al cycle has an initial temperature of 30°C. The compression ratio is 6 and the heat addition at constant volume ess is 600 KJ/kg. If expansion ratio is 2.5, the maximum temperature of the cycle is || K. cv=0.7186 kJ/kg-K. al answer must be in TWO DECIMAL PLACES. DO NOT round off in between solutions. DO NOT include the unit - final answer)

al cycle has an initial temperature of 30°C. The compression ratio is 6 and the heat addition at constant volume ess is 600 KJ/kg. If expansion ratio is 2.5, the maximum temperature of the cycle is || K. cv=0.7186 kJ/kg-K. al answer must be in TWO DECIMAL PLACES. DO NOT round off in between solutions. DO NOT include the unit - final answer)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a two stage compression and two stage expansion in an ideal gas-turbine cycle. The air enters each stage of the compressor at 350 K and each stage of the turbine at 1240 K. The pressure ratio across each stage of the compressor and turbine is 3.5. Assuming an efficiency of 82 percent for each compressor stage and an efficiency of 88 percent for each turbine stage. Determine the thermal efficiency of the cycle, assuming (a) no regenerator is used and (b) a regenerator with 85 percent effectiveness is used.
A four-cylinder, four-stroke, 1.6-L gasoline engine operates on the Otto cycle with a compression ratio of 11. The air is at 100 kPa and 37°C at the beginning of the compression process, and the maximum pressure in the cycle is 8 MPa. The compression and expansion processes may be modeled as polytropic with a polytropic constant of 1.3. Using constant specific heats at 850 K, determine the engine speed for a net power output of 50 kW.
The temperature of air at the beginning of compression in an Otto cycle is 310 K and maximum temperature in the cycle is 2200 K. If the pressure at the end of adiabatic compression is 15 times that at the start, determine the compression ratio, thermal efficiency, and work done. Take k for air = 1.4.
A gas turbine power plant operates on a standard air cycle between extreme pressures of 1 and 6.4 bar. The inlet air temperature is 22°C and the turbine inlet limit temperature is 807°C. The adiabatic efficiencies of the compressor and the turbine are 0.82 and 0.85, respectively. If a regenerator with an efficiency of 0.80 is installed and two ideal stages are used in compression and expansion, determine the thermal efficiency.
An ideal diesel engine has a compression ratio of 20 and uses air as the working fluid. The state of air at the beginning of the compression process is 95 kPa and 20°C. If the maximum temperature in the cycle is not to exceed 2200 K, determine the net work of the system as a function of compression ratio, r.
In an ideal diesel cycle the pressure and temperature at the beginning of the adiabatic compression are 98.5kN/m squared and 60 degrees c respectively.The maximum pressure attained during the cycle is 4.5MN/m squared and the heat received during the cycle is 580kJ/kg gas.Determine ,for the cycle, (a) the volume ratio of compression (b) the temperature at the end of compression (c) the temperature at the end of heat reception (d)the temperature at the end od adiabatic expansion
In an air standard gas turbine cycle, air at 14.5 psia and 70 F is first compressed to 80 psia in a compressor of 82 percent efficiency. The hot air leaving the combustion chamber at 1250 F is expanded back to 14.5 psia in a turbine of 85 percent efficiency. If a regenerator is inserted into the cycle to heat the air leaving the compressor to 650 F, determine the thermal efficiency of the cycle and the effectiveness of the regenerator.
1.A piston-cylinder device contains air at 427 degrees and 134kPa. A pressure increase of 1.378kPa was recorded after the air was compressed isentropically with minimum work input of 1.422KJ. Assuming air has constant specific heats evaluated at given temperature. Determine the mass of air in the device. 2. Air is used as the working fluid in a simple ideal brayton cycle that has a pressure ratio of 12, a compressor inlet temperature of 300k, and a turbine inlet temperature of 1000k. Determine the required mass flow rate in (kg/s) of air for a net power output of 70MW, assuming both the compressor and the turbine have an isentropic efficiency of 100%. Assume constant specific heats at room temperature
How is the rpm (revolutions per minute) of an actual four-stroke gasoline engine related to the number of thermodynamic cycles? What would your answer be for a two-stroke engine?
An air-standard Carnot cycle is executed in a closed system between the temperature limits of 350 and 1200 K. The pressures before and after the isothermal compression are 150 and 300 kPa, respectively. If the net work output per cycle is 0.5 kJ, determine (a) the maximum pressure in the cycle, (b) the heat transfer to air, and (c) the mass of air. Assume variable specific heats for air.
In an ideal Otto cycle, the ratio of the maximum volume to the minimum volume is 8. The maximum temperature of the cycle is 1,290 K while the minimum temperature is 301 K. Determine the work net in kJ/kg. Use k = 1.4, Cv = 0.718 kJ/kg-K and Cp = 1.005 kJ/kg-K. For the final answer, use two decimal places.
Consider a regenerative gas-turbine power plant with two stages of compression and two stages of expansion. The overall pressure ratio of the cycle is 9. The air enters each stage of the compressor at 300 K and each stage of the turbine at 1200 K. Accounting for the variation of specific heats with temperature, determine the minimum mass flow rate of air needed to develop a net power output of 110 MW.