Air enters the compressor of a gas turbine power plant at 96 kPa and 25 °C. It came out at 1MPa, 327 °C and velocity of 120 m/s. Velocity at the entrance is small and can be ignored.1.The compressor is cooled at a rate of 1500 kJ/min. Compressor input power is 300 kW.Calculate the air mass flow rate and cross sectional area of the outlet. (R=0.287 kJ/kg.K,Cp=1.005 kJ/kg.K)

Answered: Image /qna-images/answer/c9a853d2-8b86-4a53-acdc-a992f3f0727b.jpg

Air enters the compressor of a gas turbine power plant at 96 kPa and 25 °C. It came out at 1 MPa, 327 °C and velocity of 120 m/s. Velocity at the entrance is small and can be ignored. The compressor is cooled at a rate of 1500 kJ/min. Compressor input power is 300 kW. Calculate the air mass flow rate and cross sectional area of the outlet. (R=0.287 kJ/kg.K, Cp=1.005 kJ/kg.K)

Air enters the compressor of a gas turbine power plant at 96 kPa and 25 °C. It came out at 1 MPa, 327 °C and velocity of 120 m/s. Velocity at the entrance is small and can be ignored. The compressor is cooled at a rate of 1500 kJ/min. Compressor input power is 300 kW. Calculate the air mass flow rate and cross sectional area of the outlet. (R=0.287 kJ/kg.K, Cp=1.005 kJ/kg.K)

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A “typical” human body has a surface area of about 1.9 m2 and a surface temperature of about 33oC (306K), a little cooler than the core temperature. If they are radiating heat at a rate of 804W, what is their emissivity? Do not actually solve the problem numerically or algebraically, just pick the one equation and define the relevant knowns and single unknown
A steel ball (200mm in diameter) was heated to around 10000d C and was placed inside a vacuum chamber. What is the rate of heat transfer, in watts through radiation from the ball to the surrounding area?use "K=73+ d C" let the emissivity be equal to 0.32 (3 decimal places)
A cylindrical vessel (D=108,02 cm) is filled with water (ρ=1000 kg/m3, c=4.187 kJ/kg.K) to a depth of 138,6 cm. The initial temperature of the water is 15°C. Determine the time [min] required to increase the water temperature to 50°C when it is immersed into tank, filled with oil at 105°C. (NOTE: The overall heat transfer coefficient between the oil and the water is 284 W/m2.K. The surface area is 4.2 m2.)
Air at 20°C (1 atm) enters into a 5-mm-diameter and 10-cm-long circular tube at an average velocity of 5 m/s. The tube wall is maintained at a constant surface temperature of 160°C. Determine the convection heat transfer coefficient and the outlet mean temperature. Evaluate the air properties at 50°C.
the surface area of a picnic cooler is 2.10 m^2 and it has walls constructed of a material 1.50 cm thick that has a thermal conductivity of 2.00 X 10^-2 W/(m x degrees celsius). If the temperatures inside and outside are 0.0 degress celsius and 28.5 degrees celsius, determine the rate of heat flow into the freezer and the time required to melt 2.50 kg of ice inside the cooler at 0.0 degrees celsius
In 2000, a gargantuan iceberg broke away from the Ross Ice Sheet in Antarctica. It was approximately a rectangle with dimensions 295 km295 km long, 37.0 km37.0 km wide, and 250.0 m250.0 m thick. What is the mass of this iceberg, given that the density of ice is 917 kg/m3917 kg/m3? How much heat transfer ?Q in joules is needed to melt the iceberg? Assume that the temperature of the iceberg is uniform at 0∘C.0⁢∘C. The latent heat of fusion for water is 334 kJ/kg. How many years would it take sunlight alone to melt ice this thick if the ice absorbs an average of 113 W/m2,113 W/m2, 12.0 h12.0 h per day?
Methane, which constitutes the majority of natural gas, is sometimes stored in condensation tanks in an oil and gas field. If the vaporirzed methane above the liquid is at a temperature of 28.9˚C on a hot summer day with a density of 2.05 kg/m3, at what pressure in Pascals would the gas be? The specific gas constant for methane is 518 J/(kg K).
What horsepower is required to isothermally compress 800 ft3 of air per minute from 14.7 psia to 120 psia?
The tube in a heat exchanger has a 2-in inner diameter and a 3-in outer diameter. The thermal conductivity of the tube material is 0.5 Btu/h·ft·°F, while the inner surface heat transfer coefficient is 50 Btu/h·ft2·°F and the outer surface heat transfer coefficient is 10 Btu/h·ft2·°F. Determine the overall heat transfer coefficients based on the outer and inner surfaces.
What is the volume of 10 mol of gas at the temperature 14°C when the pressure is 138 kPa? Answer in the unit of m3. Be careful with units. Use R = 8.314 J/(K mol) for the gas constant
A long iron rod (r = 7870 kg/m3, cp = 447 J/kg·K,k = 80.2 W/m·K, and a = 23.1 * 10–6 m2/s) with diameter of25 mm is initially heated to a uniform temperature of 700°C.The iron rod is then quenched in a large water bath that is maintained at constant temperature of 50°C and convection heat transfer coefficient of 128 W/m2·K. Determine the time required for the iron rod surface temperature to cool to 200°C. Solve this problem using analytical one-term approximation method (not the Heisler charts).
2) (a) Calculate the hourly heating load of a house in which all exterior surfaces have a thermal resistance of R= 20 ft2hoF/Btu, the inside temperature is 70oF, and the outside temperature is 0oF. The dimensions of the house are 40ft x 40ft x 40ft. (b) calculate the calculation of the infiltration heat loss. Assume K-value of air exchanges per hour is 2. (HINT: Lecture 10, Slide 25 & 32-34) 3) An 80 kg man is standing on ice that can withstand 5000 Pa of pressure. a) If he is standing, having a total contact area from both feet of 0.1 m2. How much pressure is the applying, and will he fall through the ice? b) Suppose the man lies down on the ice, increasing his contact area to 0.8 m2. How much pressure is the applying, and will he fall through the ice? 4) Convert the concentration of helium and hydrogen from ppM to percentage.