what will be the new mass fl ow?
A reducing elbow is used to deflect water flow at 25 L/s in a horizontal pipe upward by an angle of=45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow is 15 cm at the inlet and 5 cm at the exit. The elevation difference between the center of the exit and inlet is 40 cm. The mass of the elbow and the water in it is 40 kg. Determine the anchoring force needed to hold the elbow in place, assuming a momentum-flux correction factor of 1.03.