An aluminum pan whose thermal conductivity is 237 W/m °C has a flat bottom with diameter 20 cm and thick- ness 0.4 cm. Heat is transferred steadily to boiling water in the pan through its bottom at a rate of 800 W. If the inner surface of the bottom of the pan is at 105°C, determine the temperature of the outer surface of the bottom of the pan.

An aluminum pan whose thermal conductivity is 237 W/m °C has a flat bottom with diameter 20 cm and thick- ness 0.4 cm. Heat is transferred steadily to boiling water in the pan through its bottom at a rate of 800 W. If the inner surface of the bottom of the pan is at 105°C, determine the temperature of the outer surface of the bottom of the pan.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.19P: 1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the...

See similar textbooks

Similar questions

1.29 A spherical interplanetary probe with a 30-cm diameter contains electronic equipment that dissipates 100 W. If the probe surface has an emissivity of 0.8, what is its surface temperature in outer space? State your assumptions in the calculations.
In determining the average rate of heating of a tank of 20% sugar syrup, thetemperature at the beginning was 20°C and it took 30 min to heat to 80°C. Thevolume of the sugar syrup was 50 ft3 and its density 66.9 lb/ft3. The specific heat ofthe sugar syrup is 0.9 Btu lb-1°F-1.(a) Convert the specific heat to kJ kg-1°C-1.(b) Determine the rate of heating, that is the heat energy transferred in unit time, in SI units (kJ s-1)
1. Consider a person standing in a room at 25°C. Determine the total rate of heat transfer and the heat transfer coefficient from this person if the exposed surface area and the skin temperature of the person are1.7 m 2 and 33°C, respectively, and the convection heat transfer coefficient is 5 W/m 2 · °C. Take the emissivity of the skin and the clothes to be 0.9, and assume the temperature of the inner surfaces of the room to be the same as the air temperature. (complete solution thank you)
A 10 cm diameter aluminum ball is to be heated from 94°C to an average temperature of 140°C in 30 minutes. Taking the average density and specific heat of aluminum in this temperature range to be 2,700 kg/m3 and Cp = 0.91 kJ/kg-K, respectively, determine the ff: (Round off your final answers to two (2) decimal places.) (a) the total amount of heat transferred to the ball in kJ = (b) the average heat transfer rate to the aluminum ball in W = (c) the average heat flux in W/m2 =
applications of DE a body at a temperature of 200F is placed in room at a constant temperature of 10F. If after 20 min the temperature of the body is 50F, A. Determine the temperature of the body at any time t and its temperature at t = 0.75hr. B. Find the time it will take for the body to reach a temperature of 25F.
The temperature on the two surfaces of a 25mm thick steel plate (k=48w/m°c)
The inside and outside surfaces of a 1-cm thick, 4-m squared-shaped window glass in winter are 9°C and 1°C, respectively. If the thermal conductivity of the glass is 0.78 W/m-K, determine the heat loss, in kcal, through the glass over a period of 8 hours.
Before the widespread use of mechanical refrigeration, cooling was provided by ice, which was delivered by icemen and stored in an icebox. In a current application, blocks of ice at Tice = 32°F with a total mass of mice = 500 lbm are placed in a large food-storage icebox that is used to keep food at Tfood = 45°F on a day in which the outdoor temperature is Tamb = 78°F. The rate of heat loss through the walls of the ice box is Q = 2900 Btu/hr. a.) Estimate the amount of time the ice it will take this ice to melt. b.) Compare the rate of cooling provided in ton units to the mass of ice in tons. c.) Define and calculate efficiency for this process. d.) Determine the change in exergy of the ice in this process. e.) Calculate the Second-Law efficiency for this process.
The roof of an electrically heated home is 12m long, 16m wide, and 0.50m thick, and is made of a flat layer concrete whose thermal conductivity is k=0.8W/m 2 ·°C. The temperature of the inner and outer surfaces of the roof one night are measured to be 12°C and 1°C, respectively, for a period of 12 hours. Determine a) the rate of heat loss through the roof that night b) the cost of that heat loss to the home owner if the cost of electricity is $0.14/kWh.
A 20lbm object is located 300 ft above the ground. What is the potential energy of the object in lbfft, BTU, and cal?( 3pts
A fan forces air over a computer circuit board with an area of 0.01 m2 to keep the circuit board cool. If the temperature of the surface is at 350 K and the incoming air is at 298 K, determine the rate of heat transfer in W. Assume the heat transfer coefficient is 20 W/(m2K). Report your answer to one decimal place.
A piston–cylinder device contains 4 kg of argon at 250 kPa and 35°C. During a quasi-equilibrium, isothermal expansion process, 12 kJ of boundary work is done by the system, and 3 kJ of paddle-wheel work is done on the system. Determine the heat transfer for this process. (Round the final answer to the nearest whole number.) The heat transfer for this process is ................... kJ