Air (y = 1.4 and R = 0.287 kJ/kg · K) enters a constant-area insulated duct with a Mach number of 0.35, a stagnation pressure of 105 kPa, and stagnation temperature of 300 K. For a duct length of 50 cm, duct diameter of 1 cm, and friction coefficient of 0.022, determine pressure and velocity at the inlet and outlet sections and the mass flow rate of the air.

Air (y = 1.4 and R = 0.287 kJ/kg · K) enters a constant-area insulated duct with a Mach number of 0.35, a stagnation pressure of 105 kPa, and stagnation temperature of 300 K. For a duct length of 50 cm, duct diameter of 1 cm, and friction coefficient of 0.022, determine pressure and velocity at the inlet and outlet sections and the mass flow rate of the air.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

show that the governing equation for axisymmetric stagnation flow is ϕ ′′′ + 2ϕϕ′′ − ϕ ′2 + 1 = 0 what is the thickness of viscous layer near the axisymmetric stagnation point?
Air is cooled as it flows through a 30-cm-diameter duct. The inlet conditions are Ma1 = 1.2, T01 = 350 K, and P01 = 240 kPa and the exit Mach number is Ma2 = 2.0. Disregarding frictional effects, determine the rate of cooling of air.
How does the Mach number affect the behavior of compressible flow in a supersonic nozzle?
A long pipe of 0.0254 m diameter has a mean coefficient of friction of 0.003. Air enters the pipe at a mach number of 2.5, stagnation temperature 310 K and static pressure 0.507 bar. Determine for a section at which the mach number reaches 1.2: i) Static pressure and temperature, ii) Stagnation pressure and temperature, iii) Velocity of air, iv) Distance of this section from the inlet and v) mass flow rate of air.
Consider supersonic flow impinging on the rounded nose of an aircraft. Is the oblique shock that forms in front of the nose an attached or a detached shock? Explain.
Fuel with heating value (HV) of 39,000 kJ/kg is burned by spraying in to 16-cm-diameter tabular combustionchamber. The air enters at 450 K, 380 kPa, and 55 m/s as shown in Figure Q3. If the exit Mach number is 0.8,determine (a) the exit temperature and,(b) the rate at which the fuel is burned.Properties of air: Specific heat capacity ratio k = 1.4, Specific heat at constant pressure c, = 1.005 kJ/kg.K,and Gas constant R = 0.287 kJ/kg.K.Use Appendix 2 for Rayleigh flow functions for an ideal gas with k = 1.4 Assume:1. Rayleigh flow (i.e., steady one-dimensional flow of an ideal gas with constant properties through aconstant cross-sectional area duct with negligible frictional effects) are valid. 2. combustion is compleso, and it is treated as a heat addition process, with no change in the chemical composition of flow 3.The increase in mass flow rate due to fuel in ection is disregardeo.
Consider the supersonic flow of air over a two-dimensional wedge with a half angle of 10 degrees at 70 kPa, 260 kelvin, and mach number 2.4 after shock. If the axis of the wedge is tilted 25 degrees beforehand, determine the post-shock Mach number, temperature and pressure on the wedge.
What is the effect of heating the fluid on the flow velocity in subsonic Rayleigh flow? Answer the same questions for supersonic Rayleigh flow.
Consider supersonic Fanno flow that is decelerated to sonic velocity (Ma = 1) at the duct exit as a result of frictional effects. If the duct length is increased further, will the flow at the duct exit be supersonic, subsonic, or remain sonic? Will the mass flow rate of the fluid increase, decrease, or remain constant as a result of increasing the duct length?
Air flowing steadily in a nozzle experiences a normal shock at a Mach number of Ma = 2.6. If the pressure and temperature of air are 58 kPa and 270 K, respectively, upstream of the shock, calculate the pressure, temperature velocity, Mach number, and stagnation pressure downstream of the shock. Calculate the entropy changes of air and helium across the normal shock wave
Consider air entering a heated duct at p1 = 1 atm and T1 = 288 K. Ignore the effect of friction. Calculate the amount of heat per unit mass (in joules per kilogram) necessary to choke the flow at the exit of the duct for an inlet Mach number of M1 = 2.2.
Air enters a converging–diverging nozzle, as shown at 1.0 MPa and 800 K with negligible velocity. The flow is steady, one-dimensional, and isentropic with k = 1.4. For an exit Mach number of Ma = 2 and a throat area of 20 cm2, determine (a) the throat conditions, (b) the exit plane conditions, including the exit area, and (c) the mass flow rate through the nozzle.