An air-filled rectangular waveguide is to be constructed for single-mode operation at 15GHz. Specify the guide dimensions a and b, such that the design frequency is 10 percent higher than the cutoff frequency for the TE10 mode, while being 10 percent lower than the cutoff frequency for the next-higher-order mode.

An air-filled rectangular waveguide is to be constructed for single-mode operation at 15GHz. Specify the guide dimensions a and b, such that the design frequency is 10 percent higher than the cutoff frequency for the TE10 mode, while being 10 percent lower than the cutoff frequency for the next-higher-order mode.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An attenuator can be made using a section of waveguide operating below cutoff, as shown in theaccompanying figure. If a = 2.286 cm and the operating frequency is 12 GHz, determine the requiredlength of the below-cutoff section of waveguide to achieve an attenuation of 100 dB between the inputand output guides. Ignore the effect of reflections at the step discontinuities.
A 5.0 × 2.0 mm2air-filled rectangular waveguide is to operate below85 GHz. Determine the number of TE and TM modes that can be transmitted in the waveguide. Subsequently, sketch the cross-sectional view of field line distributions for TE10, TE11, and TM11 modes.
In an air-filled rectangular waveguide, the cutofffrequency of a TE10 mode is 5 GHz, whereas that ofTE01 mode is 12 GHz. Calculate(a) The dimensions of the guide.(b) The cutoff frequencies of the next threehigher TE modes.(c) The cutoff frequency for TE11 mode if theguide is filled with a lossless material havingr = 2.25 and r = 1.
The dimensions of a rectangular metallic waveguide are 1.58x0.79 cm. Assuming that the inside of the waveguide is air;a) Find the cutoff frequencies for TE10, TE20, TE01 and TE11 modes.b) What modes can propagate in this waveguide in the frequency range 12 GHz to 18 GHz?c) If this waveguide is used to transmit a 10 GHz frequency signal in TE10 mode, what will be the phase speed of the signal?
For a 12-GHz signal travelling in a rectangular waveguide with an inner cross section of 25 mm x 12 mm. Calculate the following: phase velocity, group velocity, guide wavelength and characteristic impedance.
How to design wide band microstrip antenna in single, linear, and planar array to cover the bandwidth for 5G applications in mm waves bands? And what is best softawe use for design and simulation? Thanks in advance..
if in a rectangular waveguide for which a=2b , the cuttoff frequency for TE02 mode is 12 GHz ,the cutoff frequency for TM11 mode is
How large dish diameter is needed for 80 dB gain at 300 MHz?
A 162-MHz carrier is deviated by 12 kHz by a 2-kHz modulating signal. The maximum deviation of an FM carrier with a 2.5-kHz signal is 4 kHz. Compute the bandwidth occupied by the signal, by using the conventional method and Carson’s rule. Sketch the spectrum of each signal, showing all significant sidebands and their exact amplitude.
What is the maximum frequency (in GHz) that a single-line bus with a length of 1 meter can operate at without experiencing significant signal degradation, assuming a rise/fall time of 10% of the signal period and a characteristic impedance of 50 ohms?
Consider a mobile system at 900 MHz carrier frequency, and with 25-kHz bandwidth, that is affected by thermal noise (noise temp Te = 300k). Antenna gains of Tx and Rx sides are 8dB and -2dB respectively. Cable loss at Tx is 2dB. The noise figure at Rx is 7dB. The required operating SNR is 18dB and desired range of coverage is 2km. The break point is at 10dB up to which the path loss is given by [ ] , beyond that point the path loss exponent is 3.8, and the fading margin is 10dB. What is the minimum Tx power required?
What is the cut-off wavelength (mm) of an air-filled 3.1 cm x 2 cm rectangular waveguide operating at TE21 mode?