Given the lifting table shown below, The diameter of the plunger Dp 8 cm. The ram diameter DR 48 cm , The efficiency is 100 %, The stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2 kN. Find : a) the force F1 exerted on the plunger , [1] b) the number of strokes needed to raise the load by a distance of 10 cm and [1] c) the movement ratio. [1] Load Plunger Ram

Given the lifting table shown below, The diameter of the plunger Dp 8 cm. The ram diameter DR 48 cm , The efficiency is 100 %, The stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2 kN. Find : a) the force F1 exerted on the plunger , [1] b) the number of strokes needed to raise the load by a distance of 10 cm and [1] c) the movement ratio. [1] Load Plunger Ram

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

The blood pressure in your heart is 1.52 x104 Pa. If an artery in the brain is 0.421 m above the heart, what is the pressure in the artery?
A ship of 7500 tonnes displacement has KM 8.6 m, KG 7.8 m and 20 m beam. A quantity of deck cargo is lost from the starboard side (KG 12 m, and centre of gravity 6 m in from the rail). If the resulting list is 3 degrees 20 minutes to port, find how much deck cargo was lost.
Suppose we got the following data during a test of a 2- stroke engine in which gas is usedas a fuel:Diameter of the piston = 149 mmStroke length = 179 mmClearance volume = 0.88 literrpm of the engine = 302Indicated mean effective pressure = 6.0 barGas consumption = 6.0 m3/hCalorific value of the gas (fuel) = 16990 kJ/m3Make a clear sketch the geometry of this engine using the data and determine thefollowing:i. Indicated power developed by the engine in watt.ii. Air Standard Efficiencyiii. Indicated thermal efficiency of the engine.
State what is Bernoulli's Priciple for Pressure and Velocity? In 8 sentences only.
spring attached 2.00 kg block is stretched 20.0cm and released from rest on a frictionless surface. The measured period is 1.00 sec. a) What is the spring constant k? b)A student doubled the stretched length. what is the period of the spring? c) You want to make a simple pendulum and a physical pendulum which is a uniform bar, and you want same period with the spring’s period, 1.00sec. Determine the length of simple pendulum (Ls) and physical pendulum (Lp). And find the ratio of their length (Lp/Ls). d) If you doubled the length of the simple pendulum and physical pendulum, what is the period of each pendulum? e)You take these three harmonic oscillatorsto the space station and measure the period. Describe what the measured value of the period of each oscillator would be.Why?
PROPAGATION OF ERROR You are tasked to supervise the design of 0.5MW wind turbine to be constructed in a Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter. The sweeping diameter of the rotor blades is 125m, and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. if the diameter measurement is off by 0.1m and the anemometer reading is also fluctuating by 0.05m/s. In the design specifications given, if the actual measurement of power via the substation amounts to exactly 530kW and given that the windspeed is off by 0.05m/s, what could have been the error in the measurement of diameter? Your answer must be in 3 decimal places and in correct signs and measurement. Show complete solution in paper.
In the United States, electricity is sold using the SI units of kilowatt (kW) or megawatt (MW), and fuel for power generation stations is generally purchased using English units, e.g., British thermal unit (Btu), gallon (gal), and ton. An industrial power plant has an average annual load of 100 MW (electrical). If the overall thermal efficiency is 33% (based on HHV), what is the annual cost of fuel if the plant is fired with (a) natural gas, (b) No. 2 fuel oil, and (c) bituminous coal? Use the data from Tables 2.2, 2.7, and 2.13. Assume the cost of natural gas is $5/million Btu, the cost of No. 2 fuel oil is $3/gal, and the cost of bituminous coal is $60/ton (1 ton = 2000 lbm)
Find the equation of pressure, P exerted by a fluid as a function of density, r, gravity, g and height of the fluid, h.
The density of liquid water at 25 degrees celsius equals 62.2lbs/cube ft. Suppose the KD DF stud at the top of the page weighs 13.35lbs. And suppose the KD DF stud is thrown into a swimming pool, Twater=25 degrees celsius. Based on data would the stud: sink completely, partually. or float completely
The volume flow Q over a certain dam is a function of damwidth b , gravity g , and the upstream water depth H abovethe dam crest. It is known that Q is proportional to b . If b=120 ft and H =15 in., the flow rate is 600 ft 3 /s. What willbe the flow rate if H = 3 ft?
The diameter of a large offshore wind turbine is 120 m, assuming air density, 1.2 kg/m3, compute the available wind power 5, 10, 15 m/s . What is the available wind power density for wind speed of 7.5 m/s?
Fluid mechanics, i need solutions in 10 minutes please. MCQ/ what is the specific weight of the wooden beam? A-44.339 lb / ft³ B-40.842 lb / ft³ C-49.582 lb / ft³ D-55.825 lb / ft³ E-37.342 lb / ft³ F-53.144 lb / ft³ G-30.453 lb / ft³ H-51.330 lb / ft³ I-33.840 »/ ft³ J-47.835 lb / ft³ K-35.591 lb / ft³ L-28.247 lb / ft³ M-42.590 lb / ft³ N-58.631 lb / ft³