An angle L5x5x5 tension member of A36 steel is connected to a gusset plate with six 3/4-inch diameter bolts as shown in Figure 3. If the member is subject to dead load and live load only, what is the maximum total service load that can be applied if the ratio of live load to dead load is 3.0? Use the alternative value of U from AISC Table D3.1. L5x5x% 1/2" p 0000 H 5 spaces @ 3" = 15" Figure 3 1/2"

An angle L5x5x5 tension member of A36 steel is connected to a gusset plate with six 3/4-inch diameter bolts as shown in Figure 3. If the member is subject to dead load and live load only, what is the maximum total service load that can be applied if the ratio of live load to dead load is 3.0? Use the alternative value of U from AISC Table D3.1. L5x5x% 1/2" p 0000 H 5 spaces @ 3" = 15" Figure 3 1/2"

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.3.4P

See similar textbooks

Similar questions

A double-angle shape, 2-L6 × 6 × 5⁄8, is connected to a 5⁄8-inch gusset plate as shown in the figure. Determine the maximum total service load that can be applied if the ratio of dead load to live load is 3.50. The bolts are 7⁄8-inch-diameter. A572 Grade 50 steel is used for the angle (Fy = 350 MPa; Fu = 450 MPa), and A36 steel is used for the gusset plate (Fy = 250 MPa; Fu = 400 MPa). Assume bolt shear strength is NOT critical. Check both the capacity of the tension member and the gusset plate (Hint: for gusset plate, only block shear and bearing strength may be checked). Use LRFD specifications. Note: The gage distances are 2 inches each. AISC (13TH EDITION) (3DECIMALS) need in 3hours pleasee.
The given angle bar L125x75x12mm with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm diameter bolts as shown in the figure. Using A36 steel with Fy = 248 MPa and Fu = 400 MPa, determine the following: a. nominal tensile strength (kN) based on gross yielding.
3. A single angle tension member L89x89x9.5 with an area of 1,800mm2 connected to a gusset plate with 22 mm diameter bolts as shown in the figure. A36 steel is used with Fy=248 MPa and Fu= 400 MPa. The service loads are 150 KN dead load and 65 KN live load. Investigate the adequacy of the member. Diameter of hole is 3 mm bigger than bolt diameter and use net area equal to 85% of the computed net area. Neglect block shear. a. Check using ASD Load Combination b. Check using LRFD load combination
1. An unsymmetrical flexural member consists of a 70 × 600 top flange, a 70 x 400 bottom flange, and a 12 × 180 web. a, Determine the Section Modulus. b. Determine the distance from the bottom of the shape to the horizontal plastic neutral axis. ( Take note: Bottom Distance i need, not the top distance) c. If A572 Grade 50 steel is used, what is the plastic moment MPy for the horizontal plastic neutral axis?
: Verify, using appropriate Chapter E design provisions, the tabularized (Table 4-7) buckling capacity of a WT6X20 for both the x- and y-axes at (KL)x = (KL)y = (KL)z = 10 ft. Assume A992 steel.
5. a bolted lap joint shown in the figure below. The bolts are 20m in diameter in 23 mm holes. The plates are 12m thick X350 Allowable stress of Plates: Tenaion in gross area0.60Fy Tension in net area0.50 Fu Shear on Net Area 0.30Fu Yield Strength of plate, Fy 248 Npa Ultinate tensile strength of Plate. Fu400 Mpa x, Find the safe load P based on a- Gross area yielding b. net area rapture c. block shear 2 of 3
The tension member shown in Figure is an L6 × 3 ½× 5/16. The bolts are ¾ inch ameter. If A36 steel is used, is the member adequate for a total load of 100 kips?
An unsymmetrical flexural member consists ofa 3 x 30 in. top flange, a 3 x 20 in. bottom flange, and a 60 * 2 in web A. Determine the distance from the top ofthe shape to the horizontal plastic neutral axis. B. If A572 Grade 50 steel is used, what is the plastic moment Mp for the horizontal plastic neutral axis?
1. An unsymmetrical flexural member consists of a 70 × 600 top flange, a 70 x 400 bottom flange, and a 12 × 180 web. a, Determine the Section Modulus. b. Determine the distance from the bottom of the shape to the horizontal plastic neutral axis. c. If A572 Grade 50 steel is used, what is the plastic moment MPy for the horizontal plastic neutral axis?
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the allowable tensile strength of the section based on tensile rupture of the net area.
Subject: Steel Design A W300 x 67 has two lines of 20 mm dia. Bolts in each flange (3 bolts in each line which has spacing as shown. A36 steel is used with Fy = 250 MPa, Fu = 400 MPa. Properties of W300 x 67 A = 8250 mm2 bf = 201.05 mm tf = 14.40 mm d = 300mm tw = 8.4 mm a) Compute the effective net area of the section b) Compute the allowable tensile strength of the section. Note: Dimensions in the drawing are in mm
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the design tensile strength of the section based on tensile rupture of the net area. Determine the allowable tensile strength of the section based on yielding of the gross area.