An 1100 kg truck is being used to raise a 100 kg box using the setup shown below. When the box is at a height of 3m, the box has a velocity of 1 m/s. a) How far did the truck travel to lift the box this high? (This is a dependent motion problem) b) What is the velocity of the truck at this time? c) What is the work that the truck has done over this time? 1100 kg 4m 100 kg 5m

An 1100 kg truck is being used to raise a 100 kg box using the setup shown below. When the box is at a height of 3m, the box has a velocity of 1 m/s. a) How far did the truck travel to lift the box this high? (This is a dependent motion problem) b) What is the velocity of the truck at this time? c) What is the work that the truck has done over this time? 1100 kg 4m 100 kg 5m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cyclist rides at an average speed of 18 miles per hour. If she wants bike 212 km, how long (in hours) must she ride?
I need to lift a large engine block but at my age, I can only create 160lbs of force. I will build a lever to assist me. The fulcrum is placed 1.5 ft away from the 575lb block. How far away will i need to be from the fulcrum to achieve movement of the block?
A machine costs P20,000 today and has an estimated scrap value of P2,000 after 8 years. Inflation is 8% per year. The effective annual interest rate earned on money invested is 8%. How much money needs to be set aside each year to replace the machine with an identical model 8 years from now?
An airplane of mass 5000 kg has to perform an emergency landing.it makes contact with the ground and relied on friction to slow it down . If the ground has a coefficient of friction of 0.5 find the acceleration of the plane . How can I find the answer? I need help
A car weighing 5500 lbm stops at 55 mph. ) a) Energy (in Btu) is dissipated as heat by friction during braking how much? b) Assume all over Vietnam, every day there are 30,000,000 winning processes as above happen. Calculate the average amount of energy (megawatts) expended due to friction?
A 1380 kg block is being pulled across the floor by a rope which is wrapped around a motorized winch. The coefficient of kinetic friction between the block and the floor is 0.41, and the block moves at a constant speed of 1.34 m/s.What is the power output of the motor, in Watts (W)?Calculate the total work done by the winch if the box moves a total of 4.50 meters. Give your answer in Joules (J).
C)If both cyclists have 170 mm cranks on their bikes, what will be the mechanical advantage (considering only the movement of the feet with a constant force for walking and riding), in percent, that each rider will have achieved over walking the same distance? (This can be found by dividing the distance wallked by the distance the feet move in riding.)
Joe takes his little brother Andy down the the playground for an afternoon out. Andy would like to ride the seesaw, but the difference in their sizes, Joe weights 160lbs and Andy weighs 641lbs, makes this difficult. Joe sees a solution from his engineering class and moves the fulcrum from the middle to a new place. The seesaw is 3.5m long. After Joe moved the falcrum how long was the seesaw on Andy's side?
When you lift an object by moving only your forearm, the main lifting muscle in your arm is the biceps. Suppose the mass of a forearm with hand is 1.80 kg. If the biceps is connected to the forearm a distance of 2.50 cm from the elbow, how much force must the biceps exert to hold a 44.5 N (about 10 lbs) ball at the end of the forearm at distance of 35.0 cm from the elbow, with the forearm parallel to the floor, in Newtons? Use g = 10.0 m/s2.
Joe takes his little brother Andy down the the playground for an afternoon out. Andy would like to ride the seesaw, but the difference in their sizes, Joe weights 160lbs and Andy weighs 641lbs, makes this difficult. Joe sees a solution from his engineering class and moves the fulcrum from the middle to a new place. The seesaw is 3.5m long. After Joe moved the fulcrum how long was the seesaw on Joe's side?
Joe takes his little brother Andy down the the playground for an afternoon out. Andy would like to ride the seesaw, but the difference in their sizes, Joe weights 160lbs and Andy weighs 64lbs, makes this difficult. Joe sees a solution from his engineering class and moves the fulcrum from the middle to a new place. The seesaw is 3.5m long. After Joe moved the fulcrum, what is the new mechanical advantage of the seesaw, considering the input from Andy's side of the seesaw?
A wind turbine has the maximum power output at the rated speed of 12 m/s and a rotor diameter of 82 meters. The cut-in and cut-out speeds for this type of wind turbine are 4 m/s and 23 m/s, respectively. The table below shows the annual wind data near a potential site for setting up a wind farm using this type of wind turbine and the power coefficient of the wind turbine at the specific wind speed. The air density is 1.22 kg/m3. (a). What is the maximum power output of this wind turbine, assuming Betz limit? (b). What is the average power output if the wind turbine is installed at this site?. (c). What is the capacity factor of the wind turbine at this site? (d). If a wind farm consisting of 100 such wind turbines is built at the site, how much energy does this wind farm generate in a year (in the unit of kWh)? (e). Is this a good site for using this particular type of wind turbine?