Answered: Air is flowing in pipe as shown in…

Air is flowing in pipe as shown in figure. If u = 10 m/s, the manometer reading is (use g = 10 m/s². PAir = 1.2 kg/m³) u Air 0 X Water

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 49P

See similar textbooks

Related questions

Q: In the figure below, one end of a uniform beam of weight 943 N is hinged to a wall; the other end is…

Q: A sediment reservoir is planned for a 2100 sq.m site that has a peak inflow of 120cumec. The runoff…

A: Given- 2100 sq.m site, Peak inflow=120 cumec, 4 cm rainfall, Runoff = 2.04 cm, Peak capacity = 50…

Q: MODULAR 01 - STRUCTURAL THEORY ANALYSIS OF STRUCTURES PART 2. Determine the reactions at supports.…

A: Static Indeterminacy= m+r-2j = 7+3-2*5 = 0 Determinate structure, hence can be solved by equilibrium…

Q: An object weighing 100 N in the air was found to weight 75 N when fully submerged in water. The…

A: Given data- Weight of the object W=100 N, Weight in water =75 N, To Find- The relative density RD of…

Q: Determine the reaction at B for the beam shown below. 100 KN -3 m O a. By=115 kN ↑ O b. By = 120 kN…

A: Given, UDL = 20 kN Point load = 100 kN Length of beam = 12 m

Q: support reactions: determine the reactions at the suuports

A: Given,

Q: The beam supports the load of P = 5.7 kip. As a result, the A-36 steel member BC is subjected to a…

A: Given : P = 5.7 kip This question is from structural analysis. Determine Factor of safety with…

Q: Determine the drawdown at a distance of 50 m from a well pumping constantly at 50 US gpm after one…

Q: Question- A vertical photograph was taken at an altitude of 2000 m above mean sea level. If the…

A: Given- Altitude H=2000 m, Photograph elevation=250 m, Scale S=1:1000,

Q: Refer to the closed traverse in the following figure. 1.) The interior angle B, which is unknown.…

A: Solution: 1) The interior angle B: B=180o+6o15'+29o38'=225o53' 2) The azimuth from South of lines AB…

Q: Q3. A free jet of water with an initial diameter of 2 in strikes the vane as shown in the figure…

A: Given data, Initial diameter= 2 in Angel of bend = 30° Initial velocity = 100 ft/sec Final…

Q: Problem-3 b A hollow shaft of 20 mm diameter and 16 mm inside diameter is subjected to a torque of…

A: Given- Outside diameter D=20 mm, Inside diameter d=16 mm, Torque T=40 N-m, It is needed to find the…

Q: Problem 4. Determine the maximum deflection and slope. [5+0.5a] kN/m A 3 m [2.5+0.25b] kN B 3 m C a…

Q: Problem 7: A rectangular concrete beam section was cast without any web or shear reinforcement, as…

Q: (see App sectional properties) can support if it is 7 m long and a factor of safety of 1.98 is…

A: Given Data- Steel column - HSS 254 x 152.4 x 12.7 Length of beam (L) = 7 m factor of safety = 1.98…

Q: Questions 1. What is the soundness of cement? 2. What is the purpose of soundness test? 3. How is…

A: There are various physical and chemical properties of cement, which affect the setting time,…

Q: 8.15) The flow rate and water depth just upstream of a dam are 15 m³/s and 4.0 m respectively. The…

A: Reference : Fluid mechanics, Rectangular Channel section. Given : Flow rate, water depth, width ,…

Q: The Figure n°3 represents two walls of a low building (made of reinforce concrete) but connected…

A: Figure n°3 depicts what seems to be a shear failure, which was brought about by an unequal…

Q: 2. Determine the bar force in member BD. Use Method of Joints. D ww 097 A E /m 10 B 25 kip, 25 kip…

A: Given Data Find the forces in the member BD using method of joints.

Q: Determine the reactions at supports. Also, draw the shear and moment diagram. Note: c= 8 d= 1

A: Given Data c = 8 d = 1 Find support reaction and draw shear force and bending moment diagram.…

Q: 16 in. 20 in. r = 38 in. In the fig. shown, compute the following: X (a) Components of the centroid…

A: Given, to determine, (a) Components of the centroid (b) The total moment of inertia with respect to…

Q: Write the V and M equation of the beams loaded as shown and the diagram. Then repeat the method…

Q: the bearing of line AB is N 75° E, and the azimuth of line BC from north meridian is 98°. If the…

A: Given that bearing of line AB is N 75° E

Q: 4. Determine the force in members CE, CF, and DF shown in Figure 4. Use Method of Sections. State…

A: Given data in question Load 12 kN Span 9.6 m Height 1.8 m To find out Member forces CE, CF &…

Q: 2 m -2m -3 kN -2m Determine the force in each member of the truss shown in the figure. Indicate…

A: Given Data Find the forces in each member.

Q: Determine the force in member BC and FC and FE by the Method of Joints. State if the member is in…

Q: (2) 10' 12' 11' ↓ Pu ↑ Pu H →Þ. 33' ↑ Pu H A992 W 14 x 82 PDL = 2 PLL What is PLL = ? GiveN = Ag =…

A: Given data: Section W14×82 Ag=24 in2, rxx=6.05 in, ryy=2.48 in For the given end conditions for the…

Q: Determine the reaction at A for the beam shown below. 3m O a. Ay = 246 kN ↓ O b. Ay = 148 kN ↓ O c.…

Q: An aerial photograph of a terrain is taken at a scale of 1:8500, For 3000 m altitude of the flight…

Q: Given: Consider the beam below with support of the compression flange only provided at the ends of…

A: The given figure is shown below:

Q: An annual flood series contains 100 years of flood data. For a return period of 200 years the…

A: Given data: An annual flood series contains 100 years of flood data. Return period, T = 200 years.

