Question 2An accelerating object of mass m=13 kg is fired with an initial speed v;=6 m/s at astarting point. If its kinetic energy at its final destination is K.E=301 J. What is theresultant work (in joules) done on the object?Not yetansweredMarked out of2.00P FlagquestionA. 67B. 567С. 1067D. 867E. NonePrevious pageNext pageChapter-9-Equilibrium of( Torque and EquilibriumJump to...rigid bodies ►

According to work energy theorem Work done = change in kinetic energy

Answered: An acce starting

Science

Physics

An acce starting

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter7: Work And Kinetic Energy

Section: Chapter Questions

Problem 72P: A 500-kg dragster accelerates from rest to a final speed of 110 m/s in 400 m (about a quarter of a...

See similar textbooks

Similar questions

An electron in a television tube is accelerated uniformly from rest to a speed of 8.4107 m/s over a distance of 2.5 cm. What is the power delivered to the electron at the instant that its displacement is 1.0 cm?
Describe a situation in 4iich a force is exerted for a long time but does no work. Explain.
A 500-kg dragster accelerates from rest to a final speed of 110 m/s in 400 m (about a quarter of a mile) and encounters an average frictional force of 1200 N. What is its average power output in watts and horsepower if this takes 7.30s?
Check Your Understanding What potential energy U(x) can you substitute in Equation 8.13 that will result in motion with constant velocity of 2 m/s for a particle of mass 1 kg and mechanical energy 1 J?
Give an example of something we think of as work in everyday circumstances that is not work in the scientific sense. Is energy transferred or changed in form in your example? If so, explain how this is accomplished without doing work.
Check Your Understanding Fend the forces on the particle in Example 8.6 when kinetic energy is 1.0 J at x=0.
A particle of mass 4.0 kg is constrained to move along the x -axis under a single force F(x)=cx3 , where c=8.0N/m3 . The particle’s speed at A, where xA=1.0m , is 6.0 m/s. What is its speed at B, where xB=2.0m ?
A 200-g steel ball is tied to a 2.00m “massless” string and hung from the ceiling to make a pendulum, and then, the ball is brought to a position making a 30 angle with the vertical direction and released from rest. Ignoring the effects of the air resistance, find the speed of the ball when the string (a) is vertically down, (b) makes an angle of 20 with the vertical and (c) makes an angle of 10 with the vertical.
A baseball of mass 0.25 kg is hit at home plate with a speed of 40 m/s. When it lands in a seat in the left-field bleachers a horizontal distance 120 m from home plate, it is moving at 30 m/s. If the ball lands 20 m above the spot where it was hit, how much work is done on it by air resistance?
A particle of mass 2.0 kg moves under the influence of the force F(x)=(5x2=7x)N . Suppose a frictional force also acts on the particle. If the particle’s speed when it starts at x=4.0 m is 0.0 m/s and when it arrives at x=4.0 m is 9.0 m/s, how much work is done on it by the frictional force between x=4.0 m and x=4.0 m?
A mouse of mass 200 g falls 100 m down a vertical mine shaft and lands at the bottom with a speed of 8.0 m/s. During its fall, how much work is done on the mouse by air resistance?
A 100 — kg man is skiing across level ground at a speed of 8.0 m/s when he comes to the small slope 1.8 m higher than ground level shown in the following figure. (a) If the skier coasts up the bill, what is his speed when he reaches the top plateau? Assume friction between the snow and skis is negligible. (b) What is his speed when he reaches the upper level if an 80 — N frictional force acts on the skis?