Cold water (cp = 4180 J/kg·K) leading to a shower enters a thin-walled double-pipe counter-flow heat exchanger at 15°C at a rate of 0.25 kg/s and is heated to 45°C by hot water (cp = 4190 J/kg·K) that enters at 100°C at a rate of 3 kg/s. If the overall heat transfer coefficient is 950 W/m2·K, determine the rate of heat transfer and the heat transfer surface area of the heat exchanger using the «2NTU method.

Cold water (cp = 4180 J/kg·K) leading to a shower enters a thin-walled double-pipe counter-flow heat exchanger at 15°C at a rate of 0.25 kg/s and is heated to 45°C by hot water (cp = 4190 J/kg·K) that enters at 100°C at a rate of 3 kg/s. If the overall heat transfer coefficient is 950 W/m2·K, determine the rate of heat transfer and the heat transfer surface area of the heat exchanger using the «2NTU method.

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter21: Heat And The First Law Of Thermodynamics

Section: Chapter Questions

Problem 21PQ

See similar textbooks

Similar questions

An aluminum rod 0.500 m in length and with a cross-sectional area of 2.50 cm2 is inserted into a thermally insulated vessel containing liquid helium at 4.20 K. The rod is initially at 300 K. (a) If one-half of the rod is inserted into the helium, how many liters of helium boil off by the time the inserted half cools to 4.20 K? Assume the upper half does not yet cool. (b) If the circular surface of the upper end of the rod is maintained at 300 K, what is the approximate boil-off rate of liquid helium in liters per second after the lower half has reached 4.20 K? (Aluminum has thermal conductivity of 3 100 W/m K at 4.20 K; ignore its temperature variation. The density of liquid helium is 125 kg/m3.)
The tube in a heat exchanger has a 2-in inner diameter and a 3-in outer diameter. The thermal conductivity of the tube material is 0.5 Btu/h·ft·°F, while the inner surface heat transfer coefficient is 50 Btu/h·ft2·°F and the outer surface heat transfer coefficient is 10 Btu/h·ft2·°F. Determine the overall heat transfer coefficients based on the outer and inner surfaces.
A test is conducted to determine the overall heat transfer coefficient in a shell-and-tube oil-to-water heat exchanger that has 24 tubes of internal diameter 1.2 cm and length 2 m in a single shell. Cold water (cp = 4180 J/kg·K) enters the tubes at 20°C at a rate of 3 kg/s and leaves at 55°C. Oil (cp = 2150 J/kg·K) flows through the shell and is cooled from 120°C to 45°C. Determine the overall heat transfer coefficient Ui of this heat exchanger based on the inner surface area of the tubes.
Cold water (cp = 4180 J/kg·K) enters the tubes of a heat exchanger with 2-shell passes and 20-tube passes at 20°C at a rate of 3 kg/s, while hot oil (cp = 2200 J/kg·K) enters the shell at 130°C at the same mass flow rate and leaves at 60°C. If the overall heat transfer coefficient based on the outer surface of the tube is 220 W/m2·K, determine (a) the rate of heat transfer and (b) the heat transfer surface area on the outer side of the tube.
Water enters a 2.5-cm-internal-diameter thin copper tube of a heat exchanger at 15°C at a rate of 0.3 kg/s, and is heated by steam condensing outside at 120°C. If the average heat transfer coefficient is 800 W/m2·°C, determine the length of the tube required in order to heat the water to 115°C
A 5-cm-external-diameter, 10-m-long hot-water pipe at 80°C is losing heat to the surrounding air at 5°C by natural convection with a heat transfer coefficient of 25 W/m2·K. Determine the rate of heat loss from the pipe by natural convection.
How much fiberglass insulation (k = 0.035 W/m*K) is needed to guarantee that the outside temperature of a kitchen oven will not exceed 43 degrees Celsius? The maximum oven temperature to be maintained by the conventional type of thermostatic control is 290 degrees Celsius, the kitchen temperature may vary from 15 to 33 degrees Celsius, and the average heat transfer coefficient between the oven surface and the kitchen is 12 W/m2*K.
A short brass cylinder (r = 8530 kg/m3, cp =0.389 kJ/kg·K, k = 110 W/m·K, and a 5 *.39 3 1025 m2/s) of diameter 8 cm and height 15 cm is initially at a uniform temperature of 150°C. The cylinder is now placed in atmospheric air at 20°C, where heat transfer takes place by convection with a heat transfer coefficient of 40 W/m2·K. Calculate (a) the center temperature of the cylinder; (b) the center temperature of the top surface of the cylinder; and (c) the total heat transfer from the cylinder 15 min after the start of the cooling.
A thin electronic component with a surface area of 950 cm2 is cooled by having a heat sink attached on its top surface. The thermal contact conductance of the interface between the electronic component and the heat sink is 25,000 W/m2∙K. According to the manufacturer, the heat sink has combined convection and radiation thermal resistance of 1.3 K/W. If the electronic component dissipates 45 W of heat through the heat sink in a surrounding temperature of 30°C, determine the temperature of the electronic component. Does the contact resistance at the interface of the electronic component and the heat sink play a significant role in the heat dissipation?
The roof of a house consists of a 15-cm-thick concrete slab (k = 2 W/m·K) that is 15 m wide and 20 m long. The convection heat transfer coefficients on the inner and outer surfaces of the roof are 5 and 12 W/m2·K, respectively. On a clear winter night, the ambient air is reported to be at 10°C, while the night sky temperature is 100 K. The house and the interior surfaces of the wall are maintained at a constant temperature of 20°C. The emissivity of both surfaces of the concrete roof is 0.9. Considering both radiation and convection heat transfers, determine the rate of heat transfer through the roof, and the inner surface temperature of the roof. If the house is heated by a furnace burning natural gas with an efficiency of 80 percent, and the price of natural gas is $1.20/ therm (1 therm = 105,500 kJ of energy content), determine the money lost through the roof that night during a 14-h period.
Two concentric spheres of diameters 15 cm and 25 cm are separated by air at 1 atm pressure. The surface temperatures of the two spheres enclosing the air are T1 = 350 K and T2 = 275 K, respectively. Determine the rate of heat transfer from the inner sphere to the outer sphere by natural convection.
Consider an opaque plate that is well insulated on the edges and it is heated at the bottom with an electric heater. The plate has an emissivity of 0.67, and is situated in an ambient surrounding temperature of 7°C where the natural convection heat transfer coefficient is 7 W/m2?K. To maintain a surface temperature of 80°C, the electric heater supplies 1000 W/m2 of uniform heat flux to the plate. Determine the radiosity of the plate under these conditions.