Q: If the Greenwich civil time is 20hr30m15s P.M on june 13, 2019. Find the LMT for place 120degreeW

Q: The quarter cylindrical gate AB has a radius of 1.5 m and length 2.4 m perpendicular to the paper.…

A: Hydrostatic force is defined as the resultant force due to the pressure load of a liquid acting on a…

Q: 13. Refer to Figure 3.1 attached. In the flexible pavement design example illustrated in the figure,…

A: Given: Estimated total 18 kips equivalent single axle load application, W18 = 2,000,000 To find: The…

Q: Explain why indoor air pollution levels can be much higher than ambient levels.

A: Air Pollution: The contamination of air due to atmospheric pollutants or any other pollutants in the…

Q: Compute

Q: An open, clean glass tube (0 = 0) is inserted vertically into a pan of water. The surface tension of…

A: Given- Surface tension =7.34×10-2 N/m, Open clean glass tube,

Q: The hook shown in the figure is subjected to a force of F=28 N that makes an angle of cwith the…

Q: As per IS 800, the efficiency of a riveted joint having the minimum pitch is: 1. 60% 2. 70% 3. 40%…

Q: Describe and discuss in detail indirect waste and how is it handled?

A: Indirect waste- A drain pipe that exits a water pipe or fixture and empties into another waste pipe…

Q: E = 200 GPa 48 kN/m DA section is 8 KN Im 5130 X 15 BA

Q: Following are the measured values of the angle 'A' with their respective weights. ZA = 56°15'00';…

Q: Determine the moments of inertia I, and I of the area shown about vertical and horizontal axes…

Q: The angle of intersection equal to 116, what is the length of curve of the curve (in meters) if the…

Q: Laboratory results on a soil have shown that its unconfined compressive strength is 1.2 kg/cm2. In a…

Q: For an aircraft to take off from Sydney. airport, the required length of runway at sea level in…

Q: The AASHTO present serviceability index (PSI) correlates the PSR to actual pavement performance in…

A: The original AASHO Road Test PSR serves as the foundation for the current serviceability index…

Q: A parabolic vertical curve with a grade in of 2.1%, a grade out of - 3.2%, a curve length of…

A: (Note: Since part C is asked to solve, the solution for the c part is given below.) Given: Grade in,…

Q: The Howe truss is subjected to the loading shown. Determine the support reaction forces and the…

Q: 2.Find the surface tension in N/m in a soap bubble of 30 mm diameter when the inside pressure is…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

Air is flowing in pipe as shown in figure. If u = 10 m/s, the manometer reading is (use g = 10 m/s², PAir
= 1.2 kg/m³)
Air
+0.
X
→ Water

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Pitot tube is an instrument that is used to measure flowrate in a pipe. Figure 3 shows water flowing through a pipe with pitot tube attached to a U-tube manometer containing Fluid X. Given the difference in height in the manometer, h, calculate the flowrate through the pipe by showing the application of Bernoulli Equation and Hydrostatic Pressure Equation. Details of the parameters are as follows; Difference in manometer, h = 0.1 m Density of water = 1000 kg/m3 Density of Fluid X = 12000 kg/m3 Diameter of pipe = 0.3m
Write F if true and T if false 4. a Gravimeter measures the Gravity Field to determine changes in rock density in the Earth’s crust
The figure shows gate AB, 4 meters high, submerged in water. It is inclined 40 degrees with respect to the horizontal. Using the figure shown, determine the distance of CG (center of gravity) to CP (center of pressure) in meters.
SOLVE FOR 30 MINUTES.
The figure shows a system where water flows from a tank through a system of pipes of different sizes and elevations. If we assume that there is no energy loss in the system, find: a. The volumetric flow through the pipe in ft3/sb. The pressure at point Bc. The pressure at point Cd. The flow velocity at point F in ft/s
Find : The distance (in meters) of cylinder C travels in 3 seconds
In figure 6, compute the pressure difference between m and n, in pounds per square inch, when: (a) Fluid A is brine (sp gr 1.15), the gage fluid is oil (sp gr 0.92), and z = 45.15 in. (b) Fluid A is water, the gage fluid is air, and z = 15.15 in.
3. A vertical piston-cylinder device on the left containing a gas has a mass of 40 kg and a cross-sectional area of 0.012 m². The local atmospheric pressure is 95 kPa, and the gravitational acceleration is 9.81 m/s². Determine the absolute pressure (kPa) inside the cylinder. (2 decimal)
In the figure below, the weight of the block is 300 kg and the angle of internal friction is 24.2 degrees. a. If h = 50 cm and P = 50 kg. does the block move? b. If h = 50 cm, what is the smallest P to start motion?
In the figure below, the weight of the block is 300 kg and the angle of internal friction is 24.2 degrees.a. If h = 50 cm and P = 50 kg. does the block move?b. If h = 50 cm, what is the smallest P to start motion?
A stream of water, 3” in diameter, discharges into the atmosphere at a velocity 80.0 ft/sec. Find the horsepower in the jet using the datum plane through the center of the jet. Draw the figure. And solve using the formula on the Image uploaded.
fluıd mechanıcs If an oil tank is pulled uphill on a surface that makes an angle of 162 with the horizontal, the oil makes an angle of 160,a) Show the forces acting on the tank on the figure. Write the balance of force.b) Calculate the constant acceleration of the tank being pulled uphill.