An airplane is cruising at an elevation of 35,000 feet from sea level. Determine the amount of gage pressure in bars needed to pressurize the airplane to simulate sea level conditions. The average atmospheric pressure on earth is mated as a function of altitude by the relation Patm = 101.325 (1- 0.02256z)5.256, where Patm is the atmospheric pressure in kPa and z is the altitude in km with z = 0 at sea level.

Q: QUESTION 1 Locate the centroid y of the shaded area. 1 10 in 9 in O 1.6 in O -0.2 in 3.6 in 5.8 in…

A:

Q: A fuel has the following constituents: carbon 85%, hyrdogen 13%, oxygen 2%. When burning this fuel…

A: GivenC=85%H=13%O=2%air supply is 50% in excess

Q: What is the area of a rectangular air supply opening measuring 12x10?

A: Given data  Side of a rectangular = 12 × 10 Find the area of rectangular Use  Area = length × width…

Q: what is x-distance from the origin the resultant force act ! unit [m]. Iwould need

A: Different forces are shown . We need to apply a force which will maintain the dynamics and…

Q: Replace the distributed loading with an equivalent resultant force, and specify its location on the…

A: Given:

Q: 6. What is the maximum load (in kN) which can be handled safely by the lap joint shown if the shear…

A:

Q: A power of 120 kW is transmitted into a single reduction gear system through a pinion with 250 mm…

A:

Q: A 16-cm x 20-cm gas engine has a normal speed of 450 rpm. Determine: a.) the speed, in rev/s and…

A: Given data: 16-cm x 20-cm  Length of stroke of engine(piston)=20cm or 0.20m engine  normal speed is…

Q: *5-16. The linkage supports a force of 500 lb and rides along the top and bottom flanges of the…

A:

Q: 1- Calculate the water discharge in the following system (assume Ks=0.00004m, D=26 cm, v=1.07x106…

A:

Q: 5. What is the temperature profile T(2) for an atmosphere with uni or n lapse rate y = -dT/dz and…

A:

Q: A piston is moving through a cylinder at a speed of 19 ft/s, as shown in the figure. The film of oil…

A:

Q: 5-15. Determine the reaction at fixed support A. Problem 5-15 A 6 m 0.5 kN/m 3 m- 3 kN 5 kN.m

A:

Q: Compute the specific volume, temperature, or pressure (as the case may be) using the ideal gas…

A: Given: To find T, P, v using ideal gas equation T, P, v using generalized Compressibility chart

Q: Can you show me how to solve it using FLT?

A:

Q: For determining the centroid of the area marked below in blue, you could to consider two square…

A:

Q: Learning Goal: To apply the condition of equilibrium to three- dimensional systems and solve for…

A:

Q: Problem 3: Moment M is another way to draw a moment rather than a curved arrow. If M = 30000 N·mm,…

A: GivenM=30000 Nmm

Q: e Materials Science and Materials Engineering. Enumerate 5 examples of Ceramics. Enumerate 5…

A: Materials engineers typically work in the manufacturing industry and may be engaged in the…

Q: A fuel of Q₁ = 6888 kcal/kg was burned in the furnace of a 223 m² water tube boiler which was…

A:

Q: During a steady flow process, the pressure of the working substance drops from 180 psia to 30 psia,…

A:

Q: 1. An aluminum rod 15 cm long with a diameter of 1.0 cm is fixed between rigid supports with an…

A:

Q: From the speed chart below, determine the correct cutting speed for facing an Aluminum part on a…

A: From the speed chart below, determine the correct cutting speed for facing an Aluminum part on a…

Q: The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is…

A: Given Data: Mass of Wheel m=20 kg Radius of Wheel R=0.6 m Radius of gyration KG=0.4 m Unstretched…

Q: Consider a rigid tank of 2m³ containing pressurized air at 400kPa and 25°C. The tank slowly deflates…

A:

Q: PROBLEM 2.0 Determine the viscosity of a fluid having kinematic viscosity 6 stokes and specific…

A: Given data: kinematic viscosityv=6 stokesSG=1.9 Need to determine the viscosity of the fluid.

Q: 2. A slender, uniform bar weighs 193 lbs and is shown below. It has an angular velocity of 2 rad/sec…

A:

Q: 1. Determine the amount of energy (kJ) that needs to be transferred to the water to raise its…

A:

Q: Determine the magnitude of the resultant force if 8 = 32 degrees and T = 10 kN. Provide the answer…

A:

Q: The truck and the tanker have weights of 8000 lb and 20000 lb, respectively. Their respective…

A: Given that: Weight of the truck is 8000 lb and it is acting at G1. Weight of the tanker is 20000 lb…

Q: etermine the final velocity of a truck that is initially traveling at 10 m/s and travels 500m over…

A: Given:Initial velocity of the truck, u=10 m/sDistance covered by the truck, S=500 mTime taken, t=13…

Q: Learning Goal: To apply the condition of equilibrium to three- dimensional systems and solve for…

A: Given data, Given data, Coordinate of A = (d, 0, 0) = (3.5, 0, 0) ft Coordinate of B = (0, a, 0) =…

Q: 5-46. Three uniform books, each having a weight W and length a, are stacked as shown. Determine the…

A:

Q: 2. How far from the axis of A will the center of the roller R be located if the angular speed of…

A:

Q: tant snown, an angular and an angular acceleration of 2 rad/s², both determine the angular…

A:

Q: A 2.0-m-long wire stretches 1.0 mm when subjected to a load. What is the tensile strain in the wire?…

A: GivenLength of wire L=2m∆L=1mm=1×10-3 m

Q: Which of the following is NOT a Mechanical Engineering Student Shop safety rule? Wear open shoes Put…

A: Which of the following is NOT a Mechanical Engineering Student Shop safety rule?   A) Wear open…

Q: In a positive angle, the terminal side inclines _____________ from the initial side

A: Answer :- counterclockwise

Q: 1 and 2 are rolling cylinders connecting shafts A and B. 3 and 4 are cylinders fastened to these…

A:

Q: 3. Determine the stress and strain in the cable on the upper beam

A:

Q: 3.5 Imagine that you are instructed to find suitable material types and processing techniques to…

A: Given question is related to manufacturing engineering.     [ Note : According to Bartleby's…

Q: 5. The temperature at the point (z,y) on a metal plate is modeled by T(x,y) 400e-(+)/2 in °C, with…

A: Given: T(x,y) = 400e-(x2+y)/2 Point = (3,5) To find: Direction in which there is no change in T

Q: 2. The wheel shown below has a mass of 5 slugs and a radius of gyration for the z-axis through point…

A:

Q: What is the measurement indicated in the below photo? יןיייויייןיייני 1 ................. Fill in…

A: As from the given figure the pointer is between 1 and 2 inches of the ruler. It lies mid way of 1…

Q: By circle of Mohr 15 O 0 13 13 7 A 13 C ㅋ Jij Find the main efforts می

A:

Q: is offset by wind power. Assume that when the coal plant runs at its constant power it has an…

A:

Q: Water P=200kPa, h=600kJ/kg. v? T?

A:

Q: 2.1 What is the value of vertical reaction V₂?

A:

Q: Problem 2. A block of cast iron was wrapped in the thin aluminum foil as shown on the figure. At…

A: Solution: Given Data: *The initial stress in the foil, σi=0 *The temperature of the Nitrogen is,…

Q: A series of bricks, whose thickness are all equal to 1.3 m, are arrange according to the figure…

A: Given question is related to heat transfer